How to make hanging flower pots. DIY hanging planter. Making flower pots from plastic bottles with your own hands

Often, houseplants are placed on the windowsill - closer to natural light. If the window sill is very narrow and there is not enough space to place houseplants in flower pots, you can grow flowers together on hanging devices. In this case, a way out can be hanging basket or flowerpot . A flowerpot is a hanging container in which a single pot with a flower or green plant. More interesting option is a hanging basket in which several plants are planted at the same time, forming a flower arrangement.

There are a number of difficulties that can complicate the process of growing plants this way. But thanks to our advice, you can choose appropriate place, correctly arrange the composition and properly care for flowers in hanging containers:

• Tip 1: It must be remembered that warm and dry air rises, so plants suspended structure More frequent watering will be required.
• Tip 2: If you overfill the water, it may flow directly onto the floor. This threatens to bloat wooden floor Therefore, the optimal place for hanging baskets is a kitchen or balcony, where the floors are usually laid with tiles.
• Tip 3: For baskets placed indoors, polyethylene is sometimes placed inside the container to prevent water from dripping, but this poses a risk of flooding the plants. The best decision is to place several pots of plants in a waterproof container. The container itself can be hung on a wire, rope or twine from the ceiling. The principle of this placement is similar to the flower girl, which is described in the article about a home mini-garden.
• Tip 4: The gaps between the pots and the walls of the container are filled with wet peat. Peat is lighter than, for example, a mixture of peat and soil, and when hanging from the ceiling, unnecessary loads should be avoided.

• Tip 5: If you have chosen the option of planting plants in total capacity, then the rules here remain unchanged: plants must have the same watering regime, temperature regime and be equally sensitive to light. As for the soil, it is poured into a container on top of the drainage layer, which is also general rule for this method of growing plants.
• Tip 6: It is better to hang the basket in such a way that you can reach it with your hand, that is, at the level of your height. If this option is not possible for some reason, then use not a simple hook, but a carabiner; this design will allow you to raise and lower the container.
• Tip 7: One last tip: check that your green pets are getting enough light and air at the chosen height. Flowering and variegated plants should be placed closer to the light - near the window.

Examples flower arrangements in a flowerpot:

Even the brightest ones need a frame - “outfits” that will further emphasize their beauty. The most spectacular and at the same time simple “outfits” are rightfully considered outdoor flower pots. Making them with your own hands will not be difficult. Do you want hanging planters made from bottles, wicker from wicker, or ground-mounted from a tree stump? No problem! Read the instructions on how to make flowerpots from these and other materials, and also watch educational photos and videos - they will help you transform your garden beyond recognition.

Making flower pots from rags and cement

To make such a flowerpot, you will need:

• cement;
• old tablecloth;
• vase, pot or other vessel for form;
• water;
• bucket;
• “mixer” – attachment for a drill;
• dye.

The procedure for creating a flowerpot is very simple. First you need to prepare cement mixture. To accurately determine its volume, take a tablecloth, place it in a bucket and mark on the walls how much space it takes up - according to this mark, pour water for the solution. Add cement to the water and mix them with a “mixer”. The result should be cement laitance, reminiscent of slightly runny sour cream in consistency.

Then, when the mixture is ready, place the tablecloth in it and leave for a couple of minutes until it is completely soaked. After this, remove the material and make sure that there are no dry areas left on it.

Next, take the prepared container for the mold and hang a wet tablecloth on it. Gently straighten the material and leave to dry. When cement mortar completely hardens, remove the product from the container-form and paint. Use special paints for concrete - they are stronger and more durable. Once the paint has dried, you can use the pots for their intended purpose.

Making flower pots from plastic bottles with your own hands

Plastic containers – universal material for flower pots, since several models of “outfits” can be built from it at once.

The first option is a classic flowerpot. Take a plastic bottle, two CDs, sandpaper, scissors, glue and paint. Cut the bottle into two equal parts using a wavy line. Clear sandpaper both disks. Take the bottom of the bottle and glue it to the stripped first disc. Then take the top part: first unscrew the cap and glue it to the second disk, and as soon as the glue dries, screw the plastic part of the bottle back to the cap. When finished, coat the pieces with paint.

The second option is a hanging planter. Here you will need: bottle, rope, paints, scissors. First, cut off the neck of the bottle - only a straight line will be used in this work. Bottom part containers. Then cut small holes on the sides for the rope. Then decorate the structure: paint, cut out patterns, draw an animal, trim the top edge - whatever you can do carefully. And then thread a rope through the holes, place a flower pot in the flowerpot and hang the structure on strong nails.

We make wooden flower pots

Easiest to do flower pot from a stump or log. Take:

• wood;
• drill: drill length – at least 25 cm, diameter – at least 20 cm;
• chisel;
• protective impregnation for wood.

1. Select a log or stump of the required diameter. Measure a piece to the height of the flower pot or flowerpot and cut it off - this is again a flowerpot.
2. Drill a series of holes into the top plane of the wood to destroy the core.
3. Use a chisel to remove the wood - you should end up with an empty container. The edges need to be aligned.
4. Process internal walls flowerpot protective composition and place a flower pot in it.

Advice. The wooden planter itself can also serve as a pot, but to do this, you need to put durable polyethylene in the container and cover it with drainage on top. And only after that you can place the soil mixture with the flower.

A more complex option is a flowerpot made of boards and timber. You will need:

• beams with a section of 25x25 mm;
• boards 15 m thick;
• self-tapping screws;
• wood glue;
• drill;
• protective impregnation for wood.

The algorithm for making pots is as follows:

1. Assemble a cube-shaped frame from the beams.
2. Cut out parts for the bottom and walls from the boards. Sand the panels on all sides.
3. Drill several holes in the bottom for drainage.
4. Assemble the design of the flowerpots together: attach the side and bottom panels to the cubic frame using self-tapping screws. In order to give the product even greater reliability, carefully glue all joints.
5. Cover the surface finished design protective composition.

We weave flowerpots from wicker

Another simple but interesting option for a flower “outfit” is a flowerpot made of vines. Prepare for work:

• flexible vine - it can be either fresh or dried;
• plywood sheet;
• moisture-proof impregnation;
• drill;
• awl;

First, soak the vine in water - this will give it the extra flexibility needed for easy weaving. Cut from plywood sheet blank for the bottom oval or round shape. Along the edge of the resulting bottom, drill identical holes with a diameter slightly smaller than the diameter of the vine. All holes should be at the same distance from the edge of the bottom. Then insert a strong twig into each hole - this will be a blank for the frame of the flowerpot.

The next step is direct weaving: lay the vine between the rods, carefully pressing each new row with an awl. Wrap the twigs until the product reaches the height you require. Laying methods can and even need to be changed after a row - this way you will achieve a different textured surface of the pots.

At the end of the weaving, either cut the twigs or weave them into the main rows of the vine. Then let the structure dry a little and get stronger. Final stage– treatment of flowerpots with moisture-proof impregnation and varnishing.

We make plant pots from plaster

To make such a pot, prepare:

• gypsum;
• wire;
• textile strips no more than 10 cm wide;
• paint;
• bucket;
• protective varnish.

The first step is preparing the frame. Turn the bucket upside down and braid its surface with wire. Tuck the edges and hide. Carefully remove finished frame from a bucket.

The second step is diluting the gypsum solution. Take gypsum and mix it with water until the mixture begins to resemble sour cream.

The third step is the construction of the “body” of the flowerpot. Dip all textile strips into the plaster solution and soak for 3 minutes. Then take out the tapes one by one and place them on the frame layer by layer. The thickness of the walls should be at least 2 cm. Then carefully treat the walls of the structure with the remaining gypsum mortar. After this, the pot should dry completely - set it aside for 10-12 hours.

The fourth step is design design. Flowerpots can not only be painted, but also decorated with a variety of pieces of glass, beads, pebbles - any small details that you like.

Advice. After drying, the walls of the pots will not be completely smooth, so the paint will not apply well. To avoid this, carefully clean the surface with sandpaper and treat the structure with white water-based composition, and then apply paint of the required color to the flower pots in the second layer.

Now you know what to do beautiful flowerpot for flowers you can use almost any materials without spending a lot of time or a lot of money. The main thing is to turn on your imagination and be smart. So if you want to effectively decorate your garden, don’t rush to buy store-bought pots – take the initiative into your own hands and don’t be afraid to experiment.

How to make a flowerpot: video

Planters for the garden: photo

Warm days are approaching, and many will want to take their flowers out onto the balcony or loggia. But sometimes there is not enough space for flowers and you have to look for ways to place them. I like it vertical gardening. And for convenience vertical arrangement flower pots You can make a flowerpot for them with your own hands using available materials.

• 1 Hanging planter from strips of fabric
  • 1.1 Pot made from a plastic bottle
  • 1.2 This is also interesting

Hanging planter made from fabric strips

Almost every woman collects several knitted T-shirts over the course of a season, which she no longer wants to wear and would be a pity to throw away. You can make a lot of useful things from them, as well as make cords for weaving flowerpots.

To do this, you need to cut strips about 2 cm wide across the product. It is better not to use a hemmed edge. You should end up with a ring with two seams, one of which needs to be cut, and then the strip should be stretched. You will need from 4 to 6 strips depending on the length.

If the strips are long, then 4 pieces will be enough. They need to be tied into a knot in the middle. For short strips, make the knot closer to the edge.

Then you can start weaving flowerpots. For convenience, you can use an empty flower pot.

The photo shows in some detail the scheme for connecting the strips. Repeat the process of tying knots depending on the height of the pot to prevent it from falling out of the pot in the future.

The remaining ends of the cords can be simply tied into a knot, or they can be tied to a ring to make hanging more convenient.

Pot made from a plastic bottle

This pot is more suitable for use in the country. Cut off the top of a plastic bottle the right size. It is better to melt the cut edges to avoid injury or damage to the plants later. Make 3-4 holes and stretch the rope through them.

Such a pot can be hung on an old tree or used on a balcony, having previously planted flowers or herbs in it.

In the same way, you can use plastic bottles with handles from under household chemicals. Naturally, they need to be washed thoroughly before use.

Then cut off the bottom of the bottles, turn them upside down, attach them somewhere, fill them with soil and plant the plants. By the way, if you do not tighten the lid tightly, excess moisture will not be retained in the container and the roots of the plants will not rot.

Of course, the bottles can be decorated beforehand, but only if the desire arises.

The charm of the most beautiful and well-groomed plants will not be complete if they are planted in assorted pots that differ in shape, size, and the material from which they are made. Perfect solution problems – flower pots. Purchased in a store or made with your own hands, they will complete the look of the collection and help decorate a country plot.

Selection of ready-made pots for indoor and garden plants

The range of ready-made flowerpots in stores is incredibly large. In order not to get confused when choosing, experts advise paying attention to several aspects. Among them:

• the price of the sample you like;
• destination of the pot;
• the size of the pot to be decorated;
• compliance with the style of interior or landscape design;
• practicality of the product.

Most often, flower growers prefer flower pots made from polymer materials, fired ceramics or clay, glass.

Flower pots made of plastic

The most affordable samples are made of plastic. They are easy to clean and can be used indoors and outdoors. Thanks to the presence of drainage holes and the ability to easily make new ones, the plants in the pots are protected from rotting of the root system. Another useful quality– lightness, which is important if a gardener needs a hanging flowerpot for hanging plants or a spectacular garland of their flower pots. Despite the thin walls, the container exposed to the sun does not heat up to critical temperatures, does not cause overheating of the soil and root system.

If desired, plastic flowerpots can be easily decorated with fragments of wood, textiles, beads, or simply painted using safe and bright acrylic paints.

A store-bought plastic planter can be easily transformed with a roll of string and glue. Processed by him lateral surface tightly wrapped with twine or cord.

However, with a lot of advantages, plastic flowerpots have a couple of disadvantages. They are not very durable when used outside the home, and the products cannot be called original.

Ceramic flower pots

Ceramics different types has long been used to make flower pots and flowerpots. Clay is incredibly malleable. She can take the most different shapes, natural material keeps the warmth of the master’s hands, transferring it to the interior or summer cottage.

When choosing a ceramic pot, you should pay attention to the presence of a drainage hole, as well as the outer covering.

Unglazed clay retains porosity, which improves the microclimate inside the pot, but reduces the durability of flower pots. When watering tap water Untidy stains may appear on the walls. Outside the home, containers are in danger of destruction:

• increased air humidity;
• sudden changes in temperature, especially freezing and thawing.

Painted or glazed ceramics look very impressive and are much stronger, but they warm up slowly and do not remove excess moisture well.

Because of heavy weight For ceramic products, especially when making hanging flower pots with your own hands, you need reliable fastening. It's easy to make using strong twine and macrame techniques.

Glass flower pot

Transparent or colored glass- fragile, but spectacular material, which will help decorate the interior and make the house unique.

At the same time, showing your imagination, make a similar flowerpot with your own hands for indoor flowers It's not difficult at all.

As a basis you can take glass jars suitable size, glasses, vases or even a small round aquarium. By connecting the vessels with a rope and securing them to a wooden stand, you can build a garland for flowers or make a flowerpot for several pots at once.

How and from what to make a flower pot with your own hands

The decoration of the window sill and garden will be flowerpots that were not found in the store, but were made by the gardener himself. Such samples are usually:

• many times cheaper than analogues from the store;
• created taking into account the tastes and preferences of the master;
• unique.

But, relying on his imagination, the gardener needs to remember about the reliability of the future flowerpot, safety and practicality. It is especially important to take into account weather variability and the impact external factors, if you have to assemble a flowerpot for the garden with your own hands.

The most popular materials suitable for this work:

• wood, including planks, bamboo, dry branches collected from the garden;
• cement mixtures that turn into durable, moisture-resistant structures after hardening;
• durable types of twine and rope from which wicker flowerpots are made;
• textiles treated with wear-resistant paint.

You don’t have to go to the store to buy an original flowerpot or materials for making it.

One has only to look around to notice things that have fallen out of use, but can turn into a unique interior or landscape object.

DIY hanging flower pot

Handmade flowerpots for the home are a great opportunity to show your imagination and demonstrate your ability to create practical and absolutely unique things.

The simplest option is a hanging planter using the macrame technique. Woven to fit the size of the pot, it:

• fits perfectly into the interior;
• decorates any container in which an indoor flower grows;
• can be used for ordinary and hanging plants;
• in combination with others, it forms a multi-tiered garland, saving space on the windowsill and giving the window a unique look.

In addition, the flowerpot allows you to significantly improve the lighting of plants and simplifies care when large quantities flowers in the house.

When choosing a rope for weaving, it is better to give preference to samples made of wear-resistant fiber that does not stretch under load, does not fade in the sun and is not afraid of moisture. The same requirements apply to wicker flower pots for outdoor use.

Floor and table flower pots

Large plants, e.g. indoor lemon, monstera, ficus or lush fern are a magnificent home decoration. To make them look even more impressive, the pot can be placed in an original flowerpot.

Choose an option suitable design and size is not always possible, but everyone can make a tall floor planter for flowers on their own.

One option is a cement pot. As a base, a quickly hardening mixture is taken, which is poured into a prepared mold and after some time a strong casting-pot is obtained. Another way to use the material is to drink it through a textile scrap and give it suitable look, wait for the composition to dry. This pot can be used indoors and outdoors. garden plot. For more decorative effect the casting is painted and even covered with mosaics.

A wonderful flowerpot for big flower A box of a suitable shape will serve. It is first sanded, treated with moisture-proof varnish or painted. To protect the floor and other surfaces such as tables underneath wooden flowerpots for a flower, place a tray on the bottom to collect excess moisture. Free space Between the pot and the planter can be filled with coconut fiber.

Make caring for your green pet easier large sizes, a pot with a built-in watering system will help protect the plant from moisture deficiency and drying out. You can buy it or make it yourself from scrap materials.

In addition to the container for the pot, there is a cavity for water and a tube for filling it, as well as a system of holes that supply moisture to the roots and remove excess moisture. Similar design for flowers of any size can be assembled at home. It will be useful both on the windowsill and in the garden, especially when the plants are deprived of the daily attention of the gardener.

The simplest flowerpot with automatic watering can be made from an ordinary one. plastic pot. The main thing is that it is of a suitable size, and its bottom has many large drainage holes. The shipping container in which the flowers arrive at the store is perfect. Under drainage, laid at the bottom mosquito net made of plastic. It will prevent the soil from being washed away. Several nylon cords are threaded through the holes so that their ends remain hanging freely.

By placing such pots with home or garden flowers on gravel in a tray filled with water, you can be sure that the plant will not suffer from drying out. The liquid will rise along the rope to the ground, but will not cause root rot.

Making a hanging flowerpot with your own hands - video

Decorating both interiors and landscapes with flowers is in demand among many people. They are successfully used by designers to implement their projects. For a more harmonious fit, use do-it-yourself flower pots, which they create at master classes based on their own sketches. But they are not the only ones who use such techniques, ordinary people successfully come up with complex designs from what is “at hand”.

Types of flowerpots by material

Hanging decorations should be selected based on location, permissible weight per support, amount of water consumed by the plant and temperature conditions. The materials are as follows:

Available on the market a large assortment, but some people prefer to make outdoor hanging flower pots with their own hands and admire their creation. Hangers for pots are made from chains, ropes, metal rods and from pieces of fabric, twine and yarn using the macrame technique.

Cage, chandelier or wooden boxes

A frameless wall-mounted planter is formed directly from coconut fiber. The roots of the plant with a lump of soil are wrapped in a piece of polyethylene, then a fiber wrap is made on top of it. Everything is fixed at the base of the plant and placed with hangers in the chosen location. For the base frame, you can use a basket made of wire, metal rods or wicker. To make it yourself, you can use the following materials:

1. Hard wire.
2. Pieces of metal-plastic pipe.
3. Unnecessary plastic arcs from a greenhouse.
4. Willow or newspaper tubes vine.
5. Wooden planks.
6. Or whatever your imagination tells you.