DIY Christmas tree craft from a bottle. DIY Christmas tree: master class with photos on how to make a Christmas tree yourself. Algorithm for doing the job

Below should be the most large bottles(2 and 1.5 liter bottles, in the middle there are liter bottles, and at the top there are 0.5 and 0.3 liter bottles. If you have bottles of the same volume, then adjust the length of the “branches” yourself by cutting the strips to the desired length.

Make a hole in the left bottom, which you secure to the lower end of the stick using a plastic bottle cap (you can hammer a nail in for strength).

Place the last, smallest piece, neck up, on the upper end of the stick and screw the green plug onto the neck, also securing it with a nail for strength.

A little patience, perseverance, diligence and forest beauty ready!

Such Christmas trees can be used as New Year's decoration your houses!

Method 2. To make such a Christmas tree you need a minimum of time and expense. Master class on making a Christmas tree from plastic bottles, will tell you in detail how to make such an original New Year’s craft.

To make a decorative New Year's craft: a Christmas tree from plastic bottles, you will need the following:

1. Plastic bottles - 3 pcs;
2. Scotch;
3. Sheet thick paper, ideally whatman paper (A4);
4. Scissors;

Method 3. And finally last option for today - a Christmas tree made from plastic milk bottles (what decorative New Year trees are not made from...). The design is completely collapsible, has the maximum resemblance to the original, does not require particularly complex technologies or specific work skills, there are no problems with bottles either, and a holiday is just around the corner...

Materials and tools

The material for making the Christmas tree is a milk plastic bottle or part of it (Fig. 1). To make a homemade tabletop Christmas tree, you will need 5-20 milk/kefir plastic bottles with corrugation at the bottom. The number of bottles determines the number of branches and tiers. The more branches, the more fluffy the Christmas tree is; the more tiers, the taller it is.

In addition to bottles, you only need scissors and plastic rivet technology

Plastic rivets

To implement the technology of plastic rivets, it is necessary to have a means for melting (installing) the rivets and the rivet itself. You need to manage to melt the head of the rivet using a hot nail or lighter. You can do this in the same way with a well-heated soldering iron. In addition, you will need clamps and tweezers to install rivets in hard to reach places.

For plastic rivets, it is very important to choose the material. After fluttering around for about a year, through trial and error, taking into account the requirements of strength and availability, I identified several sources for obtaining plastic rivets:

1. Empty rods from ballpoint pens. Enough available material. They are good because they are colorless and the compound, with their help, turns out to be organically integrated into the product made from plastic bottles. Such a rivet turns out neat, with a round head, however, it has a slightly reduced tensile strength. In addition, the rod from ballpoint pens is round in cross-section and completely fills the drilled hole in the parts being connected. By the way, the walls of the rods are different thicknesses, for rivets it is better to use rods with thicker walls.

2. Chupa Chups sticks. Similar to option No. 1 only in color. The connection is more cumbersome, and the rivet head melts with difficulty (it either burns, becomes ugly, or unreliable).

3. The most perfect option, and very convenient (I give the world a suggestion) to use material from buckets with construction mixtures for 3, 5, 10 liters There are quite a lot of them left after repairs, and even one lasts for a long time.

From the walls of such a bucket you need to cut a ring, and cut the ring along the generatrix (this is the only way to do it) into strips 2...4 mm wide, length from 4 to 15 cm. These will be the blanks for rivets, and the best and most affordable, practically in unlimited quantity.

Obtaining a connection using such rivets is simple. It is more convenient for this to prepare rivets of the required length in advance, melting the head of the plastic rod on one side. To connect two parts with plastic rivets, we overlap the parts, melt them with the same burner, forming a hole of the required profile and size, insert the rivet there and, by melting, form a head from the opposite end of the rivet rod. After practicing reflowing several times, the head turns out neat and tear-resistant.

Let's get started...

To implement the idea it is necessary raw material in the form of a part of a milk plastic bottle (Fig. 1a) which is cut along the circumference into two components (Fig. 2 and Fig. 3, respectively). A trunk will be formed from the part adjacent to the neck (Fig. 1b), and branches of the future New Year tree will be cut out from the ring with a central groove (Fig. 1c). One whole plastic bottle produces two or three rings. The more rings you prepare, the fluffier and taller the Christmas tree you can assemble. I had at least 20 of these rings (10 full bottles).

Plastic rings with a groove in the middle need to be cut into several equal parts(Fig. 2) along the generatrices of the bottle cylinder. As a result, we get convex rectangles. If you cut into 2 parts, then from such long halves you will get long lower branches of the Christmas tree, if you cut into 3 equal parts, you will get branches of medium tiers and medium length, and by cutting into 4-5 parts, you get small blanks for the upper tiers of a tabletop Christmas tree . It is not at all necessary to observe particular uniformity in the dimensions of the rectangles for one type of tiers.

Next begins the rather tedious work of forming the branch. From each plastic convex rectangle (Fig. 3a), a wedge-shaped blank should be cut out with scissors (Fig. 3b). The axis of symmetry of the wedge-shaped part should be located along the corrugation groove. Immediately after cutting the workpiece, “needles” should be formed on it, making cuts along the side edges at approximately 45 degrees to the groove and radially at the end of the “branch”. (Fig. 3c). The needles are alternately moved out from the plane of the workpiece, also at 45 degrees to each other. Placing the needles up and down relative to the plane of the branch provides fluffiness to the Christmas tree.

As a result of such painstaking work, several sets (Fig. 4) of branches are obtained different sizes for a desktop homemade Christmas tree. Cutting out branches and then needles is quite a long task, but you can entrust this to your family as part of a collective creativity in decorating life for the New Year. It should be noted that it is difficult to accurately determine the number of branches forming a specific tier by eye, so you should always have several rings in stock (Fig. 1c) for cutting branches during the installation of tiers

The place for attaching branches is the trunk, which consists of several parts (logs). The top parts of plastic bottles (Fig. 1b) were considered waste during the separation of the rings (Fig. 1c), but now they are also used in tree making to create a trunk. The base of the trunk and the lower log is the full neck part of a plastic bottle (Fig. 5a). The upper logs are assembled from blanks obtained by cutting off the threaded part of a milk bottle with a flange, as well as removing a segment of plastic along the generatrices (Fig. 5b, 5c). The segments need to be rolled into a tube and secured on both sides with plastic rivets. In a similar way, it is necessary to create several logs to attach tiers of branches. In my case, these are 3 logs, but there could be more or less. For a miniature Christmas tree, 3-4 tiers of branches on just one log are enough.

Naturally, the diameter of the trunk should taper towards the top of the tabletop tree and the diameter of the upper log should be smaller than the lower one. The larger the cut of the segment, the higher the log obtained from the conical top of the plastic bottle. For the top you need a half segment, and for the middle part about two-thirds of the whole neck (Fig. 5b). The diameter of the lower hole of the upper log should be approximately 1 mm larger than the upper hole of the lower log forming the trunk.

It's time to attach the branches to the "logs". Each log will need to place 2-3 tiers of branches. The small number of tiers does not allow effectively covering the rivet heads with branches, and a large number of spoils the aesthetic appearance of the Christmas tree. In each tier of this design you can install from 4 to 10 branches. Fastening is carried out using plastic rivets, since you will need quite a lot of plastic rivets, it is better to prepare them for future use. The easiest way is to place the branches in tiers on the lower logs (Fig. 6), since the neck of the plastic bottle is wide enough and it is convenient to hold the plastic rivet with inside finger.

If you place the branches closely along the circumference of the tier, then one rivet is enough to attach the branch to the trunk (Fig. 6-8). For those who like greater reliability, they can install two rivets side by side. The tiers of branches must be formed like the roof deck of a house - from the bottom up, then the branches of the upper tier will cover the rivets of the lower one and the heads of the rivets will be completely invisible.

In my case, in the lower (Fig. 6) and middle (Fig. 7) log of the trunk there are 2 tiers of branches, and in the upper one - 3 (Fig. 8). There are 5 tiers of branches in total. It’s quite enough to look amazingly similar to a real tree. Installation of plastic rivets on upper tier, due to its small diameter, should be done using tweezers or a medical clamp.

After securing all tiers on all logs, you can begin final assembly. But first it is advisable to decide on the top. In my case, without thinking for a long time, I built the top using the same technology as the trunk (Fig. 5), that is, by rolling the plastic into a cone. But you can do this in another way, for example, in the form of an asterisk or a ball (I like the cone better). The top of the tree is attached to top element the barrel also using a rivet installed from the inside and melted from the outside. The upper part of the trunk, together with the top, is itself a miniature tabletop Christmas tree (Fig. 9). You can install it on your monitor and enhance the holiday feeling...

A living Christmas tree grows from the bottom up, in the same order, and we collect logs with tiers of branches by adding “logs” (Fig. 10) to the already existing Christmas tree. It is better to connect the trunk elements together in a place covered by a branch, at three points along the circumference of the trunk. In this case, the trunk becomes rigid and will not break if the Christmas tree accidentally falls to the floor from the table, the Christmas tree is a tabletop one...

And if you insert a dynamic light part (for example, a garland) inside the Christmas tree, then on New Year’s Eve it will amaze those around you with its charm:

Here is such a master class. Of course, it’s a little complicated, but what a beauty it turns out!

Today we bring to your attention the process of making a large holiday tree from simple green plastic bottles. This Christmas tree is collapsible, so it can have any number of tiers (you only need a longer “stem”). You can add more layers each year and within a few years you will get a big fluffy beauty around which your children will dance in circles.

To make a Christmas tree from plastic bottles you need:

Green plastic bottles (it took 1.3 liter bottles about 30 pieces);

Steel part (“rod”) of the desired length (here about 0.5 m, with an approximate diameter of 0.5 cm);

Single-core aluminum wire insulated (section 2.5mm2);

Christmas tree stands;

Scissors, heat gun;

Christmas tree made from plastic bottles step by step:

Take the bottle and cut off the middle part from it, as in photo 2-3. Then cut this part bottles in a spiral using scissors, cut a strip with an approximate width of about 2 centimeters (photo 4).

Next, you need to bend one edge approximately 0.5 cm along the entire length of the strip, as in photo 5-6. This side will help set the direction for spruce needles (needles), and will also serve as a limiter for cutting the “needles”. Cut a fringe strip about 0.1 cm wide (photo 7-8).

Then start creating spruce branches. Let's make a “top” for the Christmas tree, for which wrap a strip of plastic (about 8 cm long) around the “rod” and glue it using a hot-melt gun (apply glue to the “rod”, otherwise the workpiece will high temperature may become deformed) (photo 9). Next, twist a small piece of fringe and glue the pieces inside (photo 10). Then wrap the “rod” in a spiral with a strip of fringe (photo 11). When one strip ends, take another and continue gluing (photo 12-13).

After making the top, make the first tier of branches, which will consist of three short parts (a branch with an approximate length of about 7-8 cm). Make a wire frame, as shown in photo 14, connect it to a plastic ring (photo 15-16).

Start wrapping the “branches” in the same way as the top (photo 17). After creating all the branches, braid the “needles” and the main stem (photo 18-19). As a result, you should get two parts, as in photo 20.

Make the third detail of the future Christmas tree, a remote one. At first it was made too high, so it was moved to the bottom of the tree and the piece was made smaller. In total, four distances were used for this tree: Upper - approximately 0.5 cm; the second - about 0.6 cm; third - 7 cm; lower - 8 cm. Make “distances” by analogy with making the crown, just do not close the upper hole (photo 21). The Christmas tree will look like at this stage, as in photo 22.

Next, make a second tier of branches, which will be wider than the first and will already include four branches (with an approximate length of about 9 cm), each of which will have two side branches. The length of the main branches turned out to be approximately 9 cm (photo 23 -24).

Wrap the frame, starting with the smallest branches, then the main ones, and ending with the trunk (photo 25-26). Under the influence of hot glue, the plastic heats up and takes on a fairly plastic shape, making it very easy to set the direction of the needles for each branch at the junction of the branches (photos 27-29).

The central part of the stem before camouflage with pine needles looks like in photo 30, and after camouflage it looks like in photo 31. Next you need to make the second spacer part (photo 32).

This is followed by the production of the third tier, with an approximate length of branches of about 10 cm (20 cm in diameter) (photo 33). Finally, make the lower tier (branches 15 cm long (30 cm in diameter)) and the lower distance (photo 34).

All that remains is to install everything on the stand! If desired, you can make any number of tiers, and each subsequent tier should be proportionally wider than the previous one - this way you can get a tall and elegant Christmas tree.

The Christmas tree made from plastic bottles is ready!

According to the site: girlsschool.ru

At the bottom there should be the largest bottles (2 and 1.5 liters, in the middle - liter bottles, and at the top 0.5 and 0.3 liter bottles. If you have bottles of the same volume, then adjust the length of the “branches” yourself by cutting strips to the desired length.

Make a hole in the left bottom, which you secure to the lower end of the stick using a plastic bottle cap (you can hammer a nail in for strength).

Place the last, smallest piece, neck up, on the upper end of the stick and screw the green plug onto the neck, also securing it with a nail for strength.

A little patience, perseverance, effort and the forest beauty is ready!

These Christmas trees can be used as New Year's decorations for your homes!

Method 2. To make such a Christmas tree you need a minimum of time and expense. A master class on making a Christmas tree from plastic bottles will tell you in detail how to make such an original New Year's craft.

To make a decorative New Year's craft: a Christmas tree from plastic bottles, you will need the following:

1. Plastic bottles - 3 pcs;
2. Scotch;
3. A sheet of thick paper, ideally whatman paper (A4);
4. Scissors;

Method 3. And finally, the last option for today is a Christmas tree made from plastic milk bottles (what decorative New Year trees are not made from...). The design is completely collapsible, has the maximum resemblance to the original, does not require particularly complex technologies or specific work skills, there are no problems with bottles either, and a holiday is just around the corner...

Materials and tools

The material for making the Christmas tree is a milk plastic bottle or part of it (Fig. 1). To make a homemade tabletop Christmas tree, you will need 5-20 milk/kefir plastic bottles with corrugation at the bottom. The number of bottles determines the number of branches and tiers. The more branches, the more fluffy the Christmas tree is; the more tiers, the taller it is.

In addition to bottles, you only need scissors and plastic rivet technology

Plastic rivets

To implement the technology of plastic rivets, it is necessary to have a means for melting (installing) the rivets and the rivet itself. You need to manage to melt the head of the rivet using a hot nail or lighter. You can do this in the same way with a well-heated soldering iron. In addition, you will need clamps and tweezers to install rivets in hard-to-reach places.

For plastic rivets, it is very important to choose the material. After fluttering around for about a year, through trial and error, taking into account the requirements of strength and availability, I identified several sources for obtaining plastic rivets:

1. Empty ballpoint pen refills. Fairly accessible material. They are good because they are colorless and the compound, with their help, turns out to be organically integrated into the product made from plastic bottles. Such a rivet turns out neat, with a round head, however, it has a slightly reduced tensile strength. In addition, the rod from ballpoint pens is round in cross-section and completely fills the drilled hole in the parts being connected. By the way, the walls of the rods come in different thicknesses; for rivets it is better to use rods with thicker walls.

2. Chupa Chups sticks. Similar to option No. 1 only in color. The connection is more cumbersome, and the rivet head melts with difficulty (it either burns, becomes ugly, or unreliable).

3. The most ideal option, and very convenient (I give the world a proposal) is to use material from buckets with construction mixtures of 3, 5, 10 liters. There are quite a lot of them left after repairs, and one lasts for a long time.

From the walls of such a bucket you need to cut a ring, and cut the ring along the generatrix (this is the only way) into strips 2...4 mm wide, length from 4 to 15 cm. These will be the blanks for rivets, and the best and most affordable, in almost unlimited quantities quantity.

Obtaining a connection using such rivets is simple. It is more convenient for this to prepare rivets of the required length in advance, melting the head of the plastic rod on one side. To connect two parts with plastic rivets, we overlap the parts, melt them with the same burner, forming a hole of the desired profile and size, insert the rivet there and, by melting, form a head from the opposite end of the rivet rod. After practicing reflowing several times, the head turns out neat and tear-resistant.

Let's get started...

To implement the idea, a source material is required in the form of a part of a plastic milk bottle (Fig. 1a), which is cut along the circumference into two components (Fig. 2 and Fig. 3, respectively). A trunk will be formed from the part adjacent to the neck (Fig. 1b), and branches of the future New Year tree will be cut out from the ring with a central groove (Fig. 1c). One whole plastic bottle produces two or three rings. The more rings you prepare, the fluffier and taller the Christmas tree you can assemble. I had at least 20 of these rings (10 full bottles).

Plastic rings with a groove in the middle need to be cut into several equal parts (Fig. 2) along the forming elements of the bottle cylinder. As a result, we get convex rectangles. If you cut into 2 parts, then from such long halves you will get long lower branches of the Christmas tree, if you cut into 3 equal parts, you will get branches of medium tiers and medium length, and by cutting into 4-5 parts, you get small blanks for the upper tiers of a tabletop Christmas tree . It is not at all necessary to observe particular uniformity in the dimensions of the rectangles for one type of tiers.

Next begins the rather tedious work of forming the branch. From each plastic convex rectangle (Fig. 3a), a wedge-shaped blank should be cut out with scissors (Fig. 3b). The axis of symmetry of the wedge-shaped part should be located along the corrugation groove. Immediately after cutting the workpiece, “needles” should be formed on it, making cuts along the side edges at approximately 45 degrees to the groove and radially at the end of the “branch”. (Fig. 3c). The needles are alternately moved out from the plane of the workpiece, also at 45 degrees to each other. Placing the needles up and down relative to the plane of the branch provides fluffiness to the Christmas tree.

As a result of such painstaking work, several sets (Fig. 4) of branches of different sizes are obtained for a desktop homemade Christmas tree. Cutting out branches and then needles is quite a long task, but you can entrust this to your family as part of a collective creativity in decorating life for the New Year. It should be noted that it is difficult to accurately determine the number of branches forming a specific tier by eye, so you should always have several rings in stock (Fig. 1c) for cutting branches during the installation of tiers

The place for attaching branches is the trunk, which consists of several parts (logs). The top parts of plastic bottles (Fig. 1b) were considered waste during the separation of the rings (Fig. 1c), but now they are also used in tree making to create a trunk. The base of the trunk and the lower log is the full neck part of a plastic bottle (Fig. 5a). The upper logs are assembled from blanks obtained by cutting off the threaded part of a milk bottle with a flange, as well as removing a segment of plastic along the generatrices (Fig. 5b, 5c). The segments need to be rolled into a tube and secured on both sides with plastic rivets. In a similar way, it is necessary to create several logs to attach tiers of branches. In my case, these are 3 logs, but there could be more or less. For a miniature Christmas tree, 3-4 tiers of branches on just one log are enough.

Naturally, the diameter of the trunk should taper towards the top of the tabletop tree and the diameter of the upper log should be smaller than the lower one. The larger the cut of the segment, the higher the log obtained from the conical top of the plastic bottle. For the top you need a half segment, and for the middle part about two-thirds of the whole neck (Fig. 5b). The diameter of the lower hole of the upper log should be approximately 1 mm larger than the upper hole of the lower log forming the trunk.

It's time to attach the branches to the "logs". Each log will need to place 2-3 tiers of branches. A small number of tiers does not allow you to effectively cover the heads of the rivets with branches, and a large number spoils the aesthetic appearance of the Christmas tree. In each tier of this design you can install from 4 to 10 branches. Fastening is carried out using plastic rivets, since you will need quite a lot of plastic rivets, it is better to prepare them for future use. The easiest way is to place the branches in tiers on the lower logs (Fig. 6), since the neck of the plastic bottle is wide enough and it is convenient to hold the plastic rivet from the inside with your finger.

If you place the branches closely along the circumference of the tier, then one rivet is enough to attach the branch to the trunk (Fig. 6-8). For those who like greater reliability, they can install two rivets side by side. The tiers of branches must be formed like the roof deck of a house - from the bottom up, then the branches of the upper tier will cover the rivets of the lower one and the heads of the rivets will be completely invisible.

In my case, in the lower (Fig. 6) and middle (Fig. 7) log of the trunk there are 2 tiers of branches, and in the upper one - 3 (Fig. 8). There are 5 tiers of branches in total. It’s quite enough to look amazingly similar to a real tree. Installation of plastic rivets on the upper tier, due to its small diameter, should be done using tweezers or a medical clamp.

After securing all tiers to all logs, you can begin final assembly. But first it is advisable to decide on the top. In my case, without thinking for a long time, I built the top using the same technology as the trunk (Fig. 5), that is, by rolling the plastic into a cone. But you can do this in another way, for example, in the form of an asterisk or a ball (I like the cone better). The top of the tree is attached to the upper element of the trunk also using a rivet, installed from the inside and melted from the outside. The upper part of the trunk, together with the top, is itself a miniature tabletop Christmas tree (Fig. 9). You can install it on your monitor and enhance the holiday feeling...

A living Christmas tree grows from the bottom up, in the same order, and we collect logs with tiers of branches by adding “logs” (Fig. 10) to the already existing Christmas tree. It is better to connect the trunk elements together in a place covered by a branch, at three points along the circumference of the trunk. In this case, the trunk becomes rigid and will not break if the Christmas tree accidentally falls to the floor from the table, the Christmas tree is a tabletop one...

And if you insert a dynamic light part (for example, a garland) inside the Christmas tree, then on New Year’s Eve it will amaze those around you with its charm:

Here is such a master class. Of course, it’s a little complicated, but what a beauty it turns out!

Soon the New Year 2018 will be knocking on all doors, and houses will be filled with the smell of tangerines, vanilla and chocolate cookies, and pine. However, somewhere they will not feel the unique aroma emanating from the green beauty: the owners of these homes, having watched the video and photos on the topic “how to make a Christmas tree with your own hands,” will decide to save nature - not to buy cut down trees. Instead, they will make a Christmas tree at home from such improvised materials as ribbons, balls, pine cones, paper, cardboard, cotton pads, and tinsel. Even decorations for this beautiful craft can be homemade - children will make them during labor classes at school and kindergarten. What else and how can you create a unique Christmas tree? Simple master classes with step-by-step explanations will tell you about this.

How to make a Christmas tree with your own hands at home for school or kindergarten

Surely, you will want to help your child make his best New Year's craft. To do this, first find and mark for yourself the most unusual ideas for creating a fluffy Christmas tree. Study carefully the master classes and photographs that tell you how to make a Christmas tree with your own hands at home for school or kindergarten. Bookmark the pages you marked or print out detailed explanations for creating the craft.

Examples of Christmas tree crafts with photos and videos

If you have been nurturing the idea of ​​making a homemade Christmas tree for a long time instead of buying another cut down tree for the New Year, read how you can make your own Christmas tree at home - bring it to school, kindergarten or decorate your home with green beauty. Pay attention to our selection of photos and videos - the materials will tell you what and how to make a craft from.

How to make a Christmas tree out of paper with your own hands for kindergarten - Master class on crafts at home

Children preschool age They are not yet very dexterous in handling scissors and carefully connecting the parts of crafts. As a rule, a teacher or parents help children of this age make something original. Having learned from us all about how you can make a wonderful Christmas tree out of paper with your own hands and take it to kindergarten, having studied crafts master classes on creating a mini Christmas tree at home , Moms and dads will be able to explain to their children what needs to be done in order for the craft to come out neat and beautiful.

Examples of homemade Christmas trees made from paper and cardboard

For creating paper crafts accuracy and patience are required. Find out how to make a Christmas tree out of paper with your own hands for kindergarten - a master class on crafts at home with photographs will tell you all the steps step by step.

Paper Christmas tree toy for the Christmas tree - Master class with explanations in the photo

To create this mini Christmas tree, a New Year's toy, you will need to carefully study the photo explanations of the master class.

1. Fold the green square of paper in half twice and unfold it - you will see the fold lines.

   
   

2. Start folding the shape, focusing on the fold lines.

   
   

3. Follow all the steps shown in the photo sequentially.

   

   

4. Cut off the part of the workpiece located below.

   
   

5. Make symmetrical cuts on both sides of the workpiece - you will get a Christmas tree!

   

How to make a Christmas tree with your own hands at home for a school competition - Master class with instructions

On the eve of the upcoming New Year, schoolchildren often make crafts for the holiday. IN certain time All finished goods are put on display for other students so that they can objectively name the best work. Of course, every child wants his craft to be recognized as the most original and beautiful. To do this, find out how to make a Christmas tree with your own hands at home for a school competition - a master class with instructions will explain everything step by step.

DIY felted wool Christmas tree - Master class with explanations

If you want to learn how to make felted crafts, read how you can make a wool Christmas tree with your own hands at home and send it to school for a competition: a master class with instructions with photos is attached.

1. Having purchased green wool for felting, wind it into a tight cone.

   
   

2. You need to separate the wool from the skein by tearing it off, not cutting it.

   
   

3. Place the cone on a wet sponge and begin felting it. A pen with a needle attached to it can help you.

   
   

4. Constantly rotating the workpiece, moisten the future Christmas tree in warm soapy water and squeeze a little (be careful - otherwise the craft will lose its shape!)

   
   

5. Place the craft on a wet bag and, rotating it, roll it further - this way the Christmas tree will be stable.

   
   

6. Felt the balls for the Christmas tree in the same way.

   
   

   
   

7. Carefully sew the balls onto the Christmas tree.

   

8. If desired, the Christmas tree can be decorated with a garland. Wrap the craft diagonally, securing the “garland” of beads or beads with several stitches.

   
   

9. To decorate the Christmas tree, you can use bells, beads, jewelry, etc.

   
   

How to make a Christmas tree out of cotton pads with your own hands at home: crafts master class

U good master with a rich imagination, there will always be the most unusual, creative crafts, made from unexpected, unusual materials. Such a craftsman can happily teach you how to make a Christmas tree with your own hands at home from cotton pads purchased in a regular supermarket: a crafts master class and photos are attached.

Master class on “Herringbone” crafts made from cotton pads

Find out how to make a Christmas tree out of cotton pads with your own hands at home: a crafts master class will teach you how to make it step by step. The snow-white beauty will decorate any New Year's interior.

So, prepare first:

• Cotton pads;
• Stapler;
• Silicone glue;
• Cardboard;
• Scissors;
• Beads;
• Green paint.

1. Prepare each cotton pad as shown in the photo: fold it in half and secure it with a stapler.

   
   

2. For a Christmas tree 45 cm high, you will need more than three hundred prepared cotton pads.

   
   

3. Glue a cone from a thick sheet of cardboard, cutting off all excess at the bottom. Start gluing the prepared discs to the cone.

   

4. Work your way from the bottom, gradually attaching cotton pads in a circle.

   

5. Cotton Christmas tree on New Year 2018 is ready and waiting for her outfit.

   

6. Glue beads into the center of some rolled disks, and cover part of the “paws” of the spruce with green paint.

   

How to make a Christmas tree out of threads with your own hands at home: master class step by step

As you already understand, crafts can be made from almost any materials and available means. The main thing here is not what the thing is made of, but creativity craftsman. Learn how to make from threads christmas tree with your own hands at home: the master class will help you master this technique step by step, with the help of photos and explanations.

Craft “Christmas tree” from threads - Master class with photos

Read carefully how simple threads You can make an openwork Christmas tree with your own hands - it’s easy to do at home. Detailed master class will explain to you step by step how to work with materials so that in the end you get a light, patterned Christmas tree.

1. Prepare everything first necessary materials(see photo).

   

2. Make a cone out of paper, making cuts at the bottom. Through these cuts you will wrap the tree with threads like a cobweb.

   

3. Having diluted PVA glue in a bowl to the state of liquid kefir, moisten the threads in it and wrap the workpiece with them. Threads can be of different colors.

   

4. After finishing the winding, wait for the craft to dry. Carefully pull out the cone from inside - you will see a dense openwork Christmas tree. If you place a garland inside it, the tree will shine with New Year's lights.

   

5. If you don’t have a garland, decorate the craft as you wish.

   
   

How to make a Christmas tree with your own hands from tinsel: photo and video instructions

It is customary to decorate houses with tinsel, carnival costumes and ready Christmas trees. Is it possible to make something for them? About, How to make a Christmas tree with your own hands from tinsel, photos and video instructions from the master classes posted on this page will tell you. All you have to do is repeat the actions of the craftsmen.

Large green tinsel tree - photo with explanations

If you decide not to buy a cut-down Christmas tree for the New Year 2018, find out how you can make a fluffy Christmas tree with your own hands from tinsel: in the photo and video instructions you will find all the explanations regarding this creative work.

How to make a Christmas tree with your own hands using available materials - Master class with photos

Surely, every housewife stores in her closets and chests of drawers countless ribbons, beads, ropes, pebbles, scraps of material, broken jewelry and a lot of other similar nonsense. It can be a shame to throw it all away, so read how to make a Christmas tree with your own hands using available materials - a master class with a photo of the finished craft will give you the best tips.

Christmas tree made of ribbons for the New Year 2018 - Master class with instructions

If you already know roughly how you can make various beautiful Christmas trees with your own hands using improvised materials, pay attention to this master class with step by step photos on making a green Christmas tree from satin ribbons.

To work you will need:

• Satin ribbons in three shades of green;
• Green cardboard;
• Glue,
• Scissors,
• Simple pencil;
• Thread,
• Burner;
• Glass,
• Metal ruler;
• Compass,
• Silver and red beads.

1. Using a burner and a metal ruler, prepare 10 cm long pieces of satin ribbon. While protecting the table, cover it with glass.

   
   

2. You should have several dozen ten-centimeter pieces of tape different colors.

   
   

3. Make loops from the ribbons, again using a burner and a metal ruler.

   
   

4. You should have three groups of loops different shades green.

   
   

5. Make a cone blank from green cardboard, drawing it as seen in the photo.

   
   

6. Using a compass, make more arcs, smaller in diameter.

   
   

7. Starting from the bottom, glue ribbon loops in rows in a circle.

   
   

8. At the top of the cone, the loops need to be attached as tightly as possible to each other.

   
   

9. Alternate loops of different shades of green.

   
   

10. Start gluing beads to the ribbons.

    
    

11. As a result, you should end up with such a green beauty.

    

What you can use to make a Christmas tree with your own hands: New Year's craft from pine cones

Going for a walk in the forest, collect the cleanest, neatest pine cones and other natural materials- you will need them to prepare for New Year's holidays. What you find will be what you can use to make a Christmas tree with your own hands: a New Year’s craft made from pine cones will surprise your guests with the originality of its appearance.

Topiary tree made from pine cones: master class with photos and instructions

When you find out what else you can use to make a Christmas tree with your own hands, you will definitely want to make this New Year's topiary craft from pine cones.

1. Before work, prepare all the materials and tools shown in the photo.

   

2. Using heavy scissors, cut off the “leaves” from all the cones collected in the forest.

   

3. Buy a ready-made cone or roll it out of thick cardboard. Starting from the bottom, move in a circle, attaching the “petals” of cones to the base of the future spruce.

   

4. The future Christmas tree itself will soon begin to resemble a huge cone.

   

5. Having reached the top of the cone, form a neat crown of the spruce.

   

6. Now start covering the almost finished Christmas tree with glue and sprinkle with glitter.

   

7. If desired, cover the craft with gold paint.

   
   

8. This unusual topiary tree will fit perfectly into your New Year's interior.

   

What to make a Christmas tree from for crafts for the New Year 2018 and how to decorate it

Photo and video examples of Christmas tree crafts for the New Year

What home craftsmen try to make a Christmas tree from for crafts for the New Year 2018, how diligently they decorate it! Newspapers, magazines, packs of souvenir money, plastic bottles and cups, peas, pasta, socks, notebooks, tinsel, etc. are also used. Balloons And much more. The photo shows how creatively the creators of the most creative Christmas trees approached their work.

How to make a Christmas tree with your own hands from plastic bottles - master class with photos and videos

Sometimes we don't even realize how much unique material We have some for crafts at home! If you and your children often buy bottled water, kvass and lemonade, find out how to make a Christmas tree with your own hands from plastic bottles - a master class with photos and videos will help you with this.

Homemade Christmas tree from plastic bottles - Master class with photos

Having learned how to make an unusual light Christmas tree with your own hands from plastic lemonade bottles and having studied this master class with photos and videos, you can easily replace better replacement a tree cut down in the forest. Of course, before you start work, you should prepare everything you need in advance, namely:

• A large number of plastic bottles;
• Frame for spruce (from PVC pipes or wooden slats);
• Wire;
• Three cans of green and one can of silver paint;
• Stationery knife;
• Scissors;
• Drill or thin drill bit;
• Electrical tape;
• Spruce stand.

1. Assemble the frame for the Christmas tree. Attach plastic corners to a piece of PVC pipe. They will serve as the basis for the side legs of the spruce. Make holes on top of the “legs” (they don’t touch the floor!) and in the middle of the pipe by threading wire through them. Secure it with pliers. Secure the cut top of a plastic bottle between the “legs” - this will make the structure stronger. Secure everything with electrical tape.

   

2. Cut off the bottom of the bottles.

   
   

3. Cut the rest of the bottle into “noodles”.

   
   

   
   

4. Manually peel the strips away from the neck.

   
   

5. Fold the strips up, cut off the necks of the bottles and paint the blanks with green and silver paints. You can do without paints by initially using multi-colored bottles.

   
   

6. Start assembling the Christmas tree by stringing the pieces, necks up, onto the base. Screw the lids onto the lower legs. Drill holes in them and, using a wire stretched through the hole, secure the structure.

   
   

   
   

7. Secure the top of the spruce with wire.

   
   

8. Place the tree in the stand. Decorate it with silver paint and tinsel.

   

   

A wonderful one is coming winter holiday— New Year 2020. It’s time to decorate your house for its arrival, so that Santa Claus on his magic sleigh does not pass by and leaves good gifts under our tree. It is very interesting to decorate the Christmas tree and rooms with homemade toys for the holiday. The process of making them is fascinating, as is any creativity. Such crafts can be made from the most simple materials, for example, from plastic bottles. From ordinary plastic bottles you can make a lot of interesting and beautiful things that can successfully replace store-bought analogues. Our story today is dedicated to the 7 best and original crafts from plastic bottles for the New Year 2020, which will be held under the sign of White Metal Rat. Let's look at them in detail in our article.

Christmas tree

An unusual Christmas tree can be made from simple plastic bottles. It is important to collect necessary materials for this craft and follow the master class step by step.

To do this you will need:

• Plastic bottles;
• Scotch;
• Sandpaper (cardboard);
• Scissors.

Progress:

1. The bottom and neck of the bottle should be removed, and then you will get a straight pipe. Then you should prepare blanks from twigs. They must be of different sizes so that the Christmas tree turns out to be cone-shaped.
2. Then the plastic bottles need to be cut lengthwise into 3 parts so that subsequent tiers are smaller than the previous ones. You need to make needles on each workpiece, and to do this they are cut into thin strips, but not completely. To make the Christmas tree stand stable, it is advisable to use the bottom of one of the bottles as a stand.
3. A sheet of cardboard needs to be rolled into a tube and placed in the neck of the bottle. You can secure it with tape. Now each tier of branches needs to be secured to the tree. You can install a toy on the top or come up with something else. To make the Christmas tree fluffy, the needles should be cut thinner. Usually blue or transparent bottles are used for this. That's all, our craft is ready!

Christmas balls

You can decorate your Christmas tree with handmade toys. In your work, it is important to follow all the steps step by step, and then you will get wonderful products.

To do this you will need:

• Plastic bottle;
• Glue;
• Rain;
• Any shiny jewelry.

Progress:

1. The paper needs to be wrapped around the bottle: this will help mark the workpieces on it. It is necessary to cut out 4 rings 1 cm wide. Then the rings must be fastened together using the “crosswise” principle and secured with glue. The result should be a ball of plastic strips. You need to choose beautiful threads or rain so that the toy can be used for the Christmas tree.
2. To decorate the resulting blanks, it is better to use foil, beads, seed beads, etc. You can place inside such a ball small ball. You can use as much imagination as you like with this craft. This will be a very interesting activity for children.

Snowflakes from plastic bottles

To expand the range of crafts made from plastic bottles for the New Year 2020, you can also make snowflakes from the bottoms of bottles as a Christmas tree decoration. This process will also be possible for beginners in this creative endeavor.

To work you will need:

• Scissors;
• Acrylic paints of white, blue, gold, silver - to choose from;
• Plastic bottles, preferably blue;
• Paint brush;
• Wire;
• Pliers.

Progress:

1. We take plastic bottles and stationery knife or use scissors to cut the bottom as low as possible to the base, leaving only the grooved part.
2. After the bottoms are ready, we begin painting our future snowflakes. Depending on the desired design, select the thickness of the brush, and then start painting. As drawings, you can use various ornaments that come to your mind. This also applies to the choice of paint color with which you will decorate your New Year's product.
3. Once your snowflake has turned into a beautifully painted masterpiece, give it time to dry while you use wire and pliers to make a small eyelet for the thread. Attach it to the snowflake and thread the thread into this ring.

Well, ours is ready New Year's toy for a Christmas tree decoration that you can now be proud of. A DIY snowflake can serve worthy decoration not only your home, but also kindergarten if you have Small child, and also act as an exhibit at an exhibition at the school of New Year's products.

Penguins made from plastic bottles

Original New Year's decoration Your home for the New Year 2020 may include penguins made from plastic bottles, which should be placed in the rooms and under the tree as decoration. This craft will delight all your family and guests, and especially children. Without spending a lot of time, you will create with your own hands a real masterpiece of art that will cause a lot of positive emotions and sincere smiles in your household.

To work you will need:

• Plastic bottles (one toy takes two bottles);
• Scissors;
• Acrylic paints - white, black, red and others;
• Brushes;
• Small colored scraps for a scarf;
• Buboes or bows for hats;
• Glue.

Progress:

1. We take the bottle and cut off the top part almost completely or half to get the body of a penguin. The head is made from another bottle and also from the lower part, but the workpiece should be slightly smaller.
2. We connect both blanks by inserting the upper part, which is smaller, into the lower part, which is larger.
3. After you have built the penguin's body, start painting it. Take acrylic paints and apply carefully to plastic product, imitating the color of a penguin, as shown in the photo. Use more bright colors, because the brighter your New Year's penguin turns out, the warmer and more cheerful the smiles of your family will be.
4. When your penguin takes on a realistic look, you can tie a small scarf around its neck and attach a bubo or bow to its cap using glue.

What a cartoonish miracle you have created!

Video tutorial on making penguins from plastic bottles

Golden bells

Golden bells will look original on the New Year tree. This work is done very quickly and is suitable for kindergarten.

To do this you will need:

• Plastic bottles;
• Acrylic paint, if desired instead acrylic paint you can use fabrics, ribbons and accessories.

Progress:

1. For work, you should take 0.5 liter bottles, but more is possible if the tree is very large. The bottom of the bottle should be cut off. To make bell petals, you need to cut the edge of the bottle in a zigzag shape. Because the resulting edges will be sharp, care must be taken.
2. The petals of our craft need to be made pointed, and you can use a knife to give them shape. To make holes for the rope, you need to heat the knitting needle and make holes. You can do this work with scissors, but be very careful. At the end of the work, the bells should be painted, and they will dry within an hour. To give the products a New Year's look, they need to be decorated with tinsel, garlands or sparkles. The instructions are simple, and you can do the work in your own sequence.

Candlesticks made from plastic bottles

To do this you will need:

• Plastic bottles;
• Scissors;
• Glue gun;
• Universal glue.

Progress:

1. You can make a wonderful candlestick for the holiday with your own hands. You can use bottles of different colors. The containers need to be cut in half. The edges of the part that remains with the bottom should be cut into strips, not reaching 4 cm. The strips can be different widths. The resulting container will be a candle stand.
2. Strips of plastic should be melted over a candle. Then use a glue gun to attach the candle to the foil. The space around the candle can be decorated with beads or stones. So the candlestick will have light weight, our craft is ready.

Video master class on making candlesticks

Cone

You can make original cones with your own hands; this craft from a plastic bottle will perfectly decorate your Christmas tree and home for the New Year 2020.

To do this you will need:

• Plastic bottles;
• Scissors;

Progress:

1. You need to create squares from a plastic bottle, after which their corners should be rounded. The result will be products like chamomile. After this, you need to treat the edges of the petals with a candle so that they fall down.
2. All parts must be strung on a thread in descending order. A bead must be inserted between them. Then you need to make a spruce branch and secure it to the pine cone. The product is ready to create a festive atmosphere.