White silicone for the bathroom. Sealants for the bathroom - choosing the best, correct application technique. How to choose the optimal sealant

When renovating a bathroom, special attention should be paid to sealing the joint between the plumbing and the wall. It is into the gap along the perimeter of the font that splashes fall. The area under the bathroom is practically not ventilated, so puddles do not dry out well and high humidity and mold. High-quality sealing gaps avoids these problems and extends the service life of the facing material.

What problems does bathroom sealing solve?

Installing a bathroom close to the wall is impossible for a number of reasons: curvature of the floor or the walls themselves, inconsistency of plumbing fixtures with the dimensions of the bathroom. As a result, cracks appear through which water will leak during bathing. Lack of tightness of joints can lead to negative consequences:

1. During active bathing or showering, splashes fall through the cracks onto the floor. If the formed puddles are not wiped dry in a timely manner, water will begin to seep into the lower floors and will flood the neighbors.
2. Regular “flooding” of the bathroom significantly increases air humidity, which provokes the appearance of mold on the walls, ceiling and floor, as well as the development of pathogens.
3. High humidity negatively affects the decoration of the room - the seams between the tiles lose their aesthetics and darken. Even high-quality repairs will not withstand the fatal effects of moisture and will become unusable within two to three years.

High-quality sealing of seams between bathtubs, shower stalls, sinks and walls - important stage repairs that cannot be neglected. Even an amateur construction worker can handle the job.

Methods for sealing the joint between the wall and the bathtub

Before sealing a bathroom, you need to assess the condition, size of the gap, and the material of the adjacent surfaces. An important factor when choosing a method is the price of the issue. The main thing is that the selected material meets the requirements of water and heat resistance.

Let us examine in detail how to seal the joint between the bathtub and the wall using the most common and effective methods.

Cementing the gap is an outdated method of processing joints

The “old-fashioned way” of sealing is to use cement mixture. With the advent of modern building materials, its popularity has decreased, but this has not made the method any less effective.

To work you need to prepare:

• container for mixing the solution;
• sand;
• cement grade 400 or 500;
• plasticizer (clay or lime);
• water;
• plaster spatula;
• foam sponge or pieces of rags.

Procedure for mixing the solution:

1. Combine sand with plasticizer in a ratio of 4:0.8 if lime is used, 4:0.5 if clay is used.
2. Add cement to the dry mixture of sand and plasticizer. Proportions of the constituent components: 4:0.5 (sand/cement M400), 5:1 (sand/cement M500).
3. Stir the mixture until smooth.
4. Gradually, adding water in small doses, knead the solution to the desired consistency.

Sealing technology:

1. Clean the sides of the bathtub, removing all construction debris, dirt or remnants of previous grout.
2. Place a container under the gap to cement mortar didn't flood the floor.
3. Cut the fabric into long pieces, soak them in the mixture and fill the cracks with them.
4. Using a spatula, apply the solution around the perimeter of the connection between the plumbing fixtures and the wall.
5. Remove excess cement mixture with a damp sponge.

After the solution has set, the coating can be sanded a little and painted with oil paint.

Using polyurethane foam: pros and cons

Experienced builders find the use of polyurethane foam when performing various repair tasks. Universal construction material It is also used as a sealant for the bathroom. Arguments in favor of this decision:

• availability of material;
• ease of application;
• sufficient efficiency.

Disadvantages of using polyurethane foam:

• a special gun is required for operation;
• the method is suitable for sealing cracks with a width of 3 cm;
• the difficulty of removing polyurethane foam from finished surfaces - tiles and bathrooms.

Important! To work in a damp room, you need to choose a moisture-resistant material. The best option- one-component polyurethane foam.

Sealing the bathtub seam is performed in the following sequence:

1. Clean adjacent joints and degrease the surface with alcohol or solvent.
2. Wipe dry and seal the sides of the bathtub and the wall with masking tape - this will prevent foam from getting on them.
3. Pre-hold the cylinder in a warm room - this will increase the elasticity of the sealant.
4. Shake the bottle of foam.
5. Insert the can into the gun and turn it upside down.
6. Put on gloves and carefully squeeze out the foam while moving along the joint.
7. After drying, cut off excess foam sealant.

Installation of plastic or ceramic skirting boards

Sealing the bathtub with a corner is a simple and “clean” method. The sealed joint looks neat, and the border copes with the task quite well. There are two types of corners:

Installation procedure for plastic self-adhesive plinth:

1. Cut the border to the desired size.
2. Clean the joining surfaces.
3. Heat the back side of the border a little to activate the adhesive, apply and press the corner tightly.
4. Fill all visible seams with transparent silicone sealant.
5. Install plastic plugs at the ends of the baseboard.

The technology for installing ceramic borders is similar to the process of laying tiles. The baseboard is attached with tile adhesive, and the seams are sealed with moisture-resistant grout.

Curb tape sealing technology

Bathroom Sealing Tape Available different widths and in various color solutions. When choosing a strip border, you must take into account that its width should be at least 10 mm greater than the width of the slot. It’s better not to save money and install a larger strip.

The seal is glued using the following technology:

1. Surface preparation: cleaning, degreasing and drying.
2. Cutting the tape into three strips with an overlap on side elements 1.5 cm each.
3. Bending the border along the length along the notches.
4. Press the self-adhesive tape onto the joint.

Tips for working with strip borders:

• synthetic material needs to be replaced every 2-3 years;
• After applying the tape, it is not advisable to use the bathroom for one day;
• It is better to give preference to products with antifungal impregnation.

Finishing the joint with tiles

A popular and aesthetically pleasing option is to close the joint gap tiles, selected in the same style with the entire bathroom decoration. Remains of laying tiles can be used, decorative border from a single series with tiles or ceramics “in contrast”.

The method is universal, as it is suitable for sealing cracks of different widths.

Bathroom tile sealing technique:

1. If the gap width is 1-3 cm, then it must first be filled with foam.
2. While the foam hardens, you can cut the tiles into pieces of the desired thickness.
3. Apply tile adhesive to the foam and border tiles, and attach the tiles to the base.
4. As you lay, crosses must be placed between the elements to ensure evenness. between tile joints.
5. After the glue has hardened, fill the holes between the tiles with grout.

If between the wall and the bath long distance(more than 5 cm), then it is necessary to equip a structure made of moisture-resistant plasterboard or a kind of formwork. The gypsum plasterboard frame must be puttied and lined with cast iron, and the formwork must be poured cement-sand mortar and lay tiles on top. The result should be a practical shelf that fits snugly into the bathroom.

Filling the gap with decorative grout

The method is less in demand than the above methods, as it allows high-quality sealing of joints up to 5 mm wide. In this case, the distance from the bathtub to the wall along the entire perimeter of the junction should remain almost the same - let’s say a difference of 1 mm per linear meter. If this condition is neglected, the resulting seam will look uneven. In situations where the gap is more than 5 mm, the technology is ineffective.

An additional limitation to the use of a fugue for sealing a gap is the material used to make the bathtub. The method is only permissible for cast iron plumbing fixtures, since models made of acrylic and steel tend to change their dimensions during operation - under the influence of high temperatures, the materials increase in volume or settle under high loads. As a result, the grout begins to crack and the joint becomes depressurized.

The benefits of using grout include:

• decorativeness of the method - the designed joint completely repeats the seams between the tiles, creating a unified perception of the bathroom interior;
• accessibility - the remains of the grout joint after processing the seam between the tiles are used for implementation;
• simplicity and speed of application.

The process of processing a joint consists of preparing the seam (cleaning/degreasing), preparing a tinting composition and rubbing the mixture into the gap. After a day, the fugue is cleaned with sandpaper.

Use of sealants: silicone and acrylic compounds

Moisture-resistant sealants are used to seal cracks up to 15 mm wide. Silicone, acrylic or combination compounds are optimal for the job. Silicone sealants are most often used in bathrooms, but two other options are also acceptable.

Nuances of choice:

1. Silicone sealant comes in two types: neutral and acidic. The most suitable is the sanitary neutral subspecies. It contains antifungal additives. The disadvantage of neutral sealant is its high cost. Acidic ones have a pungent odor and can corrode metal surfaces.
2. When choosing an acrylic composition, you need to pay attention to its water resistance. A waterproof plastic sealant will do the job.
3. The packaging must indicate the recommended scope of application, operating temperature and shelf life.
4. It is better to buy sealant in a store; it is advisable to choose products from popular brands: “Moment”, “Titan”, “Wepost”, “Delta”.

To apply the sealant you need to prepare: a special gun, rubber spatula, degreaser and sponge.

The procedure for sealing bathroom seams with sealant:

1. Clean and degrease the surfaces to be treated.
2. Leave the bath to dry for half an hour.
3. Prepare the sealant: cut the tip of the bottle at an angle of 45°, put a protective cap on it and place the bottle in the mounting gun.
4. Distribute the sealant evenly.
5. Remove excess material with a moistened spatula.

1. Before use, the font must be filled with water and left for 1-2 hours. The plumbing will shrink, which will reduce cracking of the sealant layer in the future.
2. When using cement mortar, do not allow it to get into drainer. The bottom of the bathtub must first be covered with polyethylene.
3. In practice, a combined method of sealing joints is often used. For example, cement mortar or polyurethane foam The top is closed with a decorative border.

To minimize the gaps during repairs, it is necessary to level the walls and floor. Errors in the slope of the wall lead to inconsistencies in plumbing and structural elements premises.

Moisture protection for wooden floors

The desire to decorate the house natural materials - current trend in the construction industry. Particularly daring people use wood even when decorating floors in “wet” rooms. Having decided to take such a step, it is necessary to ensure sufficient waterproofing of the coating.

Sealing a wooden bathroom floor is carried out with various protective materials:

1. Oil. Modern coating materials are developed based on natural oils and contain synthetic additives: polyurethane or hard wax. The oil penetrates deeply into the wood structure, filling microcracks in the material. The composition prevents swelling or drying out of the wood.
2. Wax. Recommended for use over oil. Waxed floors are moisture resistant, but to maintain the achieved effect, the procedure must be repeated every 1.5-2 years.

Sealing joints between wooden joists performed with a special sealant for wood. The material allows the wood to breathe, and due to the elasticity of the composition, expansion and contraction of the coating is compensated.

Mold in the bathroom

No high-quality bathroom renovation can do without modern sealant.

Bathroom anti-mold sealant is a viscous substance that contains a material that can block the path of water into seams and joints, thereby preventing the accumulation of dampness.

Sealing a bathtub with a wall

Before choosing an anti-mold sealant for your bathroom, you need to understand the types and purpose.

For use in the bathroom, sealants based on:

• silicone;
• acrylic;

Acrylic Bathroom Sealant

• acrylic silicone;
• polyurethane.

Silicone based sealants

Silicone sealant is designed for bathroom tiles.

Silicone Bathroom Sealant

It is used to seal the seams between tiles, since silicone is an excellent water-repellent material. The good components of this material do not lose their properties during sudden temperature changes. Silicone sealant is divided into 2 types:

• acid;
• neutral.

Unlike the neutral type, the acidic (acetic) type has a pronounced pungent odor. Acidic is suitable for use on surfaces that are not susceptible to oxidation.

As for the neutral sealant, it does not have an acidic odor and comes into contact with any metals quite easily. IN acrylic bathtubs This type is usually used.

Unlike silicone, acrylic sealant does not have a piercing odor. This sealant contains components that prevent the development of pathogenic microorganisms.

It should be remembered that acrylic sealant does not have a piercing odor.

But the material does not have plastic properties and is capable of cracking when it hardens. These properties do not allow it to be used in places where the surface may be subject to any impact. Quite often it is used when carrying out floor works, since it hardens quickly and has good strength properties.

Sealants based on acrylic silicone

Acrylic silicone sealant protects quite well from moisture, is resistant to temperature changes, and remains elastic during hardening. It is white in color, which allows it to be used when processing tile joints, as well as the junction of the bathtub with the wall.

Acrylic inclusions, which are source material sealant, glues quite well, so it is used as an adhesive-sealant.

Polyurethane based sealants

This sealant is similar in its qualities to the silicone composition, but it can be used for various decorative elements, it has good adhesion to any building materials.

Polyurethane based sealant for bathroom

Due to its transparent color, it is used for sealing tile joints.

The right way to choose a sealant

A specialized store will help you choose a high-quality sealant for treating seams and joints between the bathtub and the adjacent surface. Focus on the recommendations that a specialist in this field will give you. Do not try to choose the composition yourself.

Please note that:

• the sealant must be waterproof;

Application of waterproof sealant

• the sealant must include antifungal substances and antiseptic inclusions that will effectively prevent the occurrence of mold and mildew;
• The color scheme of the sealant also needs to be taken into account.

The brand of sealant also matters, because in addition to materials intended for household use, there are also professional compositions.

Bathroom sealant colors

To seal plastic plumbing, you need to take compounds that include substances for working with acrylic and PVC.

What security measures are in place?

When using these chemicals, you need to take safety measures in the form of: rubber gloves so that the substance does not get on your hands, a respirator and good ventilation in the bathroom.

Rubber gloves for working with sealant

To protect tiles and other surfaces from substances getting on them, you need to use masking tape.

What preparatory work needs to be done

Usually, joints are sealed after the bathroom renovation is done. Then the surface needs to be cleaned and degreased. However, it is more difficult to seal a second time, since it is more difficult to remove the sealant from the surface than to apply it.

Rubber spatula for removing sealant from the surface

Here are a few methods to properly remove sealant from a surface:

• if the product is applied immediately after the repair has been made, then there will be no special problems with its removal: a rubber spatula copes with this task perfectly;
• if the composition has frozen, you will have to use gentle movements using stationery knife remove the top layer of material from the coating;
• It is even more difficult to clean or correct old seams that were applied quite a long time ago. However, a variety of chemical removers are used in aerosol packaging or paste-like formulations;

Removing silicone sealant with a blade

• chemicals are applied to the residual seams and removed through certain time along with a sealant napkin. The procedure requires repeating if the desired effect is not achieved. Do not apply immediately chemical agent to the surface - you need to check it before starting work on a small area. Some substances can damage finishing materials.

How to apply sealant

First you need to follow the steps below:

• Apply the product to a previously cleaned and dry surface. A seam that is too deep is dried with a hairdryer. An additionally treated surface will provide good adhesion to the sealant;

Correct application of sealant

• Sealants should be preferred based on the type of cracks that need to be sealed. Wide cracks are sealed with acrylic, and narrow cracks with silicone. It is worth paying attention to the size of the tubes. If you are doing small jobs, it is better to purchase several small containers - working with them will be much faster and more convenient. To properly install the tube on the gun, you need to cut the end of the package at an angle of 45 degrees. Next we attach the cap, which is included in the kit along with the drug. Only after these steps can you install the tube into the mounting gun;
• We also remove the masking tape from the surface, preferably before the sealant has time to harden. Otherwise, the existing layer may be damaged. There are cases when the composition gets on the bathroom wall or tiles. You can remove it by rubbing it with a rag soaked in solvent or gasoline. To do this, wet a cloth and gently wipe away the dirt.

Silicone and acrylic sealants dry in about a day, polyurethane - from 8 to 10 hours.

The bathroom is a type of room where moisture is constantly present in large quantities, as well as steam and large changes in temperature conditions. It is for this reason that when renovating a bathroom, special moisture-resistant materials are selected for the job, which includes bathroom sealant. In this article, we will look at what types of sealants there are and which ones are best used for waterproofing joints indoors, based on reviews and recommendations from experts.

Modern sealants for the bathroom are very popular and many renovations cannot be done without this material. They are used mainly for sealing joints between the bathtub and adjacent wall surfaces, as well as for stickers decorative corners.

It is known that a large accumulation of dampness in some places in the bathroom not only leads to destruction finishing material, but also creates a favorable environment for the growth of mold, which saturates the air with its pores and can cause disease. This is why bathtub sealant is used against mold, which blocks the access of moisture to areas such as the space under the bathtub. In this place, ventilation is very poor or non-existent, and this creates an ideal environment for the development of bacteria in the presence of moisture.

What is silicone sealant

Before choosing a sealant, you need to find out what types there are and in what places they are used. Today, a sealant is a liquid viscous substance that basically contains polymer material as a binder for various modifying components included in its composition. Depending on the polymer base, sealants can be:

• silicone;
• bitumen;
• acrylic;
• rubber or rubber;
• polyurethane;
• thiokol.

For your information. Not all of the listed materials are used in the bathroom. The most commonly used are polyurethane, acrylic or silicone sealant for bathrooms.

The physical characteristics of sealants are given by the composition of their main filler, and various additional components only enhance certain qualities of the substance. Some of the listed types are not recommended for use in the bathroom as waterproofing of seams; therefore, below we will only consider sealant for seams in the bathroom and other work in the bathroom.

Main types of bathroom sealants

• silicone;
• acrylic;
• acrylic-silicone;
• polyurethane.

Each of these materials has its own characteristics and is suitable for different cases, so it’s up to you to decide which sealant to choose based on your circumstances.

Silicone sealant

Silicone is a sealant for bathroom tiles, which is mainly used for sealing joints between tiles and has excellent water-repellent characteristics. This material can withstand sudden temperature changes and does not lose its physical properties. This type is also called sanitary sealant, since it is inert to the effects of most chemicals. It can be used in rooms with a constant temperature of -50 to 180 degrees Celsius.

Important. Sanitary sealant for the bathroom can be of two types, acidic and neutral.

The acidic composition has a characteristic pungent odor, similar to the smell of vinegar, and is much cheaper than the neutral one. However, this composition, when interacting with metals, causes oxidation, so they can be used on a metal surface with protective coating or stainless steel. Neutral silicone-based bathroom sealant costs a little more than its counterpart, but it does not have the same reaction with metals as an acidic one and does not have a pungent odor. This composition is often used as a sealant for acrylic bathtubs.

Acrylic sealant

This composition does not have any strong odors, sometimes even odorless. Its cost is lower than its silicone counterparts, but this acrylic bathroom sealant cannot be used in places that may be subject to minor mechanical stress or deformation during operation. This is due to the fact that when hardened, this material has no elasticity and begins to crack when deformed.

For your information. The acrylic composition is also called antifungal sealant, since it contains components that prevent the emergence and development of pathogenic microflora. However, due to its properties of fast hardening and providing a strong joint, it is often used as a floor sealant.

Acrylic-silicone sealants

This waterproof bathroom sealant combines the best qualities of the two materials described above, since it simultaneously provides protection from moisture, withstands large temperature changes and, when cured, retains elasticity, which allows it to withstand tightness under small deformation loads. In color, it is most often a white sealant and can be used both for sealing tile joints and for sealing the joint between the bathtub and the wall.

For your information. The acrylic composition has good adhesive qualities and is often used as an adhesive sealant for the bathroom. Manufacturers also produce this type of material in various colors, which allow you to choose desired color for sealing tile joints.

Polyurethane sealants

Polyurethane bathroom sealant is similar in physical properties to silicone, but it has high adhesive qualities and can be used for gluing decorative corners. This transparent sealant and it is very often used as a repair material for tile joints, as well as butt joints, which were previously filled with silicone sealants.

How to choose the right sealant

If you want to choose the best sealant for sealing tile seams or the joint between the bathtub and adjacent surfaces, then when you go to the store and choose the required material Consider the following recommendations from experts:

• the composition must first of all have moisture-resistant characteristics, since there are compositions of sealants without water-resistant properties and they differ only in the corresponding recording on the tube;
• try to buy products that contain antibacterial additives. Of course, such a sealant will cost a little more, but it’s worth it;
• Pay attention to how much the sealant costs. A good sealant cannot be cheap, and if you see the material you need at a significantly reduced price, then you are looking at either an outright fake or the composition has expired;
• try to buy brands from trusted manufacturers. Today the most trusted ones are: domestic producers like “Titan sanitary” or “Moment”. For styling plastic corners choose a material labeled “For PVC and acrylic products.”

Having studied the material proposed in the article, you already know which sealant to use for your needs. And to consolidate the material, we suggest you watch the video material attached below.

Sanitary sealant for bathroom – excellent remedy for sealing joints in conditions of high humidity. It contains many components, including silicone, adhesion enhancers, plasticizers and other additives that ensure high-quality adhesion of the composition to the surface being treated.

Silicone sealants - for a long time

To find out which sealant is best for the bathroom, you need to understand what kind of products are presented on the market. modern market. The compositions differ in characteristics and performance, which depend on what the sealant is made of.

One of the most popular types of polymers is silicone bathroom sealant. Its positive qualities include:

• effective adhesion to various surfaces;
• resistance to environmental influences high humidity;
• resistance to temperature changes and ultraviolet radiation;
• low shrinkage at 2%;
• elasticity, thanks to which it can be used to seal joints of moving surfaces;
• durability;
• wide range of colors;
• Possibility of use indoors and outdoors

There are two main types of silicone grout sealers - neutral and acidic. Neutral sealant is quite different high cost, however, it can be used in any conditions and treat any type of surface. The acidic product has a specific “acetic” odor; it can oxidize surfaces, and therefore cannot be used for processing metals. Acidic materials can be used to seal plastic, glass, ceramic and wooden products not subject to oxidation.

One of the best sealants for bathrooms with silicone in the composition is sanitary. It contains special fungicides that effectively kill fungus and mold. That is why it is believed that it is ideal for treating joints that are constantly in contact with water during operation.

There are also aquarium materials - acidic silicone compounds that do not contain additional components and are therefore suitable only for working with glass products, they are used for sealing showers, for sealing aquariums, etc.

Acrylic sealants – harden quickly

The second common type of sealants are acrylic-based compounds. They do not last as long as silicone ones, but they also have important advantages:

• resistance to temperature changes;
• UV resistance;
• high adhesion to different surfaces;
• Possibility of coating with paint or varnish;
• hardening occurs within 24 hours.

Since acrylic products are not characterized by the elasticity of silicone, they cannot be used to seal joints of moving surfaces, since such a seal is highly likely to deform during operation. These materials are best suited for filling the space between brick, stone and concrete surfaces, as well as for grouting wide joints.

Not all acrylic preparations are resistant to moisture, so before purchasing the composition you must read the instructions from the manufacturer.

Silicone-acrylic compounds include both of these components and combine them positive traits.

Polyurethane sealants - pros and cons

The third type of sealants is polyurethane compounds. They are well suited for sealing joints between wood, stone, glass and concrete surfaces. The positive characteristics of polyurethane preparations include:

• rapid hardening;
• Can be used as an adhesive;
• availability of transparent, colored and white options on the market;
• elasticity;
• resistance to external influences;
• Possibility of painting.

The main disadvantage of polyurethane materials is their aggressive effect on human skin upon contact. When working with such compounds, be sure to use personal protective equipment - gloves and a mask.

Almost all formulations on the market include a large number of additional components, which include fillers, extenders, solvents, dyes, mineral oils and others. They add sealants positive characteristics, however, their quantity should be very limited (no more than 10% of the total volume of material), otherwise they may adversely affect the adhesive and insulating qualities of the goods.

How to choose the appropriate composition for sealing joints in the bathroom and toilet?

The correct choice of sealant determines the quality of seam sealing; fortunately, the rules for choosing such materials are quite simple. To guarantee a successful repair, it is enough to consider the following characteristics of the sealant:

1. 1. Color. Materials available on the market white, transparent and various bright shades.
2. 2. Moisture resistance. In conditions of high humidity, it is necessary to work with compounds that can withstand the adverse effects of moisture. This information must be indicated on the packaging of the product.
3. 3. Purpose. There are household and professional sealants. Professionals are the best technical characteristics, but working with them is much more difficult.
4. 4. Surface type. Some surfaces may require the use of special sealing solutions, for example, when working with PVC panels.
5. 5. Volume of impurities. There shouldn't be too many additional components.

Having analyzed the market for modern sealing compounds, professionals have identified several that are most suitable for use in bathrooms and toilets. The first one is Ceresit CS 25– universal silicone grout-sealant. One of the most popular products on the market, which can be used for both sealing and grouting. It contains antifungal additives, which minimizes the likelihood of mold appearing in the room.

Ceresit CS 25 has good adhesion to glass, enameled surfaces and ceramics, it is characterized by high elasticity and fits perfectly on any surface, including smooth and porous. The composition is classified as an acidic material, so it should not be used on metals.

If needed good material for ceramics, you should definitely opt for Belinka Belsil Sanitary Acetate. This silicone sealant is formulated with strong anti-mold additives and has a paste-like consistency that makes it easy to work with. The product is characterized by increased viscosity and therefore will not wash out upon direct contact with water, which makes it ideal for grouting ceramic tiles.

When required high-quality composition for wide seams, pay attention to Moment Germent. This is the name of a whole series of sealing products that are well suited for sealing problem joints. These sealants allow you to effectively seal even the largest seams and you need to choose between them taking into account the operating conditions of the room. In rooms with high humidity it is better to use silicone sanitary Moment or silicone universal; acrylic compounds are suitable for other rooms.

Best Bathroom Sealant Against Mold – S 400. It contains antifungal additives that are much more effective than those from other manufacturers. The presence of powerful fungicides almost completely eliminates the likelihood of fungus and mold appearing even in the most problematic rooms. In addition, S 400 has excellent adhesion to smooth and non-porous surfaces, moisture resistance and durability. Available in stores in different colors.

Among the compositions with the most better adhesion Available sealant can be applied to various surfaces CIKI FIX. Silicone composition from a Turkish manufacturer, it reliably adheres to other materials, almost tightly fixing wood, metals, ceramics and enamel coatings. It is also moisture resistant and will not wash out with water. However, it does not have antifungal components, so if there is a possibility of mold appearing in the room, it is better to choose another material.

The modern market offers everyone a huge selection of products for sealing and sealing seams. You need to choose among them taking into account future operating conditions and your own individual needs.