A pond at the dacha using hands from a bathtub. Pond from an old bathtub

13.06.2019

Everything you need for the exam in social studies

Comparative characteristics of -C3 and -C4 plants

Since it’s easy to make a pond from a bathtub with your own hands, if you wish, you can carry out all the steps yourself, thereby achieving good result. A small well-groomed pond from a bathtub will become a real decoration for any personal plot. You can arrange such a decorative pond yourself using available materials. Using various waste plumbing elements, you can even create a multi-level artificial pond from a bathtub with your own hands, suitable for populating ornamental carp or turtles and frogs. It’s enough to just figure out how to do everything yourself with minimal costs. So how do you make a pond out of a bathtub?

Preparation for arrangement

In order for an artificial pond to become a real decoration of a summer cottage or personal plot, it is necessary to take into account the mass important points. First of all, you should choose the right place for the pond. It is best if the pond from the bathtub in the country, made with your own hands, will not be under direct sun rays. In the bathroom, the volume of water is quite small, so it will heat up quickly, which contributes to algae blooms, a decrease in the level of oxygen saturation in the water and the death of plants and those inhabiting the pond from old bath animals. You should also not choose an area that is too dark, as this can also contribute to the death of existing living creatures. In addition, the location of the artificial reservoir under the trees will cause it rapid pollution leaves and other debris.

Among other things, drafts will negatively affect the condition of plants and animals living near the pond. Thus, ideal place for the location of the pond there will be an area near the gazebo, and on the eastern side, where bright lighting will be present only in the first half of the day, while in the second half the water will be darkened by the building. If at some distance from the artificial reservoir there are trees that can cover the pond at the dacha at certain times, this will not be bad.

To set up an artificial pond, one old bathtub may not be enough. If a multi-level design is planned irregular shape, you will need a special film. It is also necessary to prepare the tools that will be needed to install all the elements of the future artificial reservoir. TO the necessary minimum materials and tools include:

cement;
sand;
crushed stone;
clay;
garden wheelbarrow;
Master OK;
shovel;
mesh for forming;
big old saucepan;
special waterproof glue;
bucket;
concrete mixer;
building level.

If you plan to make a regular pond without additional bends and uneven edges, the task is greatly simplified. In this case, it is necessary to prepare the place, and in addition, carry out the initial decoration of the bath before installing it. First of all, you need to turn the bathtub over and trace its contours. In addition, it is required to draw an additional contour at a distance of at least 20 cm. Next, you need to dig a hole, the height of which will be 25 cm higher than the bath itself. At the bottom, another hole should be dug from the bottom drain side, the depth of which should be about 40 cm.

IN additional pit You should install a perforated pan filled with gravel or crushed stone. All excavated soil can be removed garden wheelbarrow, since it will not be needed to arrange the pond. Approximately 5 cm of gravel or crushed stone and the same layer of sand are placed at the bottom of the pit. The process of initially decorating a bathtub involves caulking cement mortar top drain and treatment of container walls special glue, mixed with coarse sand. Next, 4 bricks are installed at the bottom of the pit. The prepared bath is installed on them so that the bottom drain is located above the drainage funnel. It is very important to check the evenness of the sides using building level. Sand should be carefully compacted into the holes on the sides.

On top of the sand cushion should be placed metal mesh. Its edges on one side should extend onto the wall of the bathtub, and on the other have different shapes. If desired, you can form any irregular shapes. Next, a cement pad should be poured onto the mesh. It is necessary to place large stones, small pebbles and other elements into the not yet dried cent, which will later form a decorative base.

Pond from an old bathtub (video)

Installation and decoration

You can start decorating the pond in about 3-5 days, when the cement has completely hardened. In the process of designing an artificial reservoir, you can show your imagination and add decorative elements. The bottom drain must be plugged. Further along the perimeter of the artificial reservoir, that is, at the boundaries of the poured concrete, perennials with spreading leaves should be planted in a figure. Can be planted climbing plants, the branches of which can be successfully placed at the very edge of the water. Around the plants you need to place rounded decorative stones to create a natural effect.

Aquatic plants can be planted at one of the edges of the artificial pond. To do this, fill plastic pots clay mixed with river sand. Plants that do not get wet in water are planted into the resulting substrate. This will allow them to take root. These pots, as well as small river pebbles and large stones, will be located at the bottom of the improvised reservoir in the future.

Now you know how to make a miracle out of a bathtub.

Pond from a bathtub in the country (video)

You can plant the most beautiful things in a pond from an old bathtub. various types seaweed In addition, stone crusts can be placed along the banks of an artificial reservoir. Jug shards come in handy. 2-3 weeks after artificial pond from the old bathtub will be installed, a decision can be made regarding the advisability of placing frogs and other inhabitants there. These are all the tips on how to make a pond from a bathtub in your country house with your own hands.

An effective and desirable structure on summer cottage For many owners it is a personal pond. Don't let difficulties or costs stop you. Today we’ll talk about how easy it is to make a pond from an old bathtub with your own hands.

Choosing a location and preparation details

The initial stage of work includes choosing a location future design, creating a project, as well as purchasing the necessary materials and tools.

In this type of work, a drawing is not at all necessary; the structure can be built, as they say, by eye. But if you are planning a more massive structure with several levels or want to implement the original design move, then it’s better to at least draw up in advance minimal project. This will help you better understand what exactly you want to see on your site, as well as avoid errors during construction work.

For a pond, it is recommended to find a flat, drained, dry surface without defects. It is advisable to place the pond in the shade. If it will be located in the sun, it is better to plant several green spaces nearby to shade the structure. If you are studying the art of Feng Shui, it is recommended to place the pond in the east or south of the site.

You can make a similar pond yourself

Before construction you need to take the following materials:

old bath;
crushed stone;
pebbles;
brick;
natural or artificial stone;
clay;
cement;
glue;
dye or color film.

Don't forget about the material we need

You should also have the following tools in your arsenal:

hammer;
container for solution;
shovel;
sheet of tin or pan;
metal mesh;
level;
gloves.

Video “How to make a pond at your summer cottage”

The video shows the sequence of work on making a pond:

Sequence of work

To build a pond yourself from an old bathtub, you must follow a series of sequential steps:

The bath needs to be prepared. To do this, cement the drain and wait until the solution dries.
We give the surface of the bathtub the appearance of a natural bottom: cover inner part colored film, treat with adhesive or paint in soft colors. Beige, black, gray will do. You can also take soft blue or green - they will give the water a special shade. To prepare the adhesive composition, mix the glue for ceramic tiles with water and dye in the proportions specified in the instructions, to a dough-like mass that will quickly harden. When doing this work, you must wear gloves.
After treatment, let the bath dry for several days, before covering it with a film protecting it from precipitation.
While drying, you can start digging a hole. Place the container on the intended area and mark the boundaries - drive stakes around it and tie it. After marking, start digging a hole the size of the bathtub. In this case, fix the sides of the bathtub 20–25 cm below the ground level when immersed in the hole.
Dig another hole in the main hole to secure the drainage.
We do drainage. Roll up a sheet of tin or take a pan with a hole in the bottom and place it in the recess. Then fill it with crushed stone so that the layer protrudes 15–20 cm above the level of the bottom of the main recess.
Cover the bottom with crushed stone and make a sand cushion. In total, the laid out covering should be 15–20 cm.
Compact the raw materials and remove the container placed in a small recess, working carefully and without haste.
Secure bricks at the corners of the pit.
Grasp the container into the hole. It is recommended that you take the winch and work with a partner to avoid injury and damage to materials.
When submerged, the bathtub drain must coincide with the location of the drainage.
Using a level, check that the upper edges of the future pond are installed correctly and are symmetrical.
Pour sand along the edges of the top side, moisten it with water and compact it firmly.
Place the net along the edges of the future pond in a continuous layer or in four parts. Apply cement mortar and place small stones to stiffen it. After completion, wait for the solution to dry.
Cover the bottom with clay, dilute with water and coat the surface tightly with a layer of 5–7 cm. So root system plants will take root well.
Dig a trench around the pond, lay a net in it and lubricate it with the solution so that there remains a small ditch of 30–40 cm for green spaces.
For decoration purposes, place stones, pebbles or other material around the pond so that the edges of the bath are covered and secure with mortar.
Start pouring water. It is better to do this with a garden hose - the flow should flow in a thin stream. At the same time, watch the soil - it should not erode. It is allowed not to change the water completely, only to add it periodically, and the water overflowing the banks will simply be absorbed into the ground. Draining and cleaning of the reservoir will be required only if there is uncontrolled reproduction of organisms or the development of viruses.
After this, you can begin the landscaping stage.

landscaping

To green a pond, it is necessary to plant perennials, marsh plantings, and plants that love moisture in a prepared earthen ditch. It is also recommended to place several large stones to form the relief of the banks.

Having selected groups of plants, plant them in a pond. To do this, you can place the roots in clay, in flowerpots at the bottom of the container, or on horizontal shelves among small stones.

Other decorations

Decorative additions will highlight the pond favorably and give it greater aesthetics. To decorate the pond and make it more natural, you can place small or dwarf water lilies, lilies, or even add duckweed on the surface of the water.

Plus, you can easily create a natural asymmetry of the reservoir by changing the width and height of the banks. This is done in several ways:

formation of a mini-beach from crushed stone on one side of the pond;
placement of an alpine mound or mixborder.

In addition, you can install a small fountain made of a clay jug, place some figurine figurines, or create a hard floor around the pond so that children can sit or play comfortably. Later, introduce small fish into the water. Verkhovkas are well suited for an improvised pond.

It is not recommended to introduce snails and crucian carp into a pond, since the former reproduce in excessive quantities and completely clean the bottom, while the latter will make the water cloudy due to the fact that they prefer to stir in the ground.

Features of the construction of a multi-level pond

The construction of a pond with several levels requires the presence of several water containers; one bath will not be enough. You can make a cascade-shaped pond, for which you will need to place one bath a level higher than the other and run a gutter between them. This gutter can be of a simple shape, for example, a straight stream or waterfall, or it can be winding, but such a design will be more difficult to implement.

When building a multi-level pond, you will need all the same materials as with a conventional structure, but their quantities will differ. As we have already said, you will need another container and material for the gutter; you can take a plastic pipe.

The old bathtub at the dacha has long ceased to be the only place for maintaining personal hygiene, and a normal modern bathroom at the dacha is becoming more and more common. We want to consider the main ways of organizing the interior and arranging a country bathroom.

Bathroom in a country house

Peculiarities

Previously, most of our citizens perceived a dacha as a large vegetable garden or small garden, and there was no need to talk about amenities. However, today the attitude has changed noticeably, and many want to be able to fully live and relax in their own dacha.

However, suburban housing, as a rule, is less suitable for arranging sanitary facilities and installing equipment for water procedures.

Unlike urban housing, there are the following features:

Absent centralized water supply. To equip a full-fledged bathroom, it is necessary to ensure a supply of usable water, this can be a well, a well or a spring equipped with a pump and pipeline;
There is no centralized sewer system. Used water must be drained away, in addition, it must be purified or disposed of using a sewer. To do this, you should build a drainage system for water from the bathroom into a septic tank or collection tank, where sewage will be cleaned and discharged into the ground or removed by a sewer truck;
There is no specially designated room for water procedures. You will need not only to find a room for a bathroom, but also to prepare it for normal use: waterproof the walls, floor and ceiling, insulate the enclosing structures, install communications, make suitable finishing;
There is no special hood. Good ventilation- a prerequisite for the operation of any premises with high humidity, so you will have to take care of a competent ventilation system.

You should also pay attention to the type of building you have built. Country houses from block containers are very different from capital housing, and these differences must be taken into account. Wooden structures need appropriate processing.

Bathroom furniture should be selected taking into account humidity. Not every product can serve for a long time in a steam room, so it is better to buy specialized varieties.

Important! If it is not used, then the supply and sewage system must have a tap for draining water from the pipes, otherwise in winter they will rupture when the liquid crystallizes.

Varieties

Now let's look at the options for organizing bathrooms that are most often used by modern summer residents.

Summer shower cabin. The simplest and cheap option, which is a small room on the site, equipped with a shower tray and shower. Instead of a pallet they often put plastic baths for a summer residence;
Separately standing sauna or. This is the most expensive option, as it requires the construction of a new premises, purchase or structure furnace equipment, the price of which is very significant, the organization of water supply and drainage;
Bathroom inside the house. The most comfortable and affordable option.

Important! For normal functioning autonomous systems supplying water requires electricity. If you don't have centralized network, renting a diesel generator for your dacha will help you.

Preparing and finishing the bathroom

For those who are planning to work with their own hands, we have compiled small instructions, which will help you understand the basic principles of preparing and finishing a bathroom:

We clear the selected room of foreign objects and furniture, remove old finishes from the walls and floor, and wash off the whitewash from the ceiling;

Dismantling old screed floor and connect the sewer pipe;

We cover the floor with construction polyethylene, lay the reinforcing mesh and fill in a new screed. It is better to use a special mixture for wet rooms;

We lay electrical wiring and water pipes;

We plaster the walls with a special waterproof compound, make a hole in the upper part of the wall for exhaust, and in the lower part of the opposite wall for air supply;

We cover the walls and floor with ceramic tiles, grout the seams with waterproof epoxy grout;

We paint the ceiling with waterproof acrylic paint;

We install the bath. Plastic bathtubs for summer cottages have proven themselves to be quite good - they are lighter and cheaper than cast iron ones. We install a washbasin, a boiler and connect the appliances to the water supply and sewerage system.

Important! Before installing the bathtub, you need to make sure that the ceiling can support its weight, taking into account the weight of the screed and tiles.

The garden design takes on a special charm if there is a small pond. The easiest way to create a miniature pond yourself is to use a used cast-iron bathtub. Let's talk about the rules of installation and design.

Features of creating a mini pond

Original look small mirror receives water through registration natural materials, stones, plants. Night illumination will create a mysterious, attractive atmosphere. Using a container in the form of a cast iron bath to hold water, you can simplify the amount of work on arrangement artificial reservoir, overcome the difficulties of sealing the coating. Installation is fairly quick using available materials. IN further care it is also not labor intensive and simple. If desired, you can grow not only aquatic plants, but also add fish there.

A slight deepening of the edges improves perception and allows you to conveniently place decorative material in the form of stones and plants around the perimeter. If the edge protrudes above the surface, it is better to paint it in Brown color or hide under plants.

It is advisable to choose a place for a pond in a dry area. It would be good if there were trees here, creating shade for several hours. Usually selected cozy corner in the garden next to an apple tree or large bush. Lowland, with stagnant melt water and an area with the presence groundwater not suitable for placing a pond.

Required materials for a bathtub pond:

clay (2 buckets);
tile/tile adhesive (1 packet);
piece reinforced mesh;
container for solution;
metal scissors;
metal wire;
tool for cement works;
pliers, level;
medium and large stones;
crushed stone/small stone (1-2 buckets);
cement mixture(2 packages);
cast iron bath with plugged/cemented drain hole.

Progress

Having decided on the location, you can start digging a hole for the bath. In order not to remove excess soil, the shape of the “pit” should exactly match the container, but a little deeper. Before lowering, the turf around the perimeter is removed with a spade to the sides and down. As a result of immersion, the edges should be approximately 30 cm below the soil level.

During installation, it is important to maintain horizontality; to do this, you need to gradually fill the gaps with sand and compact them evenly on each side, constantly monitoring the process with a level. The backfill ends before reaching the surface by 20 cm.

Next, the tile adhesive is diluted to doughy state and this mass is applied to the walls inside the bath, the bottom remains unused. Try to apply without smoothing, creating natural unevenness.

Then a mesh is lined inside and covered with cement mortar, elements of driftwood and pebbles are pressed in randomly. If desired, shelves are made on the mesh for installation large stones and pots with vegetation. After drying, a thick clay solution is placed on the bottom and left for a couple of hours to dry.

Decorating a pond

To fill, it is better to use a hose and keep an eye on weak pressure, which will not wash out the clay. It’s a good idea to find a natural reservoir and bring aquatic plants and fish from it or with roots; if this is not possible, you can purchase plants and fry at a pet store.

We fill the groove left around the circumference with large stones, so as to create differences in the coastal topography. Now you can drop off moisture-loving plants, arranging according to plan. Relying on your imagination, plant decorative algae inside the pond, fixing the roots at the bottom between the stones, or simply immersing them in weighted pots.

In an effort to get away from the geometry of the bathtub, you need to change the shape of the pond. Asymmetry is introduced by creating different heights relief and forced expansion of the banks. For example, at one end you can arrange a small rock garden, and on the other side create a rocky beach made of pebbles or gravel. Plant bergenia at the edge of one side, which with powerful leaves will change the shape of the reservoir. Availability flat stones will make it possible to create an overhanging rocky shore.

From the vegetation, ground cover, low-growing species and moss. They will disguise the sides and make the shore look natural. Great solution There will be a spreading fern placed on the central point; it will look especially elegant framed by small pebbles. You can arrange a fountain in this pond. Don't forget about the lighting. One or three is enough solar lanterns that will create mystery and emphasize beauty water body at dusk. Any imaginative maneuvers will add uniqueness to your idea.

It is widely believed that relaxation by the water promotes relaxation and has a beneficial effect on the body. To do this, it is not at all necessary to purchase a plot of land near a natural reservoir. If you wish, arrange it yourself decorative pond on a summer cottage using scrap materials is not difficult. Anyone can build a pond from a used bathtub.

The idea of creating a pond from an old bathtub

With the advent of new high-tech materials, many residents of private and apartment buildings replace old ones metal baths new, more modern acrylic or shower stalls. In this case, the problem of disposing of a used bathtub arises. As a rule, this old-school product is made to last, so it can be used for a long time. for long years– for example, on a summer cottage in the form of a mini-reservoir. If you or your neighbors don’t know what to do with a used bathtub, try using this idea and “breathe” into it new life. To do this, you will need to transport such “construction waste” in the form of an old bathtub to your summer cottage in order to try to turn it into a mini-pond.
How to make your own pond from a bathtub

Using the equipment of a pond, you can create a new recreation area at the dacha for the family. A small decorative pond from an old bathtub will fit perfectly into the overall picture garden plot, decorating landscape composition adjacent territory. It’s not difficult to make such a dream come true - to do this, you will first need to learn more about how to make a pond from a bathtub. Various master classes Making a pond from an old bathroom can be viewed on the Internet. A mini-reservoir equipped on your own will decorate the landscape of your summer cottage, and observing the picture of lush greenery at the water’s edge, aquatic plants and, perhaps, even small swimming fish will undoubtedly delight you and your household.

Choosing a site for a pond

First of all, you need to choose the most appropriate place for a mini pond. You should not build a pond in a lowland, damp place where melt and nearby groundwater can accumulate.

According to Feng Shui, it is recommended to use the southern or eastern part of the site to place a reservoir. A flat, drained, dry place with dense soil, including clay and sand, is optimal. It is worth using a shaded area of the garden area; you can also place a mini-pond on sunny side plot - in this case, after equipping the reservoir, it is advisable to plant plants and shrubs near it that will form shade. You should also take into account the following - if there is a layer of snow in the chosen place in winter, the inhabitants of the pond in the form of fish will have a chance of surviving the winter frosts.
Tools and materials

To make a pond from a bathtub with your own hands, you will need the following devices, tools and materials:

Crushed stone (1-2 buckets);

Pebbles, bricks, stones of various sizes;

Cement and sand;

Clay (for planting plants on the bottom of a reservoir);

Container for cement mortar;

Master OK;

Metal grid;

A sheet of tin or an old leaky pan (for drainage equipment at the bottom of the pit);

Cement-based tile adhesive;

Dye or color film;

Roulette;

Building level.

Sequence of work

To transform a used bathtub into an element garden landscape in the form of a mini-reservoir, you will need to do the following sequence of work:

First you need to prepare the bath as suitable container under the pond. For this:

It is necessary to cement the side drainer in the bath. After the cement has dried, you can proceed to the next stage;

Then you will need to give the surface of this container more natural look– to do this, you can cover it with a colored film or paint it in natural tones (beige, grey, black or brown). Or you can treat the surface of the bathtub using a special adhesive composition to give it a natural look. To do this, put on protective gloves, mix ceramic tile adhesive diluted with water according to the instructions with a coloring pigment of a suitable tone - you will get a quickly hardening dough-like mass. Immediately after preparing the mixture, lightly coat the surface of the bathtub from the inside. An uneven, rough layer of such glue will imitate the natural bottom of a reservoir. The bathtub treated in this way should be covered with a rain film on top and left to dry for 24 hours.

While the painted bathtub is drying, you can dig a hole according to its shape. Place the bathtub at the planned location of the pond to mark the location of the pond. To do this, you need to surround the container with small pegs and stretch a rope between them. According to its location, it is necessary to mark the boundaries of the reservoir on the ground, remove the corresponding layer of turf and dig a hole under the pond. It is necessary to select such a depth that the side of the bathtub placed inside is approximately 25 cm below the main ground level.

At the drainage site, you need to dig an additional hole to provide drainage. The excavated soil can be taken away - it will not be needed for further development of the reservoir.

Next, build a funnel for drainage. A sheet of tin rolled into a cylinder or a pan with a hole in the bottom must be placed in the prepared recess and filled with gravel or crushed stone - 20 cm above the bottom of the main pit. This drainage will allow you to drain the water from the bath in winter.

It is necessary to lay a small layer of crushed stone at the bottom of the pit and cover it with a layer of sand - in general, such a coating will be about 20 cm. After this, you need to compact these materials and carefully remove the tin funnel or pan.

Place bricks at the corners of the pit and lower the bathtub into the prepared recess (so that its bottom drain hole coincides in location with the crushed stone drainage). Such transportation will require several strong hands or a winch. Using a building level, level the horizontal symmetry of the upper edges of the container. Add on the sides installed bath sand, moisten it with water and compact it as tightly as possible.

Place a metal mesh on the sides of the bathtub - in a continuous strip or in the form of four pieces along the sides of the bathtub. Coat the mesh with a solution to stiffen the structure, inserting pebbles into it here and there. Using wire on the mesh, you can form rings for further equipment of horizontal shelves in the bath - in the future you can place plants on them. In this way, you can form asymmetrical, more natural outlines of the future reservoir. Wait for the concrete to dry.

Place clay at the bottom of the container of the future reservoir, add a little water and coat the bottom. For high-quality fixation of the root system of aquatic plants, a layer 6-7 cm thick will be sufficient.

Along the perimeter of the pond, carefully remove upper layer turf, lay the reinforcing mesh. Cover this trench with a layer of thick cement-sand mixture, leaving a small groove 30-40 cm deep for planting coastal plants. To decorate the pond, you can place rounded stones, pebbles or flagstones around the bathtub in a random order (so that the edges of the bathtub are covered) and secure them with concrete mortar.

While filling the mini-pond with water, make sure that the soil at the bottom does not erode. You will need to place the end of the garden hose at the bottom of the bathtub and turn on the water so that it flows in a thin stream (to do this, it is advisable to cover the end of the hose with a spray nozzle).

Having equipped such a mini-pond from a bathtub on your own, you can begin to further plant aquatic plants in it and populate it with inhabitants of your choice.
Decorating a pond from an old bathtub with plants

In an earthen groove left along the perimeter of the reservoir, you can plant various perennials, coastal moisture-loving and marsh plants, and also place several large stones there to form the relief of the banks;

Having selected groups of aquatic plants to your liking, plant them in an improvised pond. To do this, you will need to fix the roots of the plants in a layer of bottom clay and stones, place them in flowerpots at the bottom of the bathtub or among small pebbles on horizontal shelves.

For decorative design Small or dwarf water lilies, water lilies, and duckweed are suitable for the surface of the reservoir. Get some money aquatic plants with roots and a formed root ball of silt, you can in the nearest natural body of water. Place fry of small fish from the reservoir (for example, verkhovka) into the water.

It is not difficult to give a reservoir a natural asymmetry by changing the width and height of its banks. You can implement this in the following ways:

Form a mini-beach of crushed stone on one side of the shore;

Post nearby alpine slide or mixborder.

The introduced microorganisms, fish and planted plants will gradually multiply and form the microclimate of the pond on the site. Gradually, the water will lose transparency, and water will appear on the walls of the reservoir. natural plaque. Thus, the artificiality of a man-made pond will not be obvious, thanks to decorative landscaping it will take on a completely natural look.

Useful tips

With the help of a mini-pond from a bathtub it is possible to create with my own hands fantastic at the dacha beautiful corner. When designing it, you can fully use your creative abilities and imagination. Take care of the pond small size on open area not difficult. However, try to take into account some practical advice on design and operation of the pond:

There is no need to try to convert a mini-pond into a country aquarium at fresh air with goldfish and crystal clean water. In addition, crucian carp thrown into a pond will make the water extremely cloudy, since they prefer to dig in the bottom soil;

Verkhovka fish, which actively clean the water surface, are suitable for populating an artificial reservoir;

In a mini-reservoir from the bathtub, you do not need to change the water, you only need to top it up periodically (once or twice a month). The water overflowing over the sides of the pond will be absorbed into the soil;

Cleaning of the mini-pond will be required in case of uncontrolled reproduction of any microorganism or plant in it.

If there are fish in the mini-pond, you don’t need to drain the water from the bathtub in the cold season - the preservation of the microclimate in it will be facilitated by the freezing layer of ice on the surface, the warmth of the deep layer of soil, as well as a layer of snow that protects from frost.

If you want to leave water in a pond for the winter, place several plastic bottles– they will protect the bathtub container from cracking if a significant amount of ice freezes. In a frosty winter with little snow, you will also need to take care of raking a layer of snow at least half a meter thick covering the surface of the pond.
Pond from an old bathtub - photo