Types of curtains for the bathroom and methods of attaching them. How to easily hang a curtain in the bathroom How to secure a curtain rod in the bathroom

Arrangement of a shower room is a troublesome process, involving the decision of the most unexpected questions. How to hang a curtain in the bathroom correctly is not an easy question. The curtain must fit harmoniously into the interior and be attached securely. Few people will like it if the cornice unexpectedly leaves its place of permanent deployment.

• prevents splashes of water on the floor and furnishings;
• zones the space, clearly separating the place where water procedures are taken;
• contributes to the creation pleasant microclimate while taking a shower;
• is integral part decor.

The latter quality is less often remembered. The solution of practical problems comes to the fore, which is quite justified from an operational point of view. A comfortable curtain fits harmoniously into the overall design concept and can act as a buffer between the ceiling, walls, and floor. It all depends on the idea of ​​the project.

Shower curtain - simple, elegant

The fastening of the curtain is important - safety depends on the reliability of the rod's installation. During water procedures, the free edge of the curtain is lowered from the side of the inner side. This is done to prevent water spillage. Then the canvas experiences increased load, additional resistance is created by water flows beating on the surface. These factors must be taken into account when choosing a fastening method.

How to secure a curtain rod

IN construction stores You can purchase two types of holders:

• “spacer” – the cornice is held by an internal spring in a telescopic tube;
• rod with special fastenings.

Cornice “spacer”.

Installation of the first type is simple. Structurally, the rod is a telescopic tube with a spring inside.

Installation is done as follows:

• remove the protective caps along the edges of the rod;
• extend the telescopic tube until both ends of the cornice rest against opposite walls;
• determine the height;
• put on caps;
• string rings, thread the curtain through the eyelets;
• fix the bar at the desired height;
• check the level.

If an error occurs when increasing the length, the problem is simply solved: remove part of the tube with the spring to the end, insert a larger diameter pipe from the opposite side.

How to attach a curtain rod to brackets

The method described above is suitable for a standard situation when, according to the conditions of the problem, regular bath. But the curtain is also necessary for corner bath, it is used to separate the shower area.

When there is no tray, the drain is located on the floor or low above its level - a small “pedestal”, the curtain performs a double function - it replaces the door, and acts as part of the overall decor. It is enough to move it to one edge or move it apart if it consists of two parts, the space will visually increase.

They always try to fit the curtain into the existing interior or develop a project taking this element into account

With this layout, a semicircular cornice is used, which cannot be secured with spacers. Its installation is carried out as follows:

• determine the height - try on the curtain so as not to make a mistake;
• display a horizontal level to prevent distortions;
• the wall is drilled using a concrete drill required diameter;
• drive in a dowel;
• treat the gaps with putty and allow to dry;
• install fasteners;
• hang a cornice or first string a curtain if the model has grommets.

To harmonize the interior, select cornices, rings, clothespins or eyelets of the same color - white enamel, stylized as silver, bronze. This way the corner will look like a single whole.

Selecting a shower area is an effective interior solution

Ceiling cornice and its installation

Recently they have been using ceiling mounting– comfortable, ergonomic, the curtain covers the space from ceiling to floor. Installation of such a cornice is simple. We insert the screws from the fittings kit into the special sockets and attach the cornice directly to the ceiling. This design is good for tall or built-in shower heads, or if you don't want to drill into the tile.

The ceiling cornice will cover the entire shower space right up to the ceiling.

What materials are used for shower curtains?

Waterproofness is a key criterion when choosing curtains. Fortunately, stuffy polyethylene or oilcloth products, ineffective and inconvenient to use, have sunk into oblivion. Today in the production of curtains they use:

• PVC (budget option);
• polyester (more expensive, but better quality);
• vinyl.
• fabric curtains with impregnation.

Polyester is considered the optimal material. A variety of prints look great on it, it is pleasant to the touch, but requires careful care. Dried streaks of water spoil the visual impression when getting acquainted with the original solution.

Kind with healthy. Ideas for prints - very different

Can buy ready product– the market is flooded with canvases with various images, interesting plot drawings, abstractions. If we're talking about about a stylish room, then printing is done on polyester. And then simple curtain will become an exclusive copy.

Fabrics with moisture-resistant impregnation are used for expensive interiors. These are classic, Venetian or rich oriental areas for water treatments and hygiene. This curtain can be washed, its wear and tear is not as great as it might seem at first glance.

Gorgeous fabric with a natural print.

Types of curtain rods for the bathroom: photo ideas

The variety of fastenings does not end with the options - telescopic with brackets. There are many modifications, since the design can be the most unexpected.

For example, a ring cornice looks stylish and neatly zones the shower area.

Cornice - ring.

There are interesting, convenient flexible curtain rods for showers. They are given complex shape when required.

Flexible curtain rod for the bathroom.

A holder (or, as they also say, a rod) for curtains in the bathroom can be installed quite easily, even if you have never done this before. Moreover, the time you spend performing this action will vary from a couple of minutes to half an hour, depending on the barbell design you choose.

Telescopic

Even a teenager can easily install the telescopic rod in place. In addition to the holder itself, you will only need a small stepladder (or a high stool so that you can rise to the height required to install the bar), a tape measure and a pencil, since you can install the bar in the bathroom without drilling holes in the tiles.

• Measure the distance between the walls where the rod is installed. You should not move the holder close to the ceiling; it is better to step back 10-15 centimeters. If you have already bought curtains for the bathtub, then choose the height of the location of the bar, focusing on the length of the curtains (they should be immersed in the bathtub by at least 15-20 centimeters).

• Mark the location where you intend to install the rod on the wall with a pencil.
• Using the instructions included with the barbell, open it to the required length plus 1 centimeter.
• Stand on the stepladder and carefully place the barbell in place. It should be on the marks you made on the walls, and at the same time, both ends should rest tightly against the ceramic tiles.
• Apply light pressure to the center of the rod to ensure it is securely installed.

Telescopic rods are only suitable for bathtubs rectangular shape. However, it is not recommended to install them if the bathroom will be used not only by adults, but also by children, since there is a possibility that while playing in the water, the children will strongly pull the curtains and the holder will fall down with them.

other methods

The second option for attaching a bath rod is a wall mount. Such holders are available not only for rectangular, but also corner bathtubs various sizes. All parts necessary for fastening are sold as a kit.

A little about how to install a bar in the bathroom:

1. Place the purchased holder on the edge of the bathtub (taking into account that the curtain should be in a free position inside the bathtub). Mark the points where the rod touches the wall with a pencil.
2. Using a building level (or focusing on vertical seams ceramic tiles) “move” these points 160-170 centimeters up (here you should proceed from the length of the curtain and the height of the ceilings). If the place where the rod is to be attached coincides with a horizontal or vertical seam between the tiles, move it to one side, otherwise there will be a high probability that a small edge of the tile will break off when drilling holes in it.
3. Remove the end fasteners from the kit included with the rod. Attach them to the wall and use a pencil to mark the places where you need to drill holes.
4. Remove the end pieces, drill holes of the required diameter in the wall and carefully hammer the dowels into them. When installing the rod on plasterboard walls, you will have to use special screws or butterfly dowels.
5. Attach the end pieces and secure them to the wall with screws.
6. Insert the rod into the end pieces.

For corner baths, it is recommended to additionally attach the holder to the ceiling, since simply installing the rod in the bathroom supported by two perpendicular walls will not be very reliable. However, if the ceilings are suspended, it is better to make additional fastening to the wall.

Video

We invite you to watch a video about how to hang a barbell in the bathroom.

Today there is a huge selection of all kinds of curtains for bathrooms on sale, which differ not only in their design features, but also in installation methods. If you are going to do renovations in the bathroom yourself, then the question may arise: how to install a sliding curtain rod for a bathroom? First, you need to decide on the type of curtain you bought, and only then consider options for installation, because soft, sliding, swing curtains can have various options installation

Why do you need a curtain for the bathroom?

This piece of furniture can simultaneously perform several functions:

• Zones the space, separating the place where water procedures are taken.
• Prevents water from splashing onto the floor and furnishings.
• Helps create a good microclimate while taking a shower.
• Is an integral part of the decor

Important! For many, the last point is insignificant - solving more practical problems comes to the fore, which is fully justified. A convenient curtain that harmoniously fits into the overall design concept can act as a buffer between the floor, walls, and ceiling. Everything will depend on the idea of ​​the project.

Fastening the curtain is of great importance - safety depends on the reliability of the rod installation. During water procedures, the free edge of the curtain is lowered from the inner edge. This is done to avoid spilling water on the floor. Then the canvas experiences increased load, because additional resistance is created by streams of water that beat against the surface. When deciding how to install a curtain rod in a bathroom, these factors need to be taken into account.

Sliding cornice: advantages and disadvantages

Barbell sliding type consists of two pipes, one of which has a smaller diameter and is located inside the second, as well as two parts that serve as support points. This structure allows the product to expand to the required length and rest against opposite walls.

Acting like a spacer, such structures are easily installed using fasteners rotary mechanism. Such variants of systems can only be straight, because they require two opposite planes.

Important! Recently, there have been designs in the form of an arc, but such products must have special suction cups, otherwise the cornice will sag under the weight of the curtain.

A sliding bathtub curtain rod has the following advantages:

• Speed ​​and ease of installation of curtain rods in the bathroom.
• Relatively low price for the product.
• Strong enough to withstand a standard polyethylene or vinyl curtain.
• Attractive appearance- the ability to use different stylistic directions.
• The use of the structure does not harm the wall surfaces.

But such systems also have their drawbacks:

• Such curtain rods cannot be used for angular location baths. Since the design is straight, it can only be used in small bathrooms or rooms with appropriate repairs and installation of two planes located oppositely.
• Curtains hung on such systems should not be too heavy, as the product may not be able to support them.
• If mistakes were initially made during the installation process, the cornice will gradually slide down the wall and sooner or later collapse.

Important! In many cases, sliding curtain rods are a great solution. If it turns out that for some reason they are not suitable, you can easily dismantle them and choose some other option. In this case, the surface of the walls will not be damaged, and the cost of the product is not so high that it would be necessary to apply swipe according to your budget.

Materials and shapes of sliding curtain rods

To make sliding curtain rods, manufacturers use the following materials:

• Aluminum is a fairly light and unpretentious material that is not afraid of rust and can withstand standard curtains very well. It's not as durable as stainless steel, but it can last long years without repair or replacement.

Important! It can be painted in any color, which makes it possible to use it in any interior.

• Plastic is today the most common and cheap option. It will not last very long, but since its cost is very low, it can be changed at least every year. The advantages include diversity color solutions, the opportunity to choose a product with a metal, wood or even leather finish.

Important! The obvious disadvantage is short term operation and tendency to quickly become dirty.

• Wood - this option is not used as often as the previous ones, but some are attracted by its originality. Before hanging the curtain in the bathtub on a wooden cornice, it should be treated special composition, which will prevent changes in the structure of the material. Pros: uniqueness, aesthetics.

Important! Minus - in conditions high humidity bathroom, can swell over time, and such products are not cheap.

Installation of a sliding cornice

In order to correctly install the telescopic rod in the bathroom, you will need a pencil and it is advisable to use building level. You need to act like this:

1. Mark the location of the device with a pencil. At this stage, you need to know how to hang the curtain correctly: its bottom edge should go down into the bathtub by about 20 cm.
2. Print the packaging and extend the bar to a length equal to the distance between the walls of the room, plus 0.6-1 cm.
3. String rings or permanent hooks onto the tube.
4. Fix the rod at the marked places.

Important! The final horizontal position of the cornice is determined using a building level.

Installation of cornice on brackets

The method described above for installing a cornice in suitable for a bathroom for a standard situation, in an ordinary bathroom. But a corner bath also needs a curtain to separate the shower area.

When there is no tray, and the drain is located in the floor or low above its level - on a low “pedestal”, the curtain performs a double function:

• acts as part of the overall decor;
• replaces doors.

It is enough to open the curtains or move one edge, and the space will immediately increase.

With this layout, as a rule, a semicircular cornice is used, which cannot be secured with spacers. Its installation is carried out as follows:

1. Determine the height - try on the curtain so as not to make a mistake.
2. Bring out a horizontal level to prevent distortions.
3. Drill into the wall using a concrete drill of the required diameter.
4. Drive in the dowel.
5. Fill the gaps with putty and let dry.
6. Install the fasteners.
7. String a curtain onto the curtain rod, if the model has grommets, and hang the curtain rod.

Important! To harmonize the interior, it is advisable to select cornices, clothespins, rings or eyelets of the same color - white enamel, bronze, silver stylization. This way the corner will look like a single whole.

Ceiling cornice and its installation

Recently they have often started to use ceiling installation cornice in the bathroom. It is convenient, ergonomic, and the good thing is that the curtain covers the entire space from floor to ceiling.

Installation of this version of the cornice is quite simple. To do this, you need to insert the screws from the hardware kit into special sockets and attach the cornice directly to the ceiling.

Important! This design good for tall or built-in shower heads or when you don't want to drill into the tile.

The first step for equipping the bathroom has been taken - the bathtub has taken its place, which has become the central element of the room. Mixer installed. There are little things left: arrange bath products and limit the area from splashing. And this requires a curtain that cannot be hung without a curtain rod. But installing a curtain rod in a bathroom, despite the apparent simplicity of the work, can cause many problems.

How to hang a curtain rod in the bathroom

The standard version of the cornice is plastic or metal pipe usually 25 mm in diameter, which is attached to the walls of the bathroom. There are several mounting options. The simplest one, as they say, is just right. The simplest design, which is easy to install, but it may not be able to withstand heavy curtains. Cornices produced by Aquanet are mounted to the wall using two fastening elements - brackets, for installation of which self-tapping screws are used. The bracket itself is covered with a decorative reflector.

Installing the cornice is not difficult. To do this, you need to have a tape measure, a pencil, a hammer drill with drills, as well as a screwdriver or Phillips screwdriver. All curtain rod components from Aquanet are made of stainless steel and meet sanitary and hygienic requirements.

So, stock up on everything you need. What to do next...

Attach the curtain rod to the bathtub.

Move the decorative reflectors to the center of the cornice, using a pencil to mark the points where the cornice meets the wall.

Mark the installation points for the cornice. To do this, measure the required distance vertically from the edge of the bath. To calculate it, you need to determine what the height of the cornice in the bathroom will be. It depends on the size of the curtain. Standard height curtains - 180-200 cm. Its edge should be about 20 cm below the level of the bathtub to prevent splashing of water. Accordingly, subtract 20 cm from the height of the curtain and measure the resulting distance from the edge of the bathtub upward. This must be done on both sides. These will be the points where the center of the bracket should be located.

Attach the bracket to the marked mark so that its center coincides with the received mark on the wall.

Mark the holes for the dowels through the holes on the bracket. Aquanet curtain rods should have four of these.

Insert plastic dowels into drilled holes so that a part of the dowel approximately 0.5 mm long protrudes from it.

Place the cornice on the glass of the bracket, and then secure the structure to the wall with screws.

After completing the installation, move the decorative reflectors to the walls, covering the brackets with them.

Advice! To install a cornice on a tile, holes in the tiles should be made not with an ordinary drill, but with special ones.tungsten carbide, intended for glass and tiles, which have toopium-shaped, which is why they are also calledfeathers. They must be selected according to the size of the screw. In this case, it is better to drill in the center of the tile, at least at a considerable distance from the edge; if the hole is closer to the edge of the tile, then there is a greater likelihood that a piece of tile will break off.

How to install a sliding curtain rod for a bathroom

A slightly different procedure will be required if a sliding cornice is purchased.

They come in two types. The first one consists of tubes that are inserted into one another, which is why such a cornice is also called telescopic. It varies in size from 1.3 to 2 m, so it will fit bathtubs of different lengths. The second has a spring mechanism that allows you to hold the cornice on the wall using spacers (they can be located on both sides of the cornice or on one) equipped with springs. It is unlikely that anyone will have a problem with how to hang a curtain rod in the bathroom if they purchased just such a design. A cornice of this type can simply be moved from both sides or one, squeezing the springs, and when installed at the marked points, release it so that the spring firmly presses the ends of the cornice in the required places.

To be fair, it should be noted that such options for installing cornices are only suitable for the standard straight shape. They are used when installing a rectangular, or less often oval, bathtub. This design cannot be called reliable. If you suddenly pull the bathroom curtain towards yourself, for example, you accidentally step while getting out of the bath, and the curtain rod will fall down. And in the case of covering the walls in the bathroom with plasterboard, the cornices similar design and it is not recommended to use it at all. They won't hold on.

Advice! When purchasing a telescopic curtain rod, pay attention to the plugs at the ends of the pipe. The most acceptable option is rubberized elements. They do not slide down the tiles as easily if the curtain is pulled forcefully, like plastic ones, and they don’t damage the walls if they are covered with paint, like metal ones.

And if the bathtub is corner or has a complex configuration...

An ordinary straight cornice can hardly be adapted for a corner or asymmetrical bathtub. It is ideal if it follows the line of the bathtub edge, no matter how intricate it may be. That is why the Aquanet company offers a curtain rod for almost every bathtub model with an original configuration, such as Borneo or Bellona. All of them have a complex shape, but at the same time the method of fastening similar to that, which we have already talked about.

Questions often arise about how to secure the curtain rod in the bathroom so that it does not sag under the weight of the curtain. This usually applies to corner L-shaped or semicircular cornices. It all depends on the material from which the model is made. So, an all-metal stainless steel cornice, which wide range offers the Aquanet company, it can easily withstand the weight of the curtain, no matter what material it is made of: fabric or polyethylene. Additional fastening at the pipe turning point is not required, since the structure is quite rigid, and fastening to the walls with self-tapping screws ensures reliable installation. It is, of course, undesirable to use such a cornice as a horizontal bar, but for a curtain this is the most suitable option.

Cornices of this shape are often made of aluminum. This material is more susceptible to deformation than stainless steel. Here it can just sag over time from the weight of the curtain. The only advantage of an aluminum cornice is that it bends well and you can adjust the shape of the cornice to fit a specific model. However, this is a very dubious advantage.

Advice! When choosing a cornice made in the shape of the letter “L”, carefully inspect the place where the pipe turns. There should be no folds, metal deformations, and especially no cracks. All this indicates that the metal used to make the cornice is low grade. There is a danger that rust will appear on it, and cracks will become deeper during operation and will lead to rapid failure of the product.

Despite the popularity of glass and plastic bathroom curtains, the demand for them is only growing. This is explained not only affordable price and ease of use - correctly selected curtains play an important role in interior design. But even the most beautiful canvas needs to be hung skillfully, otherwise it’s unlikely to achieve the desired effect. And here the cornice or rod for the curtain in the bathroom comes to the fore - it seems simple and discreet, but such an important accessory.

For the curtain to look harmonious, the cornice must follow the shape of the bathtub. And bathtubs are now quite diverse: in any plumbing salon there are models of rectangular, round, oval shape, as well as angular and asymmetrical. That is why the range of rods is also quite impressive, and making a choice is not at all easy.

Types of rods by shape

1. . These are standard models that are mounted horizontally between two opposite walls. They have the simplest design and differ from each other only in length and diameter.
2. . These include semicircular, arched or L-shaped models. Designed for corner baths, they make it possible to completely close the space on both sides.
3. . The most decorative models, designed to be used separately standing bathtubs or completely open shower. Eat combined options, on which the overhead shower and curtain are simultaneously attached. They look very stylish, unusual, and easy to use.
4. Special rods. These products are intended for designer baths Asymmetrical in shape, they are made mainly to order and are exclusive models.

By material

1. . Plastic products are the most inexpensive and lightweight, and have the greatest variety. color range. Curtain holders move along such curtain rods almost silently. In this case, curtains must be hung only from lightweight materials, otherwise the rod will begin to sag. Over time, the color of the coating becomes faded, microcracks and ring marks appear on the surface of the rod.
2. . More durable and durable, at a price slightly more expensive than plastic ones. Have attractive appearance, are resistant to temperature changes, washing, corrosion and mold, but under the influence of loads they can become deformed. In addition, hollow aluminum rods amplify sounds, and therefore it will not be possible to quietly close or open the curtain.
3. . Most durable option. Such rods are not subject to deformation even under increased loads; they retain the smoothness and shine of the surface for years. They are not afraid of corrosion, fungi, and are easy to clean from plaque. Steel rods are more expensive than others, but they are well worth their price.
4. Combined. This type of cornices is made of metal and covered with a special plastic that is resistant to various types of influences. Such rods do not bend under loads, do not lose their aesthetic qualities for a long time, and do not make noise when the rings move.

By mounting method

Telescopic method. Suitable for straight rods only Not large sizes. The telescopic design allows you to select the desired length of the cornice and secure it using a spacer or spring mechanism between opposite walls.

• Pros: No installation required accurate measurements and drill the walls, installation takes a couple of minutes. If necessary, the bar can be easily moved higher or lower.
• Disadvantages: this type of fastening is not the most reliable - pull the curtain hard enough and the rod may fall. For this reason, it is not recommended for families with small children.

Fastening with dowels. This reliable way, and it is suitable for rods of any size and configuration. Most often, rods are attached to the walls, sometimes only to the ceiling, and products of large sizes and complex shapes are simultaneously fixed to both the walls and the ceiling.

• Pros: the screwed rod will never fall, the choice of cornice is not limited a certain form and dimensions.
• Cons: installation requires tools and skills to work with them, as well as accurate measurements. If you subsequently need to rehang the bar, you will have to seal the holes from the fasteners in the walls and ceiling.

Design features

Each type of barbell has its own design features, affecting the type of installation. Straight rods are divided into three types:

• telescopic– are a two-tube design various diameters and a turning mechanism. The smaller tube is located inside the larger one, and during installation it extends to the required length, and the mechanism ensures reliable fixation in this position;

  Telescopic rod for bath curtains 80-140 cm

• expander cornice– a variant of a telescopic rod, only instead of a rotating mechanism, springs located at the ends of the product are used;
• fixed length rods– are a tube with flanges and decorative caps at the ends. Fastening is done using flanges on dowels, and caps cover the fastening elements, increasing the aesthetic appeal of the structure.

All curved models are divided into rigid and flexible. Rigid ones consist of hollow metal and plastic tubes different sections. The shape is given to them at the stage of manufacturing the rod, and the only thing that can be adjusted during installation is the length. When adjusting the cornice to the size of the bathtub, the excess is simply cut off.

For the manufacture of flexible rods, a special aluminum profile or aluminum tape is used. There are also plastic options, but they are not very suitable for the bathroom. Such products are easy to give the required form, so they are ideal for non-standard asymmetrical bathtubs. Of course, their cost is much higher than tubular models, but the demand for them is quite high.

Concerning corner models, then they can be solid or prefabricated. Small rods are made from a whole piece of tube or profile. They are reliable, durable, and do not require additional fastenings. Prefabricated structures consist of several parts that are tightly connected to each other. This makes it possible to easily reduce the length of the rod if necessary, but requires the presence of ceiling hangers. Without them, the product will sag under load, and most of all - at the joints.

Manufacturers of curtain rods

On the domestic market, rods for bathroom curtains are represented by a large number of manufacturers, because this accessory is quite in demand. Not the last place Russian brands, whose products meet the highest requirements, although they are not very diverse. To make your choice, it is worth studying in more detail the range and main characteristics of popular models.

bathroom curtain rod

Boom installation technology

Installing a rod is a fairly simple process, but it also has certain subtleties. Below are options for installing cornices in spacers and on flanges, with ceiling hangers. The nuances of fastening to concrete walls, tiles, drywall and plastic sheathing will also be considered.

Installation of a straight rod in a spacer

To work you will need a tape measure, a level, a pencil and the bar itself.

Step 1. Based on the length of the curtain, select optimal height for the rod. The bottom edge of the curtain should freely fall into the bathtub by at least 20 cm to avoid splashing water, and there should be a distance of at least 15 cm between the rod and the ceiling. Measure the required height with a tape measure and mark a point with a pencil. Place a mark on the opposite wall in the same way.

Step 2. Unpack the rod and be sure to read the manufacturer's instructions to avoid installation errors. Check how the mechanism works.

Step 3. Extend the tube to the required length, add another 1 cm, string the curtain rings if they are not removable.

Step 4. Lift the barbell and carefully place it in place, bringing one end in first and then the other. Place a level on top and make sure the cornice is positioned exactly horizontally. If it is not, correct it by applying pressure at the base. Then press lightly with your hand in the center - a properly secured rod should not move a millimeter. After that, all that remains is to hang the curtain.

Mounting the rod on flanges to a concrete surface

To work you will need:

• drill;
• screwdriver;
• tape measure and pencil;
• level;
• rod and dowels with self-tapping screws, which are included in the kit.

Step 1. Unpack the rod, check the presence and integrity of all elements. Select a convenient mounting height, taking into account a 10-15 cm wide gap between the ceiling and the rod. Now attach the rod at the desired height to the wall surface and determine the attachment points. The structure should be positioned so that the curtains can completely cover the bathtub, but do not interfere water procedures. Mark the fastening points with a pencil.

Important! Before starting work, you should make sure that there are no electrical wiring, water pipes or other communications in the areas where you intend to drill. You can check this using special device– a household hidden wiring detector.

Step 2. Using a level, check the position of the marks relative to the horizontal, and correct them if necessary. If the distance between the marks is large, it is most convenient to use a water level.

Step 3. Next, take the first flange and attach it to the wall so that the mark is exactly in the center. Using a pencil, mark drilling points through the holes on the flange. Do the same on the other side.

Step 4. Now, using a drill with a hammer drill mode and a concrete drill, make holes the size of the dowels at the marked points. The diameter of the drill must match the diameter of the dowel. Typically, the rod comes with self-tapping screws and dowels measuring 6 mm. The depth of the hole should exceed the length of the fastener by approximately 5 mm. Typically, standard round flanges have three holes.

Step 5. The holes need to be cleaned of dust, dowels inserted there, and hammered in tightly. Next, attach the flange again and screw it with self-tapping screws. The flange is secured on the other side in the same way.

Step 6. D Next you need to take the bar, put silicone liners on both ends, and pull decorative caps on them so that they are each turned in their own direction. If the rings for the curtain are non-removable, they need to be threaded before attaching the second cap.

Step 7 Now loosen the clamping screws on the protruding part of the flanges, insert the ends of the rod one by one. Tighten the clamping screws until they stop on each side, and push the decorative caps close to the wall surface.

Rods are mounted on brackets in a similar way - first the brackets are attached to the wall, then the ends of the rod are inserted into them. The main condition is to accurately take measurements, because correcting errors will not be easy.

The main difference here is the presence of a ceiling suspension, otherwise the procedure for attaching the rod is almost the same as for previous version. Hangers, mounting rings, and additional screws and dowels are usually included with the rod.

Step 1. Assemble the barbell by inserting straight tubes into corner elements. Try the product on the wall; if the rod is too long, cut off the ends.

Step 2. Put both brackets on and lightly fix them on the rod with screws. Place it on the wall at the required height, check the horizontal level, and mark drilling points through the holes in the brackets.

Step 3. Remove the brackets from the cornice and put everything aside for now. Next, holes are drilled with a diameter of 6 mm and a depth of 40-45 mm, dowels are inserted and hammered in with a hammer.

Step 4. The brackets are individually screwed to the walls with self-tapping screws, a fastening ring for the ceiling suspension is put on the rod, the ends of the rod are inserted into the brackets and secured with screws.

Tighten the screws. Scheme

Step 5. A fastening attachment with holes for self-tapping screws is screwed onto a thin metal tube with a thread that acts as a suspension. Apply it to the rod so that the nozzle rests on the ceiling, and the tube itself adjoins the rod at a right angle in the bending area. It is the corner area that most needs additional support. Mark the cutting point on the tube with a pencil and saw off the excess.

Step 6. The free end of the tube is inserted into the fastening ring on the rod, clamped with a screw, after which the suspension is lifted vertically and pressed against the ceiling. Drilling points are marked through the holes of the nozzle, then holes are made, dowels are driven in, and the suspension is screwed to the ceiling.

If the rod is too long or has a more complex shape, you will need not one, but 2-3 hangers, located at an equal distance from each other. This method suitable not only for concrete ceilings, and for plasterboard surfaces, as well as covered with plastic. The features of such installation will be discussed below. The only exception is stretch ceiling, and in this case it is necessary to use other fastening options.

A U-shaped rod is also mounted according to the angular type. The only difference is that both ends are fixed on one wall. Typically, small models have only a wall mount that can easily withstand a load of 4-6 kg. But keep in mind that this requires a very strong, reliable foundation - hang the bar only on drywall or plastic panels it is forbidden.

Installation of flexible profile

Installing an aluminum flexible curtain rod is also not particularly difficult. To give the product the required shape, you must first draw a template. A large piece of thick cardboard is suitable for this. Place its edge against the side of the bathtub and trace the outline, making small allowances along the edges - 2-3 cm.

Step 1. Take the profile in your hands, press in the middle with your knee and bend it little by little. The material bends quite easily, so try not to press too hard. As you work, constantly try on the profile against the template so that you don’t have to straighten excessively bent corners later.

Step 2. The finished profile must be attached to the wall and the mounting locations must be determined. If the profile consists of several parts, they are fastened together using special plates that come with the cornice.

Step 3. Attach the brackets according to the marks and mark points on the wall through the holes with a pencil. Drill, insert dowels, screw the brackets to the wall.

Step 4. Now take the hangers, put the fastening attachments on them and attach them to the fixed brackets so that the attachments rest tightly against the ceiling, and the lower ends are located at the level of the profile fastening. Since the tubes are quite long, you will have to cut them, and to do this, mark the cut line with a pencil.

Advice. To increase the security of the attachment, drill a hole in the tube for the clamping screw located at the bottom of the nozzle. When tightened, the screw will enter the tube, and it will not be able to slip out even with increased load on the cornice.

Step 5. Insert curtain hooks into the profile, lift the structure and insert its ends into the brackets. Secure them with self-tapping screws on the bottom side.

Step 6. Insert the hangers into the holes on the connecting plates, screw them lightly and mark the mounting points on the ceiling. Drill, secure the dowels, and then insert the attachments into the hole long screw and use a screwdriver to fix it to the ceiling. Now you need to insert the tube all the way and tighten the screw. Secure the remaining hangers in the same way.

Step 7 The free end of the hanger should fit into the hole on the connecting plate. To do this, the profiles are moved apart a little, the end of the tube is threaded through the hole, and they are fixed with self-tapping screws on the bottom side of the profile.

After this, all that remains is to move the profiles back so that there are no gaps left, and screw them to the plate with screws through the corresponding holes along the upper edge.

Features of installation on different surfaces

On concrete walls lined with tiles

To secure the rod to the tile, you first need to make sure that the cladding is strong. If the tiles are weak, the seams are crumbling, traces of fungus are visible on the surface, you cannot attach anything to the wall. First you will have to dismantle poorly secured elements, remove any remaining glue, clean out the seams and re-face everything.

How to drill tiles in the bathroom

Everything else is done according to the technology described above.

On drywall under tiles

As a rule, walls and partitions made of plasterboard adjacent to the bathtub are tiled. Paint and waterproof plaster under direct exposure to water cannot provide reliable protection this material, unlike tiles. But this design makes it a little more difficult to attach accessories, as it requires special care.

Instead of standard dowels, butterfly dowels are used.

If the rod is large and heavy, the fasteners in the drywall will not withstand the load and will become loose over time, which means you need to drill deeper - to concrete base. In this case, fasteners are also needed long length, taking into account the thickness of the drywall, tiles and the gap between the plasterboard and the wall. The kit usually includes self-tapping screws measuring 5x40 mm, so you will need to purchase separately self-tapping screws of the same diameter, but 80-100 mm long. The dowels, accordingly, should have a diameter of 6-8 mm and a length of 80-100 mm.

The marking is carried out as standard, as on other surfaces. A drill should be at least 10 cm long and must be sharpened. You need to drill at low speeds (1000 rpm), holding the tool firmly and preventing it from slipping. Having drilled through ceramics and drywall, the drill is changed to a Pobedit one and continues to go deeper into the concrete. After this, the rod is mounted on the dowels.

After tightening the self-tapping screw, you get this kind of stop on the back side

On plastic panels

Installing the rod on plastic-lined walls is quite simple. Plastic is not afraid of vibrations and is easy to drill. Here, too, you need to use long dowels, since you cannot attach the rod to the plastic itself - it simply will not withstand the load from the cornice and curtain, and the fasteners will tear out of the sheathing. So, take a regular drill and make neat holes in the plastic at high speeds. Then Pobedit drill in hammer drill mode they drill concrete. When fixing the product with self-tapping screws, it is very important not to overtighten them, otherwise the plastic will be deformed and may subsequently crack.

If you plan to install the rod in a spacer, keep in mind that thin plastic will bend and be pressed under such influence. It is best to prepare a stop for the rod at the stage of wall covering: at the location of the rod, fix two strong boards on the wall to the thickness of the sheathing. Otherwise, to avoid pushing through the plastic, the rod will have to be mounted on dowels.

When choosing a curtain rod for the bathroom, you need to consider first of all the quality and durability of the product. In order not to change the barbell every 3-4 years, pay attention to steel and metal-plastic models. Inspect them carefully before purchasing: there should be no scratches, abrasions, or other defects on the surface, and the parts should fit tightly at the joints, leaving no gaps. Be sure to check the package contents, availability of fasteners and manufacturer’s instructions.

As for design, a lot depends on the interior of the bathroom. All accessories must be in harmony with each other and match general style registration If the faucets and cheap stand are metal and made in retro style, then plastic colored rods do not match them in any way. The shape also means a lot: in a spacious, light bathroom, rods with curly curves and ring options look advantageous, while straight models are more suitable for small rooms.

Curtain rings also come in a wide variety of shapes and materials. The most practical are metal rings with polymer coating. Ordinary metal rings rattle, leave abrasions on the rod, and do not glide smoothly. Plastic does not last long and quickly loses its visual appeal. But metal with a polymer coating does not have such disadvantages, so using such rings is very convenient.

Video - Installation of a flexible rod