Bass bathtubs (acrylic), Bass models (38 photos): Laguna, Nicole, Alegra, do-it-yourself installation: instructions, photos and video tutorials, price. All the secrets of installing a screen on an acrylic bathtub. Features of installation on rectangular corner models How to install on a corner

Instructions for acrylic bathtubs from Bas

Thank you for purchasing the BAS brand bathtub.

• Preface

Bathtubs "BAS" are modern technologies and original lines that ensure the comfort of taking water procedures.

This manual describes the bathtubs' functions, installation requirements, care and operating methods.

Attention: In order for the bath to be beneficial for you, to work for a long time and reliably, a number of conditions must be met:

1) Consult your doctor to what extent taking a bath is beneficial for you.

2) Consider installing filters for water purification.

3) Do not turn on the hydromassage without filling the bathtub with water!

4) It is prohibited to seal the seams between the wall and the bathroom with hard building materials (ceramic tiles, curbs, mortar, etc.)

• Technical description

Standard equipment for a hydromassage bath:

1. Acrylic bathtub - 1 pc.

2. Metal frame - 1 pc.

3. Legs - 4-8 pcs. (depending on model)

4. Panel clamp - 2-4 pcs.

5. Self-tapping screws for fastening the acrylic panel - 5-12 pcs.

6. Additional equipment: acrylic panel (screen), drain-overflow device, back massage, aeromassage, etc. (at the buyer’s request)

Transporting bathtubs When transporting and installing the bathtub, care must be taken not to damage the piping and electrical systems. DO NOT: carry the bathtub by the piping and electrical wiring. It is necessary to avoid mechanical damage to the bath body and screen, and also to exclude the effect of chemically active reagents on the surface of the product.

Instructions for preparing a site for installing bathtubs:

1. A plumber performing work on hot and cold water pipes must take into account the linear dimensions of the bathroom. Otherwise, the pipe outlets may rest against the stiffeners, units and fittings of the bathtub. This means that the bathtub cannot be installed close to the walls.

2. The bathroom drain pipe should not rise above the floor by more than 10 cm. If this cannot be ensured, then a podium must be made.

3. The legs serve to level the bathtub, so additional supports must be installed under the supporting structure of the bathtub.

4. Electrical wiring for the bathtub equipment must be made with a double-insulated cable with a cross-section of 2.5 mm2.

System protection should be based on differential (multiple) shutdown (1fn=30 mA). The power cable must comply with EEC regulations and standards

• Electrical system

The installation of the electrical system must be carried out by a professional electrician with an electrical safety clearance group of at least group 3. The electrical wiring for the lighting and hydro-air massage system of the bathtub must have a “Residual Disconnection Device” (RCD) with a rating of 30 mA.

• Attention:

Connect the electrical cable in the following order: blue wire - “zero” brown wire - “phase” yellow-green wire - “grounding” The power supply for the lighting and hydro-air massage system of the bathtub should be connected only through a separate RCD with a rating of 30 mA. The RCD must be located outside the bathroom. It is strictly prohibited to connect the power supply to the lighting or the hydro-air massage system of the bathtub through a plug and socket.

Using the lighting system without water in the bath is strictly prohibited.

• Name V Hz kW
• Hydromassage 220/240 50 0.9-1.5
• Air massage 220/240 50 0.7-0.9

Power is indicated depending on the bath model.

• Equipment for hydro and aeromassage includes:

1. hydraulic pump

2. compressor for air massage

3. function activation buttons and hydromassage power control

4. hydromassage jets (back side)

5. piping system

• Optional equipment

aeromassage (the jets are at the bottom of the bath)

hand shower, cascade, mixer

backlight

back massage

headrest

pen

• Bathtub Installation Guide.

1. Before installing the screen, first mark the location of the centers of the screen mounting plates on the front side of the bath with a pencil or felt-tip pen.

2-5. Next, you need to screw 4 M 12 nuts onto the mounting legs, use two M 12 nuts to screw the mounting legs to the bathtub frame, and use the remaining two M 12 nuts and two M 12 washers to secure the screen mounting corner on the mounting leg so that it reaches the edge of the screen . Attach the screen to the bath and use a drill dia. Make 3.5 mm holes in the corners of the screen mounting (it is recommended to perform this operation after first removing the screen).

6-7. Mark on the top of the screen the points with the centers of the screen mounting plates already marked on the front side of the bathtub, placing them at a distance of 1.5-2 cm from the lower edge of the front side of the bathtub. In the marked areas of the screen, use a drill with a diameter of 3.5 mm to drill holes for self-tapping screws. Next, use the same drill to make holes in the mounting plates of the screen (it is recommended to perform this operation after first removing the screen).

8. Using the legs, adjust the bathtub to the height of the acrylic panel, taking into account the zero level of the upper plane of the bathtub.

9. Install the drain and overflow device on the bathtub, screw on the siphon (not included) and connect to the bathroom drain pipe

10-11. Having aligned the screen with the bathtub embedded parts, it is necessary to screw self-tapping screws into the holes, and then put plugs on them.

12. After installing the bathtub, remove the protective film.

13. Install the bathtub wall bracket. A wall fixing is offered to enhance the rigidity of the bathtub.

• ATTENTION:

It is prohibited to seal the seams between the wall and the bathroom with hard building materials (ceramic tiles, curbs, mortar, etc.) If the above is not observed, warranty repairs will not be carried out

Instructions for using hydro-, aero-massage, back massage, water illumination (mechanical activation of functions).

• Buttons for turning on hydro-, aero-massage, water lighting. (on and off - by pressing your finger inward)
• Switch for hydromassage and back massage. (simultaneous operation of functions is possible)
• Power regulator for hydromassage and back massage. (turn the knob clockwise)

Electronic (touch) control of hydro-, aero-massage, chromotherapy functions. (1, 2 — air massage power control; 3 — on/off air massage function; 4 — on/off hydromassage function; 5 — on/off chromotherapy function)

• The hydromassage and chromotherapy functions are automatically turned off if there is no water in the bathroom. The air massage is turned off manually after the jets have been purged.

Bathroom care

When cleaning the bathtub, use a liquid cleaner that is harmless to acrylic and plastic surfaces (see cleaning product instructions). The manufacturer offers you a specialized cleaning agent “TIM-PROFI”, adapted to our products. Clean stains with a soft cloth.

Scratches or burn marks from cigarettes that appear on the surface can be removed by lightly sanding with sandpaper (No. 1000/2000) and water. You can restore the shine of the surface with a liquid polish.

• Cleaning the Bath Hydraulic System

This type of cleaning is performed using hard water (over 15 salt deposits per cubic meter of water). It is recommended to clean the bathtub hydraulic system at least 2 times a year as follows:

1. Fill the bathtub with hot water (40C).

2. Pour in liquid detergent at the rate of 2g per 1 liter of water and run the hydromassage for about 5 minutes.

3. After this, turn off the electric pump and drain the water from the bath.

4. Fill the bathtub with cold water again and turn on the hydromassage for 2 minutes.

5. Drain the water and wash the bathtub (see “Bathtub Care”).

The manufacturer offers you a specialized cleaning product for the hydraulic system, adapted to our products.

WARNING: Never use metal brushes or tools, or solvents or detergents containing abrasives to remove dirt from the surface of the hot tub. Also avoid contact of ammonia or chlorine with brass and chrome parts of the bathtub.

• How to use hot tubs

It is prohibited to turn on the hot tub when the hydromassage jets are closed and the water level is 5-6 cm below the jet opening. Never use the bathroom after taking alcohol or taking medications. Hydromassage for medicinal purposes can only be performed on the advice of a doctor, who will select the appropriate duration of sessions and water temperature for you.

Taking a cold bath improves your health. A warm or slightly hot bath relieves tension. To relax muscles and relieve pain, take a bath (up to 40 C). The first hydromassage session, which should be carried out only in warm water, should last no more than 10 minutes. The effect of water jet massage is directly proportional to the temperature of the water and the duration of the session. After taking a bath for too long, you may feel tired. And if you feel sleepy while taking a bath, turn off the hydromassage device for a while and cool the water.

For overweight people, hydromassage baths at water temperatures exceeding 38 C are contraindicated.

Before turning on the whirlpool system, make sure that the jet nozzles are not pointing upward.

• The simplest malfunctions, their possible causes and solutions.

The manufacturer reserves the right to make changes to the design and configuration of bathtubs.

In winter, the product is installed in a warm room after 6 hours from the moment the bath is delivered to the client

If a drain or overflow is installed in a manner not provided by the manufacturer, the bath will be void of warranty.

Active chemicals that could damage the acrylic layer are not allowed to come into contact with the surface of the product.

High (above 80C) thermal effects on the surface of the product are prohibited.

Installation (installation) of the bathtub (shower curtain) and the equipment included in the kit is carried out by the buyer with the involvement of specialists licensed to carry out this type of work. The installation warranty is provided by the installer with a note in the warranty card.

Installation of products should allow easy access to components and assemblies of attachments, as well as to connecting hoses for water and air supply.

Dear buyer! The manufacturer sets the warranty period for bathtubs to 10 years. This warranty period covers all equipment, except for: drainage and overflow devices, hydromassage, air massage and any other additional equipment (see paragraph 7, page 1 of this manual), for which the warranty period is 2 years.

• Warranty service is not provided in the following cases:

– non-compliance with installation rules and operating conditions;

– loss of a receipt or warranty card;

– negligent storage or transportation by the owner, trade or transport organization;

– attempts at unqualified repairs;

– mechanical damage, traces of exposure to chemicals and abrasives due to improper care of the product;

– making corrections to the text of the warranty card;

– the RCD (residual current device) is not installed, if there is electrical equipment on the bathtub;

– use of the product for business activities.

The company does not assume responsibility for damage caused during transportation and delivery.

Warranty service does not include reimbursement of installation and disassembly costs.

• Video instructions for assembling the frame of an acrylic bathtub Bas

BAS brand products are fully certified and labeled. Acrylic and hydromassage bathtubs, shower cabins BAS have proven themselves excellent in Russia and the CIS countries. The reason for this is the impeccable quality and reasonable price. Today this is the best offer in terms of price/quality ratio.

BAS brand products are fully certified and labeled. Acrylic and hydromassage shower cabins BAS have proven themselves excellent in Russia and the CIS countries. The reason for this is the impeccable quality and reasonable price. Today this is the best offer in terms of price/quality ratio.

All products are manufactured on Italian equipment from sheets of Sanitary Acrylic/ABS multilayer polymer material from the Austrian company "Senoplast" on Italian vacuum forming equipment. Bathtubs and shower cabins of the world famous brands “Jacuzzi”, “Teuco”, “Albatros”, “Villeroy&Boch” are made of the same material.

In Europe and other Western countries, BAS have long earned consumer trust. Cast iron and steel bathtubs are a thing of the past because they are inferior in many respects. Acrylic bathtubs are more resistant to mechanical damage, are much easier to clean and do not lose their color over the years. In addition, they are very pleasant to use and retain heat well while taking a bath.
BAS acrylic bathtubs come in a variety of colors, which helps you choose the one that best suits your bathroom design.

If you want more than just a bath, BAS hot tubs are available. By purchasing a hot tub, you will have a personal medical office. Hydromassage relaxes, improves blood circulation, and even improves immunity. It is used for both medicinal and cosmetic purposes. The BAS hot tub is not only useful, but also brings a lot of pleasure.

So, you have decided to purchase an acrylic bathtub. Perfect solution! In this article, we will give you the 5 most important tips that will help you make the right choice so that your bath will give you only pleasure and benefit for many years to come.

When choosing an acrylic bathtub, everything depends only on your desires and financial capabilities. In order not to get lost in all the variety of bathtubs that currently exist, it is worth understanding a few key points that will make your further search easier.

Tip 1: Prices vary
Like any product, acrylic bathtubs vary in price. Nowadays there are a large number of manufacturers of acrylic bathtubs on the Russian market, offering from the cheapest to the most expensive models. The price of a bathtub is influenced by the quality, size of the bathtub, and its design. The lower price limit for an acrylic bathtub is now about 8 thousand rubles. The upper one has practically no limit.

Tip 2: Make your design dreams come true
One of the main advantages of acrylic bathtubs is the wide variety of designs. Your acrylic bathtub can be of almost any shape, from the classic rectangular to the unusual asymmetrical one. This variability allows the buyer to install a bathtub even in the smallest room, as well as to implement any design ideas. If you dream of a sophisticated and stylish acrylic bathtub, pay attention to the design of bathtubs from Italian manufacturers.

When choosing an acrylic bathtub, decide what space in your bathroom it will occupy; the size of the bathtub depends on this. For a small room, an ergonomic bathtub measuring 120x70 is suitable, and for a more impressive space, you can choose a more impressive size, for example, 190x120.

Tip 3: Pay special attention to quality
When choosing a bathtub, first of all, check the presence of all certificates, and also find out what polymer the bathtub you like is made from. There are two types of polymers that are used to make acrylic bathtubs.
The first - ABS/PMMA - is a combination of two types of polymers - acrylonetrile butadiene styrene and polymethyl methacrylate, combined by co-extrusion, that is, combining materials with different properties. The thickness of the acrylic layer in such baths is only 5-10%, everything else is ABS polymer, which has a number of disadvantages - relatively low density, tendency to absorb moisture, roughness and porosity of the structure. Such baths are usually cheaper, but be prepared for the rapid appearance of microcracks, chips, and loss of appearance. The service life of such baths is only 3 years.

The second type of material is 100% cast homogeneous acrylic, that is, polymethyl methacrylate. Bathtubs made from this polymer have all the qualities necessary for a bathtub - wear resistance, high strength, good appearance, maintainability. The service life of bathtubs made of cast homogeneous acrylic can be 10 years.

How to distinguish a bathtub made of 100% cast homogeneous acrylic from an ABS/PMMA bathtub? Look at the cut edge of the bathtub. If the bathtub is made of homogeneous acrylic, there should be only two layers - acrylic and resin. ABS/PMMA bathtubs have three layers - a thin layer of acrylic, a large layer of ABS plastic and a third layer of reinforcement. So if the cut of the bathtub is more than 8 mm thick, and the seller tells you that the acrylic here is 6-8 mm thick, then most likely you can say that he is lying. There is 1 mm of acrylic as such, followed by a layer of plastic - ABS.

The quality characteristics of an acrylic bathtub that are worth paying attention to also include its rigidity and shape stability. These qualities are given to an acrylic bathtub by the reinforcement procedure that the bathtub undergoes during manufacture. The reinforcing layer consists of fiberglass and epoxy resin. And the reinforcement process, accordingly, is the application of such a layer to the bathtub. The more layers, the stronger the bathtub. The number of layers with which the bathtub was strengthened at the factory can be easily determined by carefully examining the edge of the side. The layers are clearly visible, like annual rings on wood. Therefore, the walls of the bathtub should not sag; this must be checked when choosing a bathtub.

Obviously, the better the quality, the higher the price. A compromise allows you to find bathtubs from Polish manufacturers that offer a very reasonable price-quality ratio.

Tip 4: Tuning your bath
For an acrylic bathtub, you can purchase additional equipment. This includes faucets, a hydromassage system, decorative panels, end/front curtains, headrests, handles, rugs, etc.

Of all of the above, the necessary equipment that will definitely need to be purchased along with the bathtub is a mixer. And here is another advantage of an acrylic bathtub - the mixer can be placed on the side of the bathtub in any place where it is more convenient for you. You can even make several mixers. An acrylic bathtub allows you to realize all your ideas.
Faucets, like all plumbing fixtures, vary in price and quality. When choosing, for example, Italian manufacturers, you can be sure that the money was not paid in vain. Take a cheaper one, made in China - it's up to you, but don't expect a long service life.

Tip 5: Buy a bath without leaving home
Now there are many places where you can buy an acrylic bathtub: plumbing stores and showrooms, construction markets, specialized shopping centers. But all this requires a lot of time, effort and nerves. Recently, it has become possible to purchase acrylic bathtubs online. It is much more convenient and profitable. You can choose the option that suits your price and design, which will be delivered to you directly to the specified address.

OPERATION OF BAS BATHTUBS

Thank you for purchasing a “BAS” brand bathtub. “BAS” hydromassage baths are modern technologies and original lines that provide the comfort of hydromassage, which will improve your health and give you many pleasant moments. This manual describes the bathtubs' functions, installation requirements, care and operating methods.

ATTENTION:

In order for the bath to be beneficial for you, to work for a long time and reliably, a number of conditions must be met:
If your body has problems with the functioning of the cardiovascular system, then consult a doctor (to what extent is hydromassage beneficial for you).
Consider installing filters (for water purification) - this will increase the service life of your faucets and hydromassage bath equipment.
Do not turn on the hydromassage without filling the bathtub with water.

TECHNICAL DESCRIPTION

Standard equipment for a hydromassage bath:
Acrylic bathtub – hydromassage – 1 pc.
Acrylic panel – 1 pc.
Drain and overflow device – 1 pc.
Legs – 3 - 5 pcs. (depending on model).
Panel clamp – 4 pcs.
Self-tapping screws for attaching acrylic panels – 1 or 4 pcs. (depending on model).
TRANSPORTATION OF BATHTUBS

When transporting and installing the bathtub, care must be taken not to damage the piping systems and electrical equipment. DO NOT carry the bath by the pipes and nozzles.
INSTRUCTIONS FOR PREPARING A SITE FOR INSTALLING BATHTUBS:
A plumber performing work on hot and cold water pipes must take into account the linear dimensions of the bathroom. Otherwise, the pipe outlets may rest against the stiffeners, units and fittings of the bathtub. This means that the bathtub cannot be installed close to the walls.
The bathroom drain pipe should not rise above the floor by more than 10 cm. If this cannot be ensured, then a podium must be made.
The legs serve to level the bathtub, so additional supports must be installed under the supporting structure of the bathtub.
Electrical wiring must have multiple insulation access to exposed contacts, at least 3 mm thick. System protection must be based on differential (multiple) shutdown (1 fn =30 mA). The supply cable must comply with EEC standards or be type H07 RN-F, according to VDE 0250. Near the bathtub and in a place protected from water (recommended minimum height from the floor 25 cm), a socket should be installed with (make sure that the grounding cable is correctly installed). The baths are delivered ready to be connected to the electrical network. Do not under any circumstances swap installed terminals.

ELECTRICAL SYSTEM

The installation of the electrical system must be carried out by a professional electrician. must have a differential switch 3 0mA, magnetothermo 2.4 - 4A, and another common connection (CEI 64-8). If it does not exist, install one in the apartment’s common panel.

DO NOT INSTALL UNDER THE BATH.

The procedure for connecting hydromassage baths to the electrical network:
Yellow-green wire - grounding;
Brown wire - phase;
Blue wire - 0.
V
220 / 240 Hz
50 W
0.7 – 0,9
depending on the bath model

HYDROMASSAGE EQUIPMENT

BATH CARE

For daily cleaning of the bathtub, use a liquid cleaner and a soft cloth. To maintain the shine of the bathtub, you can wipe it with a cloth with a polishing agent. Stubborn stains in the bathtub can be removed using conventional household cleaning products for smooth surfaces. To clean the bathtub, use only soft cloth napkins.

Deposits on the surface in the form of scale are removed with a soft cloth moistened with lemon juice or wine vinegar.

Scratches or burn marks from cigarettes that appear on the surface can be removed by lightly sanding with fine-grained sandpaper (No. 1000/2000) and water. You can restore the shine of the surface with a liquid polish.
CLEANING THE BATH HYDRAULIC SYSTEM

This type of cleaning is performed using hard water (over 15 salt deposits per cubic meter of water). It is recommended to clean the bathtub hydraulic system twice a year as follows:
Fill the bath with hot water (40 C).
Pour in liquid detergent at the rate of 2 g per 1 liter of water and run the hydromassage unit for about 5 minutes.
After this, turn off the electric pump and drain the water from the bath.
Fill the bathtub with cold water again and turn on the hydromassage for 2 minutes.
Drain the water and wash the bathtub (see “Washing the bathtub”).

IMPORTANT NOTE

WARNING: Never use metal brushes or tools, or use solvents or detergents containing abrasives to remove dirt from the surface of the spa. Also avoid contact of ammonia or chlorine with brass and chrome parts of the bathtub.

HOW TO USE HYDROMASSAGE BATHS

Never turn on the hot tub until the water reaches 5-6 cm above the jet opening. Never use the bathroom after taking alcohol or taking medications. Hydromassage for medicinal purposes can only be performed on the advice of a doctor, who will select the appropriate duration of sessions and water temperature for you.

Taking a cold bath improves your health. A warm or slightly hot bath relieves tension. To relax muscles and relieve pain, take a bath (up to 40 C). The first hydromassage session, which should be carried out only in warm water, should last no more than 10 minutes. The effect of water jet massage is directly proportional to the temperature of the water and the duration of the session. After taking a bath for too long, you may feel tired. And if you feel sleepy while taking a bath, turn off the hydromassage device for a while and cool the water.

For overweight people, hydromassage baths at water temperatures exceeding 38 C are contraindicated.

Before turning on the whirlpool system, make sure that the jet nozzles are not pointing upward.
SIMPLE MALFUNCTIONS, THEIR POSSIBLE CAUSES AND REMEDIES

Processed

OPERATION OF BAS BATHTUBS

Thank you for purchasing a BAS brand bathtub. “BAS” hydromassage baths are modern technologies and original lines that provide the comfort of hydromassage, which will improve your health and give you many pleasant moments.

This manual describes the bathtubs' functions, installation requirements, care and operating methods.

PRECAUTIONS

In order for the bath to benefit you and work reliably and for a long time, a number of conditions must be met:

1. If your body has problems with the functioning of the cardiovascular system, then consult a doctor (to what extent is hydromassage beneficial for you).

2. Consider installing filters (for water purification) - this will increase the service life of your faucets and hydromassage bath equipment.

3. Do not turn on the hydromassage without filling the bathtub with water.

4. Do not allow the bathtub to be walled up in tiles, panels or hard mortars, restricting access to hydromassage equipment that prevents the bathtub from extending to a distance of at least 0.5 m from the wall.

5. The bath is connected to a single-phase alternating current network with a voltage of 220V. To avoid electric shock, the bathtub must be grounded through an outlet with a grounding pin connected.

TECHNICAL DESCRIPTION AND EQUIPMENT

The standard configuration of bathtubs is shown in the following table

Equipment List A-for bathtubs models “CAMERON”, “LIMA”, “TESSA”, “VERONA”, “IBIZA”, “BREEZE”, “ALEGRA”, “VECTRA”, “MALDIVE”, “STYLE”, “SAGRA”, “ATLANTA” ", "NEPTUNE", "MALTA", "AKHIN", "FLORIDA", "FANTASY";

Equipment list B-for bathtubs of the “INDICA”, “JAMAICA”, “LAGUNA” models;
Equipment list C-for bathtubs of “CAPRI” models;

Equipment list D-for bathtubs of “FIESTA” models;

Equipment list E-for bathtubs of “NIKOL” models;

Equipment list F-for bathtubs of the “RIOLA”, “XATIVA”, “IRIS”, “IMPERIAL”, “MEGA”, “DROVA” models;

Equipment list G-for bathtubs of “RIVIERA” models;

Additional equipment includes: hydromassage, back massage, Shiatsu massage, aeromassage, lighting, chromotherapy, control panel, mortise mixers and handles.

Depending on the bathtub model, the manufacturer provides panels (screens) for bathtubs (front, side), shower curtains and headrests, which are not additional equipment and are not included in the kit. The manufacturing company reserves the right to make changes to the design and configuration of the bathtubs.

TRANSPORTATION OF BATHTUBS

The bathtub must be transported only in a horizontal position. When transporting and installing the bathtub, care must be taken not to damage the piping systems and electrical equipment. The bath should be moved only for the body or frame. It is necessary to avoid mechanical damage to the bath body and panel, and also to exclude the possibility of exposure to chemically active reagents on the surface of the product. When transporting in the cold season, before installation, the bath must be kept at room temperature for at least 6 hours.

ATTENTION! It is strictly forbidden to move the bathtub by pipelines, nozzles, handles and other equipment! Inspect the product for compliance with the order, absence of mechanical damage, completeness, availability of accompanying and warranty documentation.

REQUIREMENTS FOR THE BATH INSTALLATION LOCATION

The room in which the bath is installed must meet the following requirements:

Tiling and finishing work must be completed;

It must be possible to easily access the components and assemblies of the bathtub for its preventive warranty maintenance and repair;

Availability of a power line with the required parameters and a socket with a connected grounding contact. The power supply to the bathtub connection point must be provided by a double-insulated electrical cable with a cross-section of at least 2.5 mm2 and is in accordance with the norms and standards of the EEC;

Availability of water supply and sewerage. The bathroom sewer pipe should not rise above the floor at the connection point by more than 10 cm. If this is not possible, then it is necessary to provide a podium under the bathtub;

REQUIREMENTS FOR INSTALLING A BATH

Installation of the bathtub should be carried out only by qualified specialists, in compliance with the following requirements:

Installation of a bathtub without a frame, as well as with a modified frame, is not allowed. The legs are used to level the bathtub and adjust the gap between the bathtub panel and the floor. The bathtub must rest on all support points to prevent uneven distribution of the load and, as a result, the appearance of microcracks in the bathtub body;

It is not allowed to embed the bathtub in tiles, panels or hard mortars. To avoid moisture getting under the bathtub or on the hydromassage equipment, the seams between the bathtub and the wall must be sealed with plumbing silicone.

Avoid getting dirt and construction dust on the surface of the bathtub. This can cause clogging and failure of the hydromassage equipment or lead to scratches on the surface of the bathtub during subsequent unprofessional cleaning.

When carrying out work on the removal of water supply and sewerage pipes, it is necessary to take into account the linear dimensions of the bathtub. Otherwise, the connection may be difficult, since the pipe outlets may rest against the stiffeners, units and fittings of the bathtub, and the bathtub cannot be installed close to the walls. Structural changes in the arrangement of equipment and pipelines of the bath, cutting of mounting clamps, and so on are strictly prohibited.

The electrical wiring of the room must have an individual differential switch 30mA, magnetothermo 2.4-4A or another common connection (CEI-64-8) and installed in the common switchboard of the room. It is strictly forbidden to install this switch under the bathtub!

ATTENTION! Failure to comply or not to fully comply with the above requirements does not provide for the preservation of warranty conditions for service or repair for such a bathtub.

BATH INSTALLATION

Install the bathtub on the legs (Fig. 1). The manufacturing company allows the legs to be equipped with an M12 bolt, instead of the corresponding threaded rods. Feet configuration A(Fig. 1) (2 pcs.) - installed on the front (front) side of the bathtub, along the edges, on the left and on the right (for a bathtub " RIVIERA" - 4 pcs., all at the front). Feet configuration B(Fig. 1) - other remaining front and rear legs. The legs are connected to the frame using the upper pair of M12 nuts, which also serve to adjust the height of the bathtub.

Install a drain-overflow device on the bathtub (Fig. 2), a siphon (may not be included in the kit), and adjust the bathtub in height. The distance from the floor level to the bottom point of the siphon must be at least 15 mm. Make sure that the bathtub is adjusted and rests on all points of support.

Install the panel onto the bathtub by snapping it onto the upper fasteners (Fig. 6 and 7). On some models of symmetrical and asymmetrical “BAS” bathtubs, it is possible to trim the panels to length (no more than 2 cm per side). In addition, if you plan to install a side panel on your bathtub, then first install the top fasteners under it that come with the side panel. Adjust the verticality of the panel. The bottom of the panel should be adjacent to the plane of the corner corner installed on the outer legs. The seating depth of the angle is adjusted by the lower pair of M12 nuts. The corners should be equally adjusted in height and be symmetrical relative to the panel.

Using a drill with a diameter of 3.5 mm (the size indicated for a self-tapping screw is 4.2x25 mm), drill through holes in the lower corners and panels (Fig. 4 and 5).

Remove the panel from the bathtub and connect it to the sewerage and water supply systems (see Connecting the bathtub to the water supply and sewerage network), as well as to the 220 V electrical network (see Connecting the bathtub to the electrical network). After this, carefully move the bathtub tightly against the wall, and once again make sure that it is stable at all points of support, and all connections are made correctly.

6. Install the panel on the bathtub and fix its bottom into the drilled holes with a self-tapping screw and a press washer (Fig. 8).

7. Close the head of the screw with a decorative plug (Fig. 9).

ATTENTION! TO AVOID MOISTURE GETTING BEHIND THE BATH, MUST TREAT THE SEAM WITH PLUMBING SILICONE AROUND THE ENTIRE PERIMETER OF THE BATH!

CONNECTING THE BATHROOM TO THE WATER SUPPLY AND SEWERAGE NETWORK

The connection of the bathtub to the water supply and sewerage network must be carried out by a qualified plumber.

The bathtub kit includes a semi-automatic drainage device, which, after installing it on the bathtub, is permanently connected to the sewer network through a flexible corrugated or rigid PVC pipe (not included in the kit). A sewer drain with a diameter of 40-50 mm is installed at the bathtub installation site in the floor or wall, taking into account the linear dimensions of the bathtub. When the drain pipe is located in the wall, the optimal height is considered to be no more than 2 cm from the floor level to the bottom edge of the pipe.

Connecting the bathtub to the water supply network if it is equipped with a mortise mixer. The network pressure should be 3-5 atm. At pressures above 5 atm, pressure reducers should be installed and adjusted to the specified standards.

Places for connection to the water supply system must be placed taking into account the linear dimensions of the bathtub and its units and equipped with taps disconnecting from the main line. Connection to the system is made through a flexible plumbing connection (water hoses). The length of the hoses must allow the bath to be moved from the walls and a distance of at least 0.5 m. Recommended use of water purification filters. The absence of filters can lead to clogging of hydromassage nozzles and metal scale entering the ceramic mixer cartridge, which will lead to their failure.

ATTENTION! Inset mixers are equipped with a set of standard flexible hoses. If the length of the flexible line is not enough for connection to the system or connection between the elements of the mixer, then it is purchased separately, taking into account your dimensions for connection. The bathtub manufacturer is not responsible for the nature of the set of mortise mixers, for damage to the elements of the hydromassage system caused by their contamination when using unfiltered water containing rust, sand, chemically active impurities, as well as for breakdowns or incorrect operation of the bathtub equipment connected to the system water supply with non-standard pressure in it.

Leave the bathtub unattended when filling it with water. Overfilling the bathtub with water can lead to failure of the air massage system, without maintaining the warranty conditions for the product.

Rotate the drain-overflow cover around its axis or while placing a weight on the bathtub plug.

CONNECTING THE BATH TO THE ELECTRICAL NETWORK

The electrical equipment of the bath is powered from a single-phase alternating current network, in accordance with the table below.

*power is indicated depending on the bath model

Connecting the bath to the electrical network must be carried out by a qualified specialist with clearance group 3 or higher. The procedure for connecting hydromassage baths to the network:

The yellow-green wire is “grounding”;

Brown wire - “phase”;

Blue wire - “zero”;

The bath's power supply must be connected only through a separate residual current device (RCD), rated 30 mA and located outside the bathroom.

A detachable type of connection of the bath to a 220 V network is allowed. Depending on the configuration of the bath, elements of hydromassage equipment may not be equipped with electrical plugs for connection. In this case, they are purchased separately and installed independently. Each piece of equipment intended to be connected to the network must have an individual connection to the electrical network.

Connect units together, into one plug, etc.

Use the bathtub with a socket or plug without a working grounding contact.

Ground the bath through heating, plumbing and sewerage equipment.

Operating the bathtub with a damaged electrical cord or with a faulty or unconnected ground.

Carry out technical work with the bathtub plugged in.

HYDROMASSAGE AND ADDITIONAL EQUIPMENT

The following elements of hydromassage equipment can be located on the bathtub (see View A):

Email Hydromassage motor with hydraulic pump

Air massage compressor

Bathroom control buttons and controls

hydromassage jets (reverse side)

piping system

Additionally, they can be installed on the bathtub

air massage (installed in the bottom of the bath, see Fig. 1)

Inset mixer (see Fig. 2)

Back massage (see figure 3)

Shiatsu massage (back massage or back massage + foot massage) (see Fig. 4)

Chromotherapy (see Figure 5)

Backlight (see Figure 6)

Headrests (see Figure 8)

BATHROOM CONTROL

The bath functions are controlled using the following equipment:

A) Hydromassage jets.

Provide adjustment of the direction and strength of hydromassage jets. The direction of the jet can be easily changed by turning the nozzle nozzle within a 30-degree angle. The force of the water jet is regulated by rotating the nozzle nozzle around its axis. The maximum jet flow is achieved by fully opening the jet nozzle counterclockwise (open nozzle).

B) On/off button Hydromassage functions with air supply regulator (ARS). Provides on/off. hydromassage system by pressing in the center. The RPV dispenses the amount of air mixed with the stream of water during operation of the hydromassage system, due to the injection process. By turning the knob you can change the amount of air flowing along with the stream of water from the hydromassage nozzles. The power of the jet increases with the supply of air into it.

IN) On/off button Aeromassage functions (chromotherapy lighting). Provides on/off switching of the air massage system. When turned on, the compressor pumps air under pressure through air nozzles installed at the bottom of the bath. At the same time, small air bubbles burst to the surface, massage and enrich the skin with oxygen. Can be used to turn on/off. Chromotherapy lights.

G) Crane balance (turbopool).

Switches the operating modes of the hydromassage system between the general hydromassage function and the back massage function (Shiatsu massage). Adjust the desired distribution of water supply using the indicated functions by turning the “flag” of the switch.

D) Electronic remote control for bath functions (No. 2).

Buttons for adjusting the power of the air massage function

On/off button air massage functions

On/off button Chromotherapy (backlight) functions

On/off button Hydromassage functions

E) Electronic (touch) remote control for bath functions (No. 3).

Remote control power on/off button

Button to turn on/off the hydromassage function

Button to turn on/off the backlight/chromotherapy function

Multifunctional button for switching operating modes: radio station frequency ( MHz) / radio station channel number ( ch) / radio station frequency setting mode (flashing sign TUNE) / volume control mode ( d) / air massage power level adjustment mode (number from 1-10 ). Also used as a selection confirmation button when recording radio channels into memory. Up to 10 configured channels can be stored in memory ( CH).

Buttons for setting modes: volume level / radio station frequency / radio station channel number / air massage power level. The setting is carried out depending on the mode selected by button 5 ( SET).

Radio on/off button.

Button to turn on/off the air massage function.

ATTENTION! If your bathtub is equipped with a control panel, then when the water level in the bathtub is lower than required, all functions are turned off, except for the radio and air massage.

HOW TO USE HYDROMASSAGE BATHS

ATTENTION! Never turn on the hot tub until the water reaches a level 5-6 cm above the main whirlpool jet opening. Avoid high thermal effects (above 65 degrees Celsius) on the surface of the product - this can lead to its damage! It is prohibited to turn on the hydromassage function when the jet nozzles are closed. Before turning on the hydromassage system, make sure that the jet nozzles are not directed upwards and that the balance valve is not in the back massage position (Shiatsu massage). During operation of the hydromassage, it is forbidden to block the grille of the water intake valve, preventing the flow of water into it. After using the bath and draining the water, it is recommended to blow out the air massage jets by turning on the air massage function for 1 minute.

Never use the bathroom after taking alcohol or taking medications. Hydromassage for medicinal purposes can only be performed on the advice of a doctor, who will select the appropriate duration of sessions and water temperature for you.

Taking a cold bath improves your health; taking a warm or slightly hot bath relieves stress. To relax muscles and relieve pain, take a bath at 40 degrees Celsius. The first hydromassage session, which should be carried out only in warm water, should last no more than 10 minutes

The effect of water jet massage is directly proportional to the temperature of the water and the duration of the session. After taking a bath for too long, you may feel tired. And if you feel drowsy while taking a bath, turn off the hydromassage device for a while and cool the water.

Overweight people should not use hot tubs at water temperatures exceeding 38 degrees Celsius.

BATH CARE

For daily bath cleaning, use a liquid cleaner that is harmless to acrylic and plastic surfaces (see cleaning product instructions) and a soft cloth. The manufacturing company offers you a specialized cleaning agent “TIM-PROFI”, adapted to our products. To maintain the shine of the bathtub, it can be wiped with a cloth with a polishing agent. To clean the bathtub, use only soft cloth napkins.

Deposits on the surface in the form of scale are removed with a soft cloth moistened with lemon juice or wine vinegar.

Scratches or burn marks from cigarettes that appear on the surface can be removed by lightly sanding with fine-grained sandpaper (No. 1000/2000) and water. You can restore the shine of the surface with a liquid polish.

ATTENTION! To remove dirt from the surface of the hot tub, never use metal brushes or tools, or use solvents or detergents containing abrasives. Also avoid contact of ammonia or chlorine with brass and chrome parts.

CLEANING THE BATH HYDRAULIC SYSTEM

This type of cleaning uses hard water (over 15 salt deposits per 1 cubic meter of water). In addition, it is recommended to clean the bathtub hydraulic system Twice a year in the following way:

Fill the bath with hot water (40 degrees Celsius).

Pour in liquid detergent at the rate of 2g per 1 liter of water and run the hydromassage system for about 5 minutes.

After this, turn off the hydraulic pump and drain the water from the bath.

Fill the bathtub with cold water again and turn on the hydromassage for 2 minutes.

Drain the water and wash the bathtub (see “Bathtub Care”).

SIMPLE MALFUNCTIONS, CAUSES AND METHODS OF THEIR ELIMINATION

First of all, of course, a few words should be said about the company that produces acrylic bathtubs BAS. This company continues to surprise its consumers and partners, proving that bathtubs produced in Russia are no worse than their foreign counterparts.

The main products of this company are hydro and air massage acrylic bathtubs. Among the obvious positive aspects of acrylic bathtubs produced by BAS are the following:

• acrylic bathtubs from bas are manufactured using multilayer polymer plastic from the company senoplast - the combination of acrylic and ABS plastic gives the bathtub strength and reliability;
• the same plastic from senoplast also has an antibacterial effect, which protects the bathtub from the proliferation of various bacteria
• Bathtubs from bas are manufactured using high-quality Italian equipment, so the products can compete with European products
• acrylic bathtubs are reinforced with a steel frame, which is well protected from water
• the products are manufactured in Russia and therefore their features take into account the design of Russian bathrooms

Buyers about BAS bathtubs

I wonder what the buyers themselves say about acrylic bathtubs; reviews are quite easy to find on the Internet. It turns out that the majority of customers were very satisfied, saying that the acrylic bathtub from bas works great. Buyers happily share their impressions that the bathtub of this company:

• does not scratch, despite the fact that the shower periodically falls into it
• The side is very thick and you can sit on it
• the bath retains heat well, and therefore you can bathe in it for a long time, even if there is limited hot water
• The bathtub is equipped with excellent comfortable armrests
• takes up little space, all models are well thought out
• the only part that earned several negative reviews was the hydro and air massage system - they say that it does not last very long, and repairs are quite expensive

Another interesting point was that many buyers installed and assembled both an acrylic bathtub and a bathroom curtain on their own. Of course, not everyone can do this, but we can still assume that this indicates the quality of the product, since even an unprofessional assembler will do everything efficiently. However, the installation of an acrylic bathtub bas can be done by professionals - it all depends on the client’s capabilities. The instructions that come with the bathtub are quite clear and simple, so assembling the bas acrylic bathtub is not difficult.

Three great examples of BAS products: Atlanta, Florida and Laguna

One great example is the acrylic bathtub bas atlanta, which has certain advantages. So, the dimensions of this bathtub model are quite modest, it is suitable even for a small bathroom - 170 by 70 cm. However, the capacity is very good - 205 liters. Since BAS baths are mainly hydromassage, Atlanta is no exception - it is equipped with six nozzles - three on each side.

The required kit includes a standard set:

• metal frame that guarantees the strength of the bath
• legs under the bathtub, which allow you to adjust the height of the bathtub and ensure its stability
• a front panel that will cover the space under the bathroom and give the interior a complete look
• necessary device for draining and overflowing

In terms of design and space optimization, this is a very simple, medium-sized rectangular bathtub that is quite comfortable, but does not take up too much space or distract too much attention, so it will easily fit into almost any modern design.

Another example of an excellent bathtub is an acrylic bathtub - this is a corner asymmetrical bathtub. It is quite compact in itself - length 160 cm and width 88 cm, and at the same time it also has a beveled corner, so it will be an ideal option for a small room. Although her style is quite simple and elegant, if desired, you can highlight her - for example, create a visually separate space for her, using decorative elements, finishing with tiles of a different color or shade, additional shelves, etc. In addition to its ergonomic design, this bathtub also has an interesting shelf for hygiene items, or even to sit on.

The equipment here is standard - the same as in Atlanta. The capacity is also 205 liters. But there are more hydromassage jets - there are eight of them.

The last one to consider, of course, is a model such as an acrylic bathtub bas lagoon, which is somewhat similar to the Florida model. However, Laguna is larger in size - 170 by 110 cm. The capacity is also much larger - 295 liters. And the number of hydromassage nozzles is the same - eight pieces. The equipment is standard.

This bathtub is suitable for a medium-sized room, due to the fact that although it is asymmetrical, it is still quite large and is unlikely to fit well in a small room. This model is also very conveniently equipped with a shelf for bathroom accessories and has an ergonomic design. At the same time, it will most likely be one of the main elements in the design of the room, this is facilitated by its rather large size. Therefore, you can highlight it with directional colored lighting or other decorative options. Also, a great idea would be to hang a large mirror next to the bathtub so that it expands the space and the bathtub no longer seems bulky.

In addition to the standard equipment, BAS offers its customers a fairly large selection of additional options. These additional features can be divided into several groups:

1. Aero and hydromassage lotions: various types of massage - back, shiatsu, foot; aeromassage from 6 to 12 nozzles, hydro-aero-pipe massage.
2. Faucets: cascade mixer or even the whole set: spout, mixer, shower holder.
3. Illumination: various types of illumination and chromotherapy.
4. Pleasant little things: headrest, armrests, cleaning products for the massage system or the bath itself, a pillow for the on and off buttons.

The BAS company provides its customers with really wide possibilities in choosing a model and a set of bathtub configurations, plus you can choose a design curtain.