GPS tracker operating instructions. Power Saving Mode

GPS tracker for pets Price RUB 2,439
➡ Order - http://ali.pub/xw85k

Today we will look at a collar with a GPS tracker Tk Star Tk 909. This collar is used to track the movement of an animal. With this collar you will never lose your pet, you will be able to track its movements, and even know the history of its movements. All you need for the tracker to work is a SIM card from any operator and the presence of a GSM signal. Today you can Buy a GPS tracker Tk Star Tk 909 at a price of 2,400 rubles. Tracker dimensions 70x37x20 mm, weight 46 grams.

The collar that comes with the kit is adjustable in length from 15 to 63 centimeters.

In addition, it is possible to hang the tracker on any other collar whose width does not exceed 25 mm. These parameters allow you to use the tracker for animals weighing from 5 kg. The maximum weight of the animal is not limited - you can hang the tracker, for example, on a cow so that it does not get lost while grazing. The manufacturer has declared a moisture protection standard of IPX-6, which means that the device is protected from splashes and rain, but does not allow total immersion in water. If your dog is a fan of swimming, perhaps you should take a closer look at the waterproof GPS tracker model for monitoring the location of dogs anywhere tk 108. Tracker equipment: tracker, universal collar, Charger, instructions for English language. Instructions in Russian are available on our website: Instructions for GPS tracker Tk Star Tk 909.

On the front side of the tracker there is a button to turn the device on/off and three light indicators. The top blue indicator shows GPS operation. If the indicator is on continuously, a GPS signal is being searched. If the blue indicator blinks, the GPS signal is received and the tracker has successfully determined its location. The central indicator lights up red if charging is in progress, and goes off when the tracker is charged. The lower, green indicator shows the gprs signal. When the indicator blinks, everything is ok, the device is online. If the indicator is on, the gprs connection is not established. On the bottom side of the device there is a slot for a full-size SIM card and a charging socket.


All this is covered with a rubber plug.

The battery in this model is not removable. Battery capacity 1000 mAh - in online tracking mode, with sleep mode disabled, the tracker lasts a little more than two days. If you do not use the online tracking mode, but request coordinates via a “call” to the tracker once a day, then the tracker can last more than a month without recharging.

Settings, tracker tracking on the map, and through applications.

The tracker is configured via SMS commands. All SMS commands for setup are described in the Instructions. It is worth noting that you can use the tracker even without settings. After inserting the SIM card, we call the tracker, and in response we receive an SMS like:

The response message contains: Clickable link to Google maps. When you open it, you will see the tracker's location on Google Maps. GPS signal indication. If "V:A" is displayed? everything is ok, gps location is installed. If “V:V” is displayed, the device cannot pick up satellites and determines the location using the nearest towers mobile operator. Date and time. Device movement speed. Battery charge. Device IMEI. If you open the link from the SMS, we will see the location of the tracker:

Distinctive feature This tracker provides online tracking "Out of the box". To enable online tracking, you just need to send the SMS command “gprs 123456” to the tracker. Theoretically, the tracker involves setting up an access point (APN), as well as a username and password via SMS. But in practice (with a SIM card from MTS), everything worked without any additional settings. I assume that with SIM cards from other operators, the settings will not be needed either. Online tracking can be done through the web interface, on the website Http://2.tkstargps. net/

On the website, select Russian flag, click on “No IMEI”, below enter the IMEI of your tracker and password (default 123456). We get to the tracking page of our tracker.

The service allows you not only to track your device online, but also saves the device’s movements for a whole year! This way you can find out where the tracker was and how it moved, for example, a month ago.
As for tracker applications, you can find them at the following links: Android application IOS application Setting up the application is quite simple, and does not differ from setting up the web interface.

Through the application you can not only track the location of the device,

but also to carry out commands to configure it.

All basic settings are given exactly to those devices that are presented on our website!!

Types of tracker TK-102 (TK-102B)

The fact is that this model was originally developed by the famous Chinese manufacturer Xexun, but due to high price great popularity this tracker did not receive it, its clones coban TK-102 (TK-102B) gained much more popularity. Today, such trackers are produced by more than 5 different factories in China and Settings may vary, and this is important!!! so be careful, and if one method doesn’t work, try another, some models send their IMEI as an identifier, some 12-digit ID.

An example of setting up a tracker on the website gps-tracker.com.ua

An example of setting up a prepaid package from Kyivstar.

admin123456 +38098ххххххх

test call

coordinates

apn123456 www.ab.kyivstar.net

adminip123456 46.4.18.67 10001

If the settings you have done still fail, you can determine the device type on the main page of the site by clicking on the corresponding icon in step 4. Next, send the proposed server parameters to your tracker, and after a while the system will report the device type, server address and port and ID that your device is sending. Program this data and add the tracker to your account. You can always familiarize yourself with the range of GPS trackers on our website, which are sold by our engineers will set up for free!

A set of all SMS commands for setting up the tracker.

Initialization (Factory reset)

begin+password

Factory password: 123456

Change Password

password+old password+space+new password

password123456 666888

(you can call the tracker number 10 times and this number will be authorized automatically)

admin+password+space+phone number

admin123456 +380689924283 or admin123456 0689924283

If a control number is installed, calls from other numbers will be ignored. You can authorize up to 5 phones. numbers. The second and subsequent numbers are authorized by sending an SMS from the first number.

Removing a control number

noadmin+password+space+phone number

noadmin123456 +380689924283 or noadmin123456 0689924283

smslinkone+password

smslinkone123456 If there is no GPS signal, it will show the last coordinates

DW location coordinates

t030s005n+password

Transmission every 30 seconds. When parked, it will send 15 times and fall asleep

Data transmission interval (s-seconds, m-minutes, h-hours)

Cancel data transfer

t300s***n+password

Transmission every 30 seconds. Unlimited number of times (without falling asleep)

notn+password

Getting the location address

address+password

address123456

GPS drift suppressed (this feature is disabled by default)

suppress+password

suppress123456

suppress drift ok

Deactivating drift suppression

nosuppress+password

nosuppress123456

nosuppress ok

Enabling Audio Monitor Mode

monitor+password

monitor123456

You can call the tracker

Return to tracker mode

tracker+password

tracker123456

save030s***n+password

save030s***n123456

Transmission every 30 seconds. When parked, it will save 15 times and fall asleep

Setting up the logger by time (s-seconds, m-minutes, h-hours)

Uploading logger data

save030s005n+password

save030s005n123456

Record every 30 seconds. Unlimited number of times (without falling asleep)

load+password

If you receive an SMS “load fail! Please check GPRS” – means in this moment no GPRS connection

Uploading logger data for a certain period

load+password+space+YearMonthDay

load123456 20150125

Clearing logger memory

clear+ password

Setting up a geofence (the tracker must remain motionless for 3-10 minutes)

stockade+ password+space+latitude1, longitude1; latitude2, longitude2 (latitude1 and longitude1 are the coordinates of the upper left corner, latitude2 and longitude2 are the coordinates of the lower right corner of the square)

stockade123456 48.485000,32.216120;48.496700,32.21900

stockade+coordinates

If the border is violated, stockade will send an SMS + coordinates to an authorized number

Disabling geofencing

nostockade+password

nostockade123456

no stockade ok

Over speed

Speed+password+space+XXX (XXX speed in km/h)

123456 080 (limit 80 km/h)

If the speed limit is exceeded, it will send an SMS speed alarm to an authorized number

Cancellation of speed limit

nospeed+password

nospeed123456

cancel speed ok

Vibration sensor alarm (default this function deactivated)

schock+password

schock123456

When the sensor is triggered, you will receive an SMS “sensor alarm!+ coordinates”; this SMS, when triggered, is updated every 3 minutes (if constant movement this function is not relevant)

Deactivating the sensor alarm function

noshock+password

noshock123456

shock is deactivated

SOS button

Hold the SOS button for 3 seconds

Activation of low battery alarm.

lowbattery+password+password+on

lowbattery123456 on

If the voltage is below 3.55V, it will send 2 SMS with an interval of 15 minutes. lowbattery!+coordinates

Deactivates the low battery alarm.

lowbattery+password+password+off

lowbattery123456 off

Checking the tracker status

check+password

Battery:60% GPRS:ON GPS:ON GSM:19

IMEI check

imei+password

353535353535353

Setting the time zone (default UTC+8)

time zone+password+space+time zone

time zone123456 -6 (UTC-6)

time zone123456 5 (UTC+5)

time zone ok

APN installation

apn+password+space+APN

apn123456 www.ab.kyivstar.net (Kyivstar)

apn123456 www.mts.com.ua (MTS)

Setting IP and server port

adminip+password+space+IP address+space+PORT

adminip123456 monitoring.gps-servis.com 3339

set ip address and port ok

Cancel GPRS transmission mode

noadminip+password

noadminip123456

Activating GPRS mode

GPRS+password

Activation of SMS mode

SMS+password

reset+password

Disputes about whether the TK-102 GPS tracker is a special technical means for secretly obtaining information.

No matter how strange it may sound at first glance, but according to the legislation of Ukraine this model is considered such a means and is punishable by the criminal code under Article 359 Part 1. Many people do not even know that its organs qualify as wiretapping thanks to the microphones hidden in it. But still, the fact remains a fact and ignorance does not exempt from responsibility. The online store site strongly does not recommend using this device!

Instructions translated by the site

Instructions forGPS-trackerTK-102-2

Before starting work, make sure that you are using the instructions for the desired tracker.

This instruction is intended for TK-102 trackers; the command format is as follows:

#begin#123456# (there is a grid)

Equipment:

Specification TK102

Dimensions: 64(L)x46(W)x17(H) mm

Network: GSM/GPRS

Frequency range: 900/1800/1900MHz

GSM sensitivity: less than -102dBm

GPS chipset: SirF III chipset

GPS sensitivity: -159dBm

GPS accuracy: 5m

Cold/Hot start: 35/2sec

Charger: 110-220V input, 5V output

Car charger: 12/24V input, 5V ouput

Battery: 3.7V DC Li-Ion,800mA

Operation without recharging in continuous tracking mode: about 48 hours

Detailed description:

1) GSM and GPRS networks, the GSM receiver operates in 4 modes 850/900/1800/1900, i.e. Worldwide.

2) Powerful magnet and waterproof case.

3) Memory slot for saving coordinates when their transfer is impossible.

4) Tracking via computer / PDA / mobile phone / Google Earth or through our service.

5) When you request coordinates via SMS, you receive a link to Google maps, which can be viewed via smartphones.

6) Obtaining longitude, latitude and speed of movement in real time.

7) Automatic receipt of information at a specified interval.

8) Positioning via GPS and GSM networks. If the GPS (satellite) signal is lost, it is guided by the GSM signal.

9) High sensitivity of the GSM and GPS signal receiver.

10) Geo-fence function: the perimeter is specified by two coordinates and when you go beyond it, a notification in the form of SMS is sent to the controlling number.

11) SOS signal, low battery alert.

12) Monitoring of surrounding sounds (secret dialing via phone to the tracker with speakerphone turned on).

13) Monitoring the availability of GSM, GPRS and GPS networks, as well as battery charge (on request via SMS).

14) Two batteries 3.7V, 1000mA Li.15) Sleep mode (request coordinates only via SMS)

16) Built-in vibration sensor. 17) Small size and weight: 64 * 46 * 17mm, 50g Application:

18) Car rental.

19) Babysitting for a child/elderly person/disabled person/pet, etc.

Initialization

Send the tracker an SMS message with the text #begin#password# , it should respond “begin ok” and initialize all its settings. Default password: 123456 For example, send SMS #begin#123456# from your phone to the tracker number and wait for the response “begin ok”.

Request a tracker location with a link to a Google map

Send the SMS command #smslink#123456#, the response should be a link that can be opened on a smartphone, for example: /?q=N22.1211212,E113.080933.

Change Password

Please read this entire section carefully before changing your password!

Password setting command: #password#old password#new password#For example: #password#123456#888888#

Remember, or better yet, write down the new password. If you lose it, only flashing the tracker will help you.

Make sure that the new password consists of 6 digits, otherwise the tracker will not be able to recognize it.

make 10 calls in a row to the tracker number and get its current position. As a result of this action, the number from which the call was made will automatically be authorized.

Send an SMS with the text #admin#password#phone number# to authorize the number. For example: #admin#123456#79158888888#The response should be SMS “admin ok”. To set 2 authorized numbers, enter the command #admin#password#first phone number#second phone number#In the same way, you can set up to 5 authorized numbers.

If no number is authorized, then when you call the tracker from any number, it will respond with an SMS with its coordinates. If authorized numbers are specified, then only they will receive the tracker coordinates in response to a call.

Determining the address

Before using this function, you must set the APN of your cellular operator whose SIM card is inserted into the GPS tracker.5.8.2 After the APN is set correctly, send an SMS message to the tracker number with the text #address#password#, it will send a response with the postal address of the last identified point.

Automatic tracking

Send the command #fix#030s#005n#password# to the tracker and it will report your location 5 times with an interval of 30 seconds.

For an endless unlimited number of reports, send the command #fix#030s#***n#password#Note: the interval cannot be less than 20 seconds.

Command to stop automatic tracking: #nofix#password#

Sound monitoring (Listening to the tracker's environment)

Commands for switching between “Tracker” and “Monitor” modes: tracker and monitor.

The default mode is “Tracker”.

Send the command #monitor#password# to the tracker to enable the “Monitor” mode. The tracker should respond: “monitor ok!”. After that, you can call the tracker and listen to the sounds around it.

Send the command #tracker#password# to return to Tracker mode. If the switch is successful, the response should be: “tracker ok!”.

WITH saving coordinates

Autosave: If the GSM network signal or GPRS channel is turned off, the tracker starts saving location data and alerts to flash memory. When the GSM signal returns, all alerts will be sent to authorized numbers or to the tracking service (server). However, the saved tracker coordinates must be loaded via SMS command.5.11.2 Deleting saved data: send the command #clear#password#, it should respond “clear ok”. 5.11.3 Storage capacity: Built-in flash memory allows you to store up to 1MB of data (about 7000 coordinates). An additional card of no more than 16 MB is supported.

Vibration Alert

By default this feature is disabled. Send the command #vibrate#sensitivity level#password#. The tracker will respond “vibrate ok” if the command is accepted, and will send SMS notifications to authorized numbers when it detects any vibration. Sensitivity values: from 1 (min) to 5 (max). Command to cancel vibration alerts: #noovibrate#password#

Geo-fence

Set the boundaries of the terker's movement; when exceeded, it will send a notification to all authorized numbers.

Setting the geo-fence mode: the tracker must remain motionless for 3-10 minutes, after which send the command #stockade#password#radius#time#latitude#longitude# to set the fence boundaries. For example, the command #stockade#123456#500#60#22.312451 #113.54376#installs a fence with a radius of 500 meters with a time of 60 seconds. This means that if an object leaves this zone, an SMS message about this event will be sent after 60 seconds.

Geo-fence removal command: #nostockade#password#

Motion Alert

Installation: Send the command #move#passwrod#5.14.2 Send the command #nomove#password# to stop sending motion alerts.

Speed ​​Alert

Send the command #speed#password#speed#For example, to limit the speed to 80 km/h, send the command #speed#12345#80#The tracker will respond “speed ok!”. If the speed is exceeded 80 km/h, the tracker will send a “speed alarm” notification » to all authorized numbers.

To remove the speed limit, send the command #nospeed#password#. Note: It is not recommended to set the speed limit less than 20 km/h, otherwise the notification will be sent when the drift effect occurs.

SOS button

Hold down the SOS button for 3 seconds, this will send a message to all authorized numbers in the “SOS alarm + geo-information” format.

Low battery

Checking the tracker status

Send the command #check#password# to the tracker, it will respond with a message about its current status.

IMEI request

Send the tracker the command #imei#password#For example: #imei#12345# . In response, he will send a 15-digit serial number of the device.

Setting the time zone

Note: The default time zone is 0.

Send an SMS message in the format #time zone#password#S+hours+minutes#. For example, to set Moscow time +4, send the command: #time zome#123456#S0400# S – means the time setting code, 04 – offset in hours, 00 – offset in minutes.

Installing GPRS settings

Before using GPRS, you must send a command to set the IP address and port, and set the APN.

APN parameter values ​​should be checked with your mobile operator. At the time of writing the instructions, the APN parameters for MTS, Beeline and Megafon have the following values:

The latest tracker models understand one APN configuration command. Send the command to the tracker: #apn#password#APN-name#APN-login#APN-password# , if the installation is correct, the tracker will respond “APN OK”.

For example, to install Beeline APN, send the command #apn#123456# #beeline#beeline#

Setting the IP Address and Port Name

Send an SMS in the format #adminip#password#IP address#port number# . If the command is accepted, the tracker will respond “adminip OK”. For example, send the command #adminip#123456#222.101.150.75#9000#123456 to the tracker – tracker password 222.101.150.75 – IP address: 9000 – port number

SMS and GPRS modes

Default mode – GPRS

Send the command #noadminip#password# to the tracker, it will respond “noadminip ok” and switch to GSM mode.

Send a command with the IP address to switch to GPRS mode.

Web tracking platform

The tracker can be connected to almost any tracking system.

Platform address IP address: 202.104.150.75 Port: 9000

For tracking, you can use any of the tracking services.

You can buy GPS tracker TK-102 Here.

Instructions for GPS tracker models TK-102/102-2, TK-201/201-2, TK-206, TK-103/103-2, TK-104, TK-106/106-2, TK-107

Thank you for purchasing the GPS tracker. We sincerely hope that our product will meet all your requirements and serve you for a long time.

Before using the TK-102 GPS tracker video recorder, please read this manual carefully. The instructions contain full instructions on using a GPS tracker, including things like functionality, settings, installation recommendations, as well as specifications devices.

general information

GPS tracker TK-102 is used to monitor the location of valuables that may be stolen or lost. With its help, you can track the coordinates of a car, motorcycle, scooter, bicycle, quadcopter, luggage, and even a person or pet.

The personal tracker is designed to work in cellular networks GSM communications standard and zone of navigation satellites. The TK-102 tracker is equipped with a built-in GSM module supporting quad-GSM 850/900/1800/1900 MHz signals, which allows it to work in any network cellular communication GSM standard. If the tracker is outside the GSM network reception area, then all navigation information is saved in the internal memory (backup buffer) and transferred to the monitoring server when returning to the GSM signal coverage area.

The principle of operation is based on determining the absolute coordinates of a location on the Earth's surface (latitude, longitude) with an accuracy of no worse than 30 meters (at open area no worse than 3 meters) and transmitting data to the base station in the “short message” SMS format or to the server in GPRS format. Together with GPS coordinates, TK-102 transmits Cell ID - identifiers of cellular network cells - to the server, which allows for approximate positioning of an object even in the absence of a GPS signal (for example, if the car is in an underground garage).

The TK-102 GPS tracker has a built-in SOS button for sending alarm messages to a pre-programmed phone number.

Main features of the TK-102 GPS tracker

Modern GPS module
- Compact dimensions
- Built-in highly sensitive GPS/GSM antenna
- Support for GSM 850/900/1800/1900 MHz networks
- Built-in vibration sensor
- Support A-GPS function for quick search coordinates
- Supports communication protocols: SMS/TCP/UDP
- Ability to remotely configure the tracker using SMS commands
- Built-in tracking functions at specified intervals
- The package includes an additional cover with magnetic fastening

Application of GPS tracker TK-102

Car search, vehicle monitoring
- Search and ensure the safety of children, elderly people, animals
- Optimization of delivery services
- Security services and detectives
- Search and rescue of people in extreme sports

Appearance and controls of the GPS tracker TK-102

Sensitivity: -159dBm
- Positioning accuracy: 5 m
- Positioning time: Cold start less than 45s; After a break of less than 35s; Hot start less than 1s
- GSM/GPRS module: SIMCOM 300
- Frequency: GSM 850/900/1800/1900
- Dimensions: 64mm*46mm*17mm
- Weight: 50 grams
- Operating conditions: Temperature environment: -40С..+80С Humidity: up to 95% without condensation Altitude: up to 6000 meters
- Vibration:
- Maximum fixed speed: up to 500m/sec
- Charging mode: Automotive, input -12V, output - 5V. Standard, input 110-220V, output - 5V.
- Battery: Rechargeable Li-ion battery 3.7V, 800mAh.

Preparing for work

For devices TK-102/102-2, TK-201/201-2, TK-206: Charge battery before the first use for 5-8 hours. In the future, charging for 40-60 minutes is sufficient.

Please use the charger included with your personal tracker. A fully charged battery is enough to operate the tracker for 16-48 hours. With frequent requests to determine coordinates, the battery discharges faster; 72 hours corresponds to operation in request standby mode.

Warning:

1) Since Li-ion battery contains harmful chemical substances, please avoid damaging it, puncture it and keep it away from fire.
2) Please charge the battery in time. Complete discharge reduces service life.

It is recommended to charge the Li-Ion battery at temperatures from +5C to +40°C. It is unacceptable to charge the battery at temperatures below 0C, as this may lead to battery failure. Please note that the manufacturer's warranty does not cover the battery. Optimal temperature recharging Li-Ion batteries – from + 10°С to +40°С. It is permissible, in rare cases, to recharge the battery at a temperature of 0°C to + 10°C. The discharge (operation) temperature of a device with a Li-Ion battery is from - 10°C to +55°C.

Attention! The tracker charges only when a SIM card is inserted. If you do not use the tracker for a long time, remove the battery from it.

First, you need to insert a SIM card of any operator into the GPS tracker. The SIM card must have GPRS connected, no PIN code request and clean memory. Make sure that the number identification service is activated. Click on the tracker power button. After 10-40 seconds the device starts working and receives GSM and GPS signals. In this case, the indicator blinks with a period of 4 seconds. If your device receives GPS signals, you can start setting up.

For devices TK-103/103-2, TK-104, TK-106/106-2, TK-107: Before use, connect the device to the vehicle's operating network. Connect external GPS and GPRS antennas.

Insert a SIM card of any operator into the GPS tracker. The SIM card must have GPRS connected, no request and clean memory. Make sure that the number identification service is activated. If your device receives GPS signals, you can start setting up.

Note: Instructions and commands may vary slightly.

Tracker setup

You need to send commands via SMS to the number SIM cards, inserted into the tracker (send SMS commands without quotes):
“begin123456” is a command to reset the tracker settings (where 123456 is the default password). The response should be an SMS “Begin ok!” Issue the command “check123456” to check the battery charge, connected GPS module, etc.
Now you need to leave the tracker on open space for 10-30 minutes in order for it to capture satellites for the first time. During this time, the tracker will automatically find the network and GPS navigation satellites. If there are no signals, the LED blinks quickly, the tracker is in search mode. When the satellites and network are locked, the indicator LED flashes every 4 seconds. You can continue setting up.

By default, the TK-102 GPS tracker operates in Beacon mode, that is, it is constantly in standby mode and sends coordinates via SMS when you call the tracker. In this mode, the tracker consumes the least amount of energy and, accordingly, operates much longer (depending on the model and battery, operation in this mode can last from a week to a month).
To check, make a call to the tracker, which should receive two beeps, drop the call and send an SMS with your coordinates.

Commands for changing the provision of information in SMS modes:
“smstext123456” – in case of a call, the tracker will receive an SMS in response with the text format of the coordinates. “smslink123456” - if you call the tracker, you will receive an SMS in response with a hyperlink of coordinates to a google map.

Then you need to set up a GPRS connection (if you plan to use the device in tracking mode, with a connection to the online monitoring system)

“apn123456 mts” - specifies the required apn to configure gprs. IN in this case MTS. In response you should receive an SMS “APN ok!”; “admin123456 mts mts” - enter the login and password to set up a GPRS connection. For older versions of devices, the login and password are written in separate SMS commands: “apnuser123456 mts” and “apnpasswd123456 mts”;
“GPRS123456” - switches the tracker to GPRS mode. Alternative command "WEB123456". In response you should receive an SMS “GPRS OK!”;

Now you need to test the tracker on a gprs connection.
“adminip123456 193.193.165.167 20157” - configure the test server address for sending packets, where 193.193.165.167 is the ip address of the test service, and 20157 is the port of the test service. In response you should receive an SMS “adminip ok!”
“fix030s***n123456” - sets the message sending period to 30 seconds. For older versions of the device, the commands may have the format “t030s***n123456”.

Rip off SMS command“IMEI123456” - the response from the tracker will be: imei:306070903040498 (example). IMEI is a unique tracker id that will be required to connect to the online monitoring web service.

Now you need to go to http://id.wialon.net/ and check for a connected tracker. The name should be Xexun TK102. Next to it is your IMEI, which you received with the command “IMEI123456”.

If the device appears in the list with your IMEI (updated every 10 seconds), then all settings for the GPRS connection are correct. If the device is not in the list, you need to check all settings again.

Connecting a GPS tracker to the GPS-Trace Orange online monitoring system (http://gps-trace.com)

Brief information about the GPS-Trace Orange system.

The system allows you to use one device for free per account. The movement history is stored for the last month. The data transmitted to the GPS-Trace Orange website includes only your coordinates, speed, altitude above sea level. No other data is transferred from your device to the GPS-Trace Orange server. Accounts are deleted automatically if they are not used for more than 30 days.

To connect to the GPS-Trace Orange monitoring system, first of all you need:

Register in the system at http://gps-trace.com/?page=register
- enter Personal Area and add a new object. In the "Device type:" list, select Xexun TK-102. Tracker phone number in the format +7xxxxxxxxx. Object access password: 123456 - your default password.

In the “Unique ID:” field, enter the IMEI of your device, which you received with the command “IMEI123456”. If, when entering IMEI, you receive the message “An object with this ID already exists,” it is not possible to connect to this system. Try connecting to another online monitoring system.

Next, you will need to configure the tracker: “adminip123456 193.193.165.166 20157” - settings for trackers from the TK tracker line for the GPS-Trace Orange service. For trackers from other manufacturers, the port number may differ. Get detailed information For support for other trackers, please visit http://gps-trace.com/?page=hw

Note: The GPS-Trace Orange satellite monitoring system can be used from your mobile phone. Login mobile version produced at: http://mobile.gps-trace.com/. To start using it, you need to activate mobile access in your profile settings.

Connecting a GPS tracker to the online monitoring system GPShome.ru (http://www.gpshome.ru)

Brief information about the GPShome.ru system

The system allows you to use 3 devices for free in one account. The movement history is stored behind last 24 hours. The data transmitted to the site includes only your coordinates, speed, altitude above sea level. Fuel consumption can be adjusted. No other data is transferred from your device to the GPShome.ru server.

To connect to the GPShome.ru monitoring system you must:

Register in the system at http://map.gpshome.ru/main/register.php
- log into your personal account and add a new object.
In the "Device type:" list, select Xexun TK-102. Tracker phone number in the format +7xxxxxxxxx. In the “Unique ID:” field, enter the IMEI of your device, which you received with the command “IMEI123456”.

Next you will need to configure the tracker:
“adminip123456 213.219.245.116 20100” - settings from the TK tracker line for the GPShome.ru service. For trackers from other manufacturers, the port number may differ. You can get detailed information about support for other trackers on the page http://www.gpshome.ru/gpshome_connect

Note: The GPShome.ru satellite monitoring system can be used from your mobile phone. Login to the mobile version is at: http://ww.gpshome.ru/m

Connecting a GPS tracker to the online monitoring system GPS-tracker.com.ua (http://gps-tracker.com.ua)

Brief information about the GPS-tracker.com.ua system

The system allows you to use up to 5 devices for free in one account. The movement history is stored for the last 180 days. The data transmitted to the site includes only your coordinates, speed, altitude, fuel level sensor. No other data is transferred from your device to the GPS-tracker server on a free account.

To connect to the GPS-tracker.com.ua monitoring system you must:

Register in the system at http://gps-tracker.com.ua/index.php
- log into your personal account and add a new object.
In the "Device Type:" list, select Xexun TK-102 or TK-106. Tracker phone number in the format +7xxxxxxxxx. In the “Unique ID:” field, enter the IMEI of your device, which you received with the command “IMEI123456”.

For other models, it is worth trying the first setting option first. More information about supported devices can be found on the page http://gps-tracker.com.ua/connection.php

Note: Satellite monitoring system GPS-tracker.com.ua. can be used from your mobile phone. Login to the mobile version is made at: http://m.gps-tracker.com.ua

SMS commands for TK family trackers.

Frequently used commands for TK family trackers.

“check123456” - displays the battery charge level, signal level, enabled modules, etc.
“admin123456 +7xxxxxxxxxx” – sets the phone number from which only control is possible. There are 5 numbers available for installation.
“noadmin123456 +7xxxxxxxxxx” - Delete an authorized number.
“password123456 654321” – change the standard password. (123456 in this case is the old password, 654321 is the new password) For correct operation, use only 6 characters. Russian language cannot be used.
“smstext123456” – in case of a call, the tracker will receive an SMS in response with text coordinates format.
“smslink123456” - if you call the tracker, you will receive an SMS in response with a hyperlink of coordinates to a google map.
“noadminip123456” – disable GPRS operating mode.
“speed123456 080” - speed control. If the speed is exceeded 80 km/h, the tracker will send a message to all authorized numbers. Next, the tracker will check the speed every 10 minutes and signal if it is exceeded.
“move123456” - “auto theft” mode. If movement starts, the tracker will send an SMS to all authorized phone numbers. Disabling the mode with the “nomove123456” command. Deactivation is not possible after starting to move
“SMS123456” – switch from GPRS mode to SMS mode.
“tracker123456” – switch from SMS mode to GPRS mode.
“monitor123456” – switch to listening mode. When you call, the tracker picks up the handset and connects a microphone for listening. “adminpassword13142324” - password reset

Initialization (Factory reset)
begin+password
begin123456
begin ok
Factory password: 123456

Change Password
password+old password+space+new password
password123456 666888
password OK
Password must be 6 digits

Control number authorization
(you can call the tracker number 10 times and this number will be authorized automatically)
admin+password+space+phone number
admin123456 +380689924283 or admin123456 0689924283
admin ok
If a control number is installed, calls from other numbers will be ignored. You can authorize up to 5 phones. numbers. The second and subsequent numbers are authorized by sending an SMS from the first number.

Removing a control number
noadmin+password+space+phone number
noadmin123456 +380689924283 or noadmin123456 0689924283
no admin ok

Motion Sensor. The tracker has a built-in motion sensor. To install a motion sensor, you need to send an SMS with the command: shake+password+space 1-10 (1 - high sensitivity, 10 - low)

Request a location with a link to a map Google maps
smslinkone+password
smslinkone123456
In response, the tracker will send an SMS with a link to a Google map like: http://maps.google.com/maps?f=q&hl=en&q=49.446297,32.039862& speed: 000.0 18/04/10 17:50 L:3.68V Signal:F imei: 354776031555474. Open the link in your phone browser and see the location of the tracker on Google map maps. If there is no GPS signal, it will show the latest coordinates

Auto location report mode
Data transmission interval (s-seconds, m-minutes, h-hours)
t030s005n+password
- where 030 - interval 30, s - seconds, m - minutes, h - hours, 005 - number of reports, that is, the tracker after this command sends 5 reports with an interval of 30 seconds. For example: t015m010n - 10 reports with an interval of 15 minutes. When parked, the TK-102 GPS tracker will send 15 times and go into energy saving mode.
t030s***n+password - programming an automatic report without limiting the number of reports (in the example given, the tracker will send a location report every 30 seconds without limiting the number and time.)
To stop the auto-report, a message is sent to the tracker: notn+password

Cancel data transfer
t300s***n+password
t300s***n123456

Transmission every 30 seconds. Unlimited number of times (without falling asleep)
notn+password
notn123456

Getting the location address
address+password
address123456

GPS drift suppressed (this feature is disabled by default)
suppress+password
suppress123456
suppress drift ok

Deactivating drift suppression
nosuppress+password
nosuppress123456
nosuppress ok

Enable audio monitor mode. After calling the tracker, you will hear what is happening near the tracker.
monitor+password
monitor123456
monitor ok

Tracking mode (positioning)
Return to tracker mode. After calling the tracker, it will transmit its coordinates.
tracker+password
tracker ok

Setting up the logger by time (s-seconds, m-minutes, h-hours)
save030s***n+password
save030s***n123456
save ok

Transmission every 30 seconds. When parked, it will save 15 times and fall asleep
Setting up the logger by time (s-seconds, m-minutes, h-hours)
Uploading logger data
save030s005n+password
save030s005n123456
save ok

Record every 30 seconds. Unlimited number of times (without falling asleep)
load+password
load123456
load ok

If you receive an SMS “load fail! Please check GPRS” – means there is no GPRS connection at the moment
Uploading logger data for a certain period
load+password+space+YearMonthDay
load123456 20150125
load ok

Clearing logger memory
clear+ password
Clear123456
clear ok

Setting up a geofence (the tracker must remain motionless for 3-10 minutes).
stockade+ password+space+latitude1, longitude1; latitude2, longitude2 (latitude1 and longitude1 are the coordinates of the upper left corner, latitude2 and longitude2 are the coordinates of the lower right corner of the square)
stockade123456 48.485000,32.216120;48.496700,32.21900
stockade+coordinates

If the border is violated, stockade will send SMS + coordinates to an authorized number

Disabling geofencing
nostockade+password
nostockade123456
no stockade ok

Over speed
Speed+password+space+XXX (XXX speed in km/h)
speed
123456 080 (limit 80 km/h)

If the speed limit is exceeded, it will send an SMS speed alarm to an authorized number
Cancellation of speed limit
nospeed+password
nospeed123456
cancel speed ok

Vibration sensor alarm (this function is disabled by default)
schock+password
schock123456
schock ok

When the sensor is triggered, you will receive an SMS “sensor alarm!+ coordinates”; this SMS is updated every 3 minutes when triggered (if you are constantly moving, this function is not relevant)
Deactivating the sensor alarm function
noshock+password
noshock123456
shock is deactivated

SOS button
When you press the button for 3 seconds, until the signal light stops blinking frequently, the tracker sends a help message with coordinates to all authorized numbers: help me + coordinates. A message will be sent every 3 minutes.
To stop, you need to send a reply SMS from any authorized number to the tracker with the command help me!

Activation of low battery alarm.
lowbattery+password+password+on
lowbattery123456 on
If the voltage is below 3.55V, it will send 2 SMS with an interval of 15 minutes. lowbattery!+coordinates
Deactivates the low battery alarm.
lowbattery+password+password+off
lowbattery123456 off

Checking the tracker status
check+password
check123456
Battery:60% GPRS:ON GPS:ON GSM:19

IMEI check
imei+password
imei123456
353535353535353

Setting (default UTC+8)
time zone+password+space+time zone
time zone123456 -6 (UTC-6)
time zone123456 5 (UTC+5)
time zone ok

APN installation
apn+password+space+APN
apn123456 www.ab.kyivstar.net (Kyivstar)
apn123456 www.mts.com.ua (MTS)
set APN OK

Setting IP and server port
adminip+password+space+IP address+space+PORT
adminip123456 monitoring.gps-servis.com 3339
set ip address and port ok

Cancel GPRS transmission mode
noadminip+password
noadminip123456

Activating GPRS mode
GPRS+password
GPRS123456
GPRS ok

Activation of SMS mode
SMS+password
SMS123456
SMS ok

Power Saving Mode

Power saving mode for GPS, without saving on the GSM module: in this mode, after positioning, the tracker turns off the GPS module until the next SMS request. In this mode, the approximate consumption is about 20 mA.

Energy saving mode for GPS and GSM modules: in this mode, the tracker turns off the GPS module, and GSM module goes into standby mode. Consumption in this mode is about 10 mA. The tracker only responds to a direct phone call.

The energy saving mode is set by the tracker after initialization with a long absence of requests (more than 10 minutes), and minimal settings, namely, the following functions are not installed: Geo-fence, Parking, Speed ​​control, Auto location report, GPRS mode is disabled.

In energy saving mode, the tracker can wait for a request for up to 48 hours.

Precautionary measures

Keep the TK-102 tracker dry. Any liquid that gets inside can damage electronic circuit device.
- Do not use or store the tracker in dusty places.
- Do not place the tracker in places with high or extremely low temperatures.
- Use the tracker with caution. Do not subject to shock or severe vibration.
- Clean the tracker with a dry cloth. Do not use chemicals and solvents.
- Do not paint the tracker as this may damage some external parts.
- Do not disassemble the tracker.
- Please use the standard charger and battery. Other types may harm the tracker.

Possible malfunctions and their correction

Does not turn on - Check the battery charge and that it is installed correctly. No response to request - You may be requesting a tracker from an unauthorized phone number. Reset settings. Complete the initialization and authorize your phone number.

When determining, the tracker does not provide coordinates - The tracker is not visible to satellites. Start using the tracker (first turn on after purchase) in conditions of good visibility of the open sky.

Note:

SMS messages to the tracker must be sent to text format regardless of lowercase and uppercase letters, the PDU format is not identified.

The first turn on of the tracker must be carried out on the site under open air. This will help the tracker quickly install all navigation satellites and will subsequently significantly reduce their search during positioning, as well as the accuracy of determining coordinates. The tracker program uses the satellite position memory and, if the satellite is visible enough, indicates the exact direction to search for satellites.

Appearance of TK-102

Front and back

Top and bottom view

Side

Internal organization

Installing a SIM card in the GPS tracker TK-102

Open the back cover of the tracker, remove the battery and install the SIM card, as shown in the diagram:

Battery and charging

When using for the first time, charge the battery for 8-12 hours. In the future, 3-5 hours will be enough to fully charge the battery. Use the battery and charger that came with the tracker! The standby time is 48 hours; during active use, the battery discharges faster.

Turning on the GPS tracker TK-102

1) Insert the battery and SIM card into the device

2) The GPS tracker will turn on automatically after installing the SIM card and charged battery

3) Within 10-40 seconds, the GPS tracker will establish a connection with GPS satellites and GSM network. After this, the indicator will start flashing every 4 seconds. If the indicator is constantly on, the connection has not yet been established.

4) Once the connection to the satellites and GSM network is established, you can continue setting up

Initialization

Before you start setting up the TK-102, you must undergo initialization.
Send an SMS to the number of the SIM card installed in the tracker in the following format:

begin+user password.

The default password is 123456. If initialization was successful, you will receive a response message from the tracker “begin ok”

Changing the service password

To change the service password (the default service password is 123456), send the command in the form:

password+old password+space+new password

Note:

1) Don't forget the service password! To recover your password, you will have to download special software.

2) Make sure that the length of the new password is 6 digits, otherwise the GPS tracker will not be able to recognize it

Setting up control phone numbers

To control the TK-102 GPS tracker, receive messages from it, etc. must be entered into its memory
phone numbers (authorize phone numbers of tracker users) with
which will be managed and to which data and notifications will be sent
from the tracker.
You can authorize up to 5 numbers.

1) Call the tracker number 10 times and your phone number will be authorized automatically

2) Adding a new number can also be done by sending an SMS message in the following format:

admin+user password+space+phone number

Successful addition of a number is confirmed by a message from the tracker: "admin ok!"
Subsequent numbers are authorized by sending an SMS with first issue.

noadmin+user password+space+phone number to be deleted

Request coordinates via SMS

To receive an SMS message with coordinates from the tracker, you need to call it from your mobile phone, and the message will be sent to the caller's number.

Lat: - latitude

Long: - longitude

Speed- speed

DD/MM/YY HH:MM- date and time

bat- battery charge level (F - Full, L-Low low)

Signal- signal level (F - Full) imei - imei number of the GPS tracker

Automatic location reporting mode

In this mode, the device sends SMS messages with information about the position of the object to the control number at specified intervals

An SMS in the following format is sent to the tracker:

t030s005n+user password

Where 030 (3 digits, maximum value = 255) - interval 30, s - seconds, m - minutes, h - hours, 005 -
number of reports, that is, the tracker after this command will send 5 reports at intervals
in 30 seconds.
For example: t015m010n123456 - 10 reports with an interval of 15 minutes.
To program an automatic report without limiting the number of reports, an SMS in the following format is sent to the tracker:

t030s***n+user password,

in the example given, the tracker will be every 30 seconds

send a location report without limiting the number of requests

To stop auto-reporting, a message is sent to the tracker notn+user password

Note: the interval between reports cannot be less than 20 seconds

Configuring tracker behavior for incoming calls

The TK-102 tracker can respond to an incoming call in 2 ways:

1) Send SMS messages with the coordinates of the object to the caller’s number or authorized phone numbers (if it is in tracking mode)

2) “Pick up the phone” and let you listen to the situation near the device (listening mode)

By default, tracking mode is set. To activate listening mode you need to send a message: monitor+user password

To return to tracking mode again, send a message:
tracker+user password

"Electronic fence"

In the “Electronic fence” mode, the coordinates of the upper left and lower right points of the area surrounded by the “electronic fence” are specified. When the “electronic fence” mode is turned on, if the tracker leaves the area limited by the “electronic fence”, it sends the current coordinates to the control phone numbers. If the device is already moving outside the “fenced” area, this function will be inactive.

Command Format: stockade+user password+space+latitude1,longitude1;latitude2,longitude2

latitude1, longitude1 - coordinates of the upper leftmost point of the site.

latitude2, longitude2 - coordinates of the lowest right point of the site.

Disabling the "electronic fence": nostockade+user password

Overspeed control

If the tracker speed exceeds the programmed speed, it
sends a message to authorized numbers.
Send an SMS to the tracker in the following format:

speed+user password+space+speed limit

speed123456 080 - for speed limit 80km/h

To remove the speed limiting function, send an SMS in the following format:

nospeed+user password

When speeding, the tracker sends a message to authorized numbers
of the following form: speed+speed limit!+information about coordinates. Next the tracker will be
check the speed every 10 minutes and signal if it is exceeded.

Notification of the start of movement

The function allows you to receive a signal from the tracker when you start moving.

The function is installed by sending an SMS in the following format:

move+user password

The function is deactivated by sending an SMS to the tracker in the following format: nomove+user password
Deactivation is not possible once the vehicle has started moving.
Tracker message when starting movement move!+coordinates

SOS button

When you press the SOS button for 3 seconds, the tracker sends a message about help with coordinates to everyone
authorized numbers: help me + object coordinates. A message will be sent every
3 minutes. To stop, you need to send a reply from any authorized number
SMS to the tracker with the command "help me!"
In response, the tracker will send a notification “Help me ok!” and stop sending messages

Low battery alarm

The function is set at the factory. When the battery is discharged, when the voltage becomes less than 3.7V,
the tracker notifies authorized numbers about this in the following form: battery+coordinates
The message repeats every 30 minutes until the battery is charged.

Setting GPRS mode

To switch the tracker to GPRS mode, you need to make the following settings:

1. Determine Internet access point in accordance with the settings of the mobile operator whose services you will use. To do this, you need to send an SMS to the tracker with the command:

apn+user password+space+access point address

For the cellular operator MTS, the SMS will be as follows: apn123456 internet.mts.ru

Login for access point:

apnuser+user password+space+APN login.

For the mobile operator MTS, the SMS will look like this: apnuser123456 MTS

Access point password:

apnpasswd+user password+space+access point password

For the cellular operator MTS, the SMS will be as follows: apnpasswd123456 MTS

2 . To transfer data from the tracker to the server, which will process the received information, you must specify the server IP address and port number:

adminip+123456+space+IP address+space+port

For example, for the MasterTracking GPS monitoring system, the SMS will be as follows: adminip123456 188.40.125.149 4450

To refuse data transfer in GPRS mode, send an SMS in the following format:

noadminip+user password

How to find out the IMEI of the Xenun TK-102 GPS tracker?

Send the command: imei+user password In response you will receive an SMS with a 15-digit tracker imei number