Unique DIY infinity table. How to make a table with lighting: ideas, materials, step-by-step instructions, photos and videos Mirror table with infinity effect

Table with lighting - very interesting and eye-catching element decor rooms.

Thanks to the use of a translucent mirror and multiple sources light is created amazing Effect shining tunnel.

This unusual piece of furniture is also called an infinity table, 3D table And glowing table.

LED strips

When making a table it is used LED Strip Light, which creates the effect of infinity.
The most convenient are self-adhesive tapes.

Operating principle

The LED strip consists of two diodes - single-chip, having one color spectrum, and three-crystal, consisting of three color spectra (green, blue, red).

Radiation crystals mix to form a wide range of colors gamma

Specifications

1. LED type - The main difference between all LED strips is from each other. The most common are SMD LEDs 3028 and SMD 5050.
   The abbreviation stands for “surface-mounted device”, and the numbers indicate the dimensions of the LED lamps: 3.0 x 2.8 mm and 5.0 x 5.0 mm.
2. Density. The more LEDs per one linear meter, the brighter the glow from the tape.
3. Glow color LEDs can be anything. The most popular are white, yellow colors, cold and warm tones.
4. Moisture protection. IP 20 - open, IP 65 - moisture resistant, IP 68 - highest degree moisture protection.

Advantages

• Large light recoil;
• High strength and vibration resistance of tapes;
• Long operational life (about 100 thousand hours);
• Various tones and shades glow of lamps;
• Inertia the tapes are small, which allows you to use the most high brightness from the very moment you turn it on;
• Quantity cycles turning on/off does not in any way affect the service life of LED strips;
• Environmental friendliness;
• Safety;
• Budget price;
• Not susceptible to breakage due to low temperatures temperatures

Note! High temperatures are strictly contraindicated for LED strips.

How to make a backlight computer desk with help LED strip, look in video:

DIY 3D table

Let's consider making more complex, but the safest and beautiful LED table.

Materials

In order to make a table, you will need the following materials:

• Mirror(diameter 60 cm);
• Mirror translucent self-adhesive film;
• Expanded polystyrene(for the body);
• Glass or plexiglass (thickness 4 mm, 65 x 65 cm);
• Metal strip on a roll (for windows);
• Wires;
• Instantaneous Super glue;
• Bilateral scotch;
• power unit 5/5.5V 200/300mA s USB output;
• Self-adhesive tape LED(not less than 1.5 - 2 meters);
• Arduino Uno;
• Programmer for Arduino (for projects);
• USB for powering the microcontroller.

Note! The mirror can be of absolutely any shape: square, circle, oval, D-shaped bar counter, etc.

Tools

Tools, necessary to create an LED table:

• milling cutter(a nozzle is required for making round parts);
• regular or
• soldering iron(you definitely need solder for a soldering iron);
• Dremel;
• scissors;
• knife(for cutting metal and plexiglass);
• pencil, pen, thin marker;
• square(ruler).

Stages of work

Step 1. Cut from a piece of plexiglass circle according to the diameter of our mirror. The edges we clean up we remove the shavings.

Note! When cutting a circle from plexiglass, you should move the milling machine quickly so that the edge does not melt.

Step 2. Carefully glue the self-adhesive tape onto the plexiglass. film. We glue the plexiglass to the table with tape. We remove the film that is applied to plexiglass, and film from mirror film. Spraying plexiglass water, and even better - soapy solution. We place the mirror film on the glass and expel all the formed bubbles.


Step 3. Protruding edges of the mirror film cut off scissors. We leave the entire structure to dry (at least 12 hours).

Step 4. Carefully attach to the dried mirror plexiglass metal strip using transparent superglue.


Step 5. We glue the LED strip on internal side of the metal strip.

Step 6. We drill holes in the metal strip for wires


Step 7 We polish the received holes.

Step 8 The connection code can be write yourself, or you can use a ready-made one. Scheme connecting the Arduino Uno controller:


Step 9 From plexiglass you need to cut 10 - 15 small rectangles. Using clear instant adhesive, attach them to facial side of the mirror. They will serve as supports for designs made of glass and metal. Size The rectangles should be such that the strip together with the plexiglass overlaps our mirror.


Step 10 To rectangles install top structure with glass. The glue must be completely dry out. It is advisable to put something heavy on top for the best bonding surfaces.

Step 11 Second (external) film remove from the plexiglass. This design can be used as mirror. We install the structure on a table with a tabletop of the same or smaller diameter

Step 12 We supply food to Arduino and download our code.

• Not worth it undertake for making a glowing table, if you are not sure what Right connect the LED strip to the battery or network. Incorrect or careless may result in short closure and fire.
• Films that protect glass from external influences, filming in the end - that's how it is will save mine appearance.
• Before cutting plexiglass in the middle of the circle two-way We attach a piece of wood with tape bar. It will serve as a support for the router.
• Glue must be taken waterproof.
• Glue LED strip needs a good, strong double-sided scotch. If the tape comes off when the table is completely ready, have to open the entire structure for corrections this problem.
• Minicontroller put it in a box and attach it to below countertops.

For nutrition tapes can be used Electricity of the net or build a small battery. When powered by a battery, the table will become even more safe and will not depend on the power grid. It can also be installed in suburban home where there is no power supply.

LED strips are safe and durable. To illuminate the table you can use plain or multi-colored LED strip (they differ only in price). Luminous the table will delight the owners and their guests with an unusual design.

How to install lamps to illuminate the desktop in the kitchen, see the following video:

In contact with

See inaccuracies, incomplete or incorrect information? Do you know how to make an article better?

Would you like to suggest photos on the topic for publication?

Please help us make the site better! Leave a message and your contacts in the comments - we will contact you and together we will make the publication better!

Every owner wants to add a touch of originality to their interior. And everyone has their own methods for this. Some people come up with original design rooms, thanks various forms ceiling and walls, while others opt for One of these interior items that will catch the admiring glances of your guests will be a table with an infinity effect.

What is the secret?

The infinity effect is achieved through the use of LED technology. They are the ones who can decorate your home, and in some cases even change it beyond recognition. A table with an infinity effect, the photo of which is presented in this article, is a modern, innovative piece of furniture that can change the idea of ​​design of even the most notorious skeptic.

The secret of visual infinity is hidden in the use of LED backlighting, and color solutions there can be a huge variety. It is this that is built into the space between the reflective surfaces. As a rule, the top mirror is translucent so that the radiation from the LEDs is visible to others.

To control the backlight, use a special remote control or, if you made a table with an infinity effect yourself, an on/off button.

Where can the table be used?

The use of tapes with is absolutely safe for human health and environment, so the infinity table can be positioned anywhere. In addition, such lamps are famous for their durability and efficiency. A product with a tunnel effect will serve you for quite a long time, thanks to its reliability and ease of use. This table can be seen in:

• modern apartment;
• country house;
• nightclub, bar or restaurant;
• hotel;
• office.

How to make an infinity table yourself

The price for such a piece of furniture is not encouraging, and the purchase is not always affordable for the average resident of the country. However, you can get an unusual thing if you know how to use tools. Just make a lighted table yourself.

For this you will need following materials and tools:

• boards for the table;
• mirror and glass (the latter can be replaced with a translucent mirror);
• LED Strip Light;
• self-tapping screws;
• screwdriver

All wires are mounted in the table legs.

First of all, you need to develop a drawing, taking into account all the dimensions of the future piece of furniture. From MDF (or wooden boards), mirrors need to be made according to your calculations. There should be 3 wooden templates with an internal hole, one of which has a larger internal diameter by approximately 1 cm. This is where the LED strip will be located. The resulting blanks need to be glued together, not forgetting to insert one mirror between the two lower templates. Then you need to carefully smooth all sides and corners.

Next you need to attach the cover. It would be better if it was removable. This will provide access to electricity. This cover for the future table can be decorated to suit your interior. You can paint it or decorate it in any other way.

In the opening of the table cover it is necessary to drill holes that are necessary for attaching the LEDs. Now you can insert the tape into this opening and secure it in a way convenient for you. The best option would be to use glue, the effectiveness of which you will be 100% sure of.

Now you should cover it all with a second mirror, translucent.

All wires are routed through the table legs. To do this, they must have a wide cross-section and through holes.

As a conclusion

To enhance the effect or make it more original, you can put absolutely any object between two mirrors. This is done to ensure that the infinity table fits perfectly into the overall concept of your room.

In addition, you can safely combine LEDs of different shades. Connecting pieces of tape is not difficult even for an inexperienced craftsman.

A similar effect can be used not only to make a table, but also to decorate doors or any other surfaces. A table with an infinity effect, made with your own hands, can be just the beginning.

There are many creative ideas, used furniture craftsmen when making masterpieces with your own hands. A bright, original and memorable product that will perfectly decorate modern interior and will create a unique atmosphere is a coffee table with an infinity effect. Making it is not very easy, but it is quite possible if you have some skills in working with wood and glass.

You can place a table with lighting in either office space either at the dacha or at home. LED bulbs, used in the assembly of such furniture are absolutely safe for human health, as well as for the environment. Such lamps are durable and economical, so using a table with an infinity effect will not lead to increased energy consumption.

The illusion of an endless tunnel is created by using two mirror surfaces and LEDs located between them. The colors of the lamps used can be any, but experts say that red diodes can make the tunnel deeper, since red color is less prone to scattering than other colors.

To control the backlight, the on/off button or a special remote control can be used.

Preparing to start work

To make a coffee table with a mirror, you need to prepare the necessary tools and materials. The master will need:

• boards - wood or chipboard;
• sandpaper - it is needed for processing the boards after cutting them (if the material is purchased cut into suitable elements, then there is no need to use sandpaper);
• ordinary mirror - for coffee table diameter about 60-70 cm;
• translucent mirror - its width should be approximately 10 cm larger than the width of a regular mirror ( extra size needed so that the glass can be glued to the strips with LEDs); in the absence of a translucent mirror, you can use glass on which a mirror film is glued;
• power supply with USB output;
• self-adhesive LED strip no less than 1.5–2 m long;
• wires;
• USB for powering the microcontroller;
• microcontroller and programmer for it;
• self-tapping screws;
• Super glue;
• screwdriver

Some craftsmen prefer to make a table with their own hands using a New Year's garland instead of an LED strip. In this case, there is no need to purchase equipment that is equipped with designs with LED strips (microcontroller, USB).

Tabletop assembly procedure

First, a frame (sidewall) is assembled from 4 boards using self-tapping screws. future design, then this frame is glued on top of the mirror, on its front side. In this case, the size of the frame must correspond to the dimensions of the mirror.

At the next stage, you assemble the frame with LEDs yourself. The outer diameter of the frame can be equal to or greater than the outer diameter of the frame, but the inner diameter should be 1-2 cm less than the inner diameter of the frame on each side. When the frame is ready, an LED strip is attached to its bottom side along the inner edge. The frame is then attached to the sides with screws. Holes are drilled in the frame through which the wires are routed out.

When all this work is completed, all that remains is to attach the translucent mirror to the frame. It is screwed with special screws. It is advisable to choose screws that can be removed without much difficulty (in case the LEDs need to be replaced). Craftsmen recommend attaching small strips to the edges of the frame, which in height form a single plane with the glass. At the final stage of work, it will be possible to attach an upper frame to these planks, ensuring reliable fixation of the tabletop.

Not every craftsman can equip a table with such a mirror, because this material is quite rare. Many furniture makers use plexiglass and self-adhesive mirror film, which is applied to the bottom surface of the glass (the one that will be facing the mirror).

Mirror-coated glass is also popular, but it needs to be chosen correctly. You can determine whether mirror-coated glass is suitable for making a coffee table with an infinity effect as follows: you should place a piece of mirror and a piece of glass in parallel, and place any light source between them and visually evaluate the effect.

Another affordable option, which is often preferred by novice craftsmen, is the use of ordinary window glass. But in this case it will not be possible to achieve a sufficient depth of the endless tunnel. In addition, the observer will be able to see everything inside the table.

One of the most important characteristics What you need to pay attention to when assembling a table from mirrors is the depth of the tunnel. It is determined by two factors:

• the distance between the mirrors (the actual distance should be multiplied by 16 to get the approximate apparent depth of the tunnel; in most cases, the actual distance from the bottom mirror to the top is 75-80 mm);
• throughput translucent material.

To ensure long-term operation of the backlight and save energy, it is recommended to use a power supply with a 50% power reserve.

There is an easier way to make your own table with an infinity effect. In this case, instead of an LED strip, a regular one is used New Year's garland. First, a square or rectangular frame is made from bars, then the number of light bulbs on the garland is counted.

After this, marks are placed on the frame in the places where the light bulbs will be located. It is recommended to place them at a distance of about 2 cm from each other. At the next stage of work, holes for light bulbs are drilled in the frame of the future table.

Then light bulbs are inserted into these holes and secured there. Then you need to glue the frame onto the mirror with your own hands, and glue glass with glass on top of the frame. mirror film.

When the backlit tabletop is ready, all that remains is to make the base and legs of the table. The legs should be thick enough (about 10 cm in diameter) so that a hole can be drilled inside one of them for the wires. Exiting the wires through the leg is a solution that allows you to make the product as aesthetically pleasing as possible. You can route the wires directly from the tabletop, but this will make the table less beautiful and convenient to use.

When the legs are made, you need to form a through hole in one of them with a diameter of about 5 cm. In the upper part of the leg, you should make two grooves through which the wires will pass, and also cut out a corner hole necessary for fixing the tabletop.

The height of the hole should be equal to the height of the table top. The depth of the hole must be calculated individually in each case; it must ensure reliable fixation of the tabletop. Similar corner holes are made on all four legs.

In addition to the legs, you need to prepare the base in which the tabletop will be placed. The width of the base should be such that the base protrudes 8-10 cm on each side of the tabletop placed inside it. Free space around the tabletop is needed to accommodate wires and related equipment.

A hole is formed in each corner of the tabletop into which a leg is inserted. Then an outer frame is attached to the base using self-tapping screws, the height of which is equal to the height of the tabletop. Then the legs are screwed on and finished design tabletop fits. The spaces between the table top and the outer frame house wires that are routed out through the table leg.

When the assembly of the base and tabletop is completed, all that remains is to close the space with the wires and additionally fix the tabletop inside the base. A special frame is made for this.

The width of each side of the frame is calculated as follows: the width of the trench with wires + the thickness of the outer frame + a few centimeters to ensure the frame fixes the tabletop. This frame is assembled from four blanks and fastened with self-tapping screws. It is then bolted to the outer frame as well as to the LED tabletop frame.

The holes for the bolts must be drilled in advance to avoid delamination of the wood. The design is ready!

Leave a message!

I'll make it custom-made table with infinity effect according to your sizes. From order to finished product no more than 21 days. Delivery to all regions of Russia by the best transport companies with 100% insurance.

div > .uk-panel", row:true)" data-uk-grid-margin="">

Advantages of ordering a table with an infinity mirror from us

Infinity table- this is one of the main design directions of the Sofia-Led company. Our specialists put their whole soul into the creation of each piece, which is made by hand. No conveyors or production lines during assembly. Individual approach for each product. The principle of such a table is very simple, everyone has known about it for a long time, and its “composition” also does not stand out as anything that could not be bought in a nearby store. But there is one “but” - you need to assemble this “constructor” correctly. Only collected in in the necessary order, With correct sizes and distances, an ordinary table will turn into a table with an infinity effect.

Our tables are made using modern equipment And latest technologies. The finished table does not look like a handmade item. This is facilitated by vast experience in assembling similar products, as well as the availability of all the necessary modern tools.

It is not a shame to give our table with an infinity mirror to colleagues, friends or relatives for a holiday. Do you often host guests and want to amaze them with something unusual? Brew tea and seat your guests at our table, and the infinity tunnel with dynamic lighting will capture their gaze for a long time. Let's now take a closer look at the benefits of our infinity mirror tables:

• Ability to use absolutely any table. Thanks to the availability necessary equipment and vast experience we can put the infinity effect on any table. It doesn’t matter either the thickness or its dimensions.
• Only quality materials . We use time-tested materials and components - from glass and mirrors to LEDs and power supplies.
• Maximum number of repetitions. Everyone knows that the more repetitions, the more effective the visual effect. Our mirrors give about 20 repetitions. In certain cases we do more.
• Very deep tables. Want deep reflection? No problem. We will achieve this without interfering with the appearance of the table.
• Installing additional lighting. We illuminate not only the inside, but also the outside.
• Additional curly patterns. Using professional equipment Let's add a beautiful patterned cutting to the table.

How we make a table with an infinity mirror

When installing an LED strip, we turn to the section of physics - Optics. We believe that carrying out calculations according to the laws of optics is mandatory, and only with strict adherence to all proportions can ideal dispersion and reflection of light from LEDs be achieved.

Additional table lighting

When installing lighting inside, creating an infinity tunnel, we always suggest additional illumination of the table from the outside. We basically use the same color as the inside. This technique visually expands the visual perception of the infinity tunnel. But if desired, we can add adjacent colors, for example, the backlight is red, and around it is a few tones lower or orange. There are a lot of options for creativity.

Additional patterns

Using various styles When decorating a table, sometimes it wouldn’t be a bad idea to resort to a certain design option, for example, “Baroque” or “Gothic”. We will add beautiful stenciled patterns symmetrically from the infinity tunnel, which we will highlight in any color of the client’s choice.

Below you can choose a ready-made table with standard sizes. But if you need a table with non-standard parameters: round, oval or other irregular shape, lighting according to own design etc. - Please, Contact us and we will be happy to fulfill your order as soon as possible.

Beautiful and original furniture attracts the eye. You can look at it endlessly; you want to surround your space with it both at home and at work. But many people know that designer tables or the chairs are not at all budget-friendly. However, if your hands grow where you need and eat minimum set working tools, then creating original furniture you are quite capable. The DIY infinity table is direct proof of this. And you will find out this by carefully reading our article.

Unusual table

This invention is not the work of a design department. furniture factory or a designer who never leaves the pages of glossy magazines. Instructions for creating such a table with an infinity effect with your own hands appeared on the photo hosting site “Imgur”. In just a few hours, the post received more than 60 thousand views. And it turned out that its author was an American high school student who spent three months preparing the project for the youth forum.

Many people liked his invention, and the instructions for creating a table with an infinity effect with their own hands were immediately tested by dozens of craftsmen. Such simple furniture suitable for any room:

• A table with homemade lighting will fit perfectly into the office interior. Any visitor will immediately pay attention to such furniture and everyone will remember it. It will not be surprising if they want to visit your office again.
• In an apartment or private house, such a table would also be quite appropriate. It is ideal for family and romantic meetings. When fully served, it will cause delight and genuine interest among your guests.

Important! At first it seems that there is nothing special about this table, as long as the backlight is turned off. But as soon as the LEDs installed around the perimeter of the tabletop start working, a feeling of a bottomless surface appears. It looks amazing with the lights on, but it's even more impressive in the dark with the main lights off.

The illusion of infinity

When creating a seemingly complex 3D table with your own hands, a simple display principle is taken as a basis:

• The infinity effect is achieved quite simply - using LED lighting around the perimeter, made in various color variations.
• Table top in in this case is a DIY design of mirrors with an infinity effect.
• To light radiation was as visible as possible; the top glass in this design is made of translucent material.
• Experts advise choosing red diodes. It is he who is less prone to scattering than others, so the visual tunnel will seem deeper.
• To control the backlight, the on/off button or a special remote control can be used.

Some craftsmen use simple garlands when creating a backlit table with their own hands. But it’s still better to use LEDs, as they have a number of advantages:

• More saturated and deeper light than using conventional lamps;
• LED strips are quite durable and resistant to any vibrations;
• Ice lamps burn out much less often; each of them can work continuously for about 100 hours;
• The color range of LEDs is much richer and more varied;
• The service life of the Ice backlight is not affected by the number of turns on and off;
• They are environmentally friendly and safe;
• With all the advantages, LEDs are also much cheaper than conventional lamps;
• Impacts low temperatures they are not afraid.

Important! Today, there are several ways to connect an LED strip to various sources power supply, be it a regular outlet or a computer. It all depends on your imagination and financial capabilities.

Table installation

As we have already said, finding such furniture in a store or market will be quite difficult. Therefore, a DIY table with an infinity effect is the easiest way to get an exclusive item in your interior. To do this, it is enough to know the sequence of actions and focus on the result.

Materials and tools

Of course, when creating a 3D table with your own hands, you cannot do without tools and materials. During this work you will need:

• lumber to create the table itself - both wood and chipboard are suitable for this;
• sandpaper for wood processing, however, if you are working with already ready-made parts, ordered at production, this material can be excluded from the list;
• a mirror of a suitable diameter, which will serve as the base of the tabletop;
• translucent mirror - it should be 10 cm larger than a regular mirror, since this part is installed on top of the tabletop and covers all parts of the upper structure;
• LED strip - its length will depend on the size of your future table with DIY lighting;
• power supply for LEDs and wires;
• self-tapping screws;
• Super glue;
• Double-sided tape;
• screwdriver

Important! If at this stage you have a question, how to make an infinity mirror with your own hands, then the tinted surface can be replaced with a regular one, having first applied a tint film to it. There is also an alternative to a regular mirror:

• To do this, food foil is glued to the glass;
• For work, mirror-coated glass is purchased.

If you doubt whether glass with a reflective coating is suitable for making a coffee table with an infinity effect with your own hands, then you can check it as follows:

1. Carefully, so as not to drop, place the mirror and glass in front of each other.
2. Any light source - an ordinary lamp, and better backlighting, which you will use, place between them.
3. Evaluate the resulting effect.

When preparatory stage finished, it's time to start assembling the 3D table with your own hands.

Drawing development

First of all, you will need a design drawing, drawn up taking into account all the dimensions of the future piece of furniture:

• Before you start assembling the infinity coffee table with your own hands, you need to think about where the electrical elements, affecting the quality of illumination and the creation of the desired effect.
• After this, it is necessary to mark the exact location of the socket, switch, and potentiometer on the drawing.

When assembling mirrors with an infinity effect with your own hands, you must take into account one very important factor - the depth of the tunnel that you want to see in the finished furniture. It is achieved by maintaining a certain distance between the tabletop parts:

• if you want to know in advance what the depth of the tunnel will be, then multiply the distance between the mirrors by 16 to get the approximate apparent depth of the tunnel;
• if you are not satisfied with the result, then when drawing up the drawing, take into account and indicate how much you need to increase the space between the parts of the tabletop;
• In most cases optimal distance There is an 8 cm segment between the lower and upper mirrors, but here everything depends only on your preferences.

After the drawing has been drawn up, you can begin assembling the backlit table with your own hands.

Base assembly

In order to get a new one, original item interior, can already be used ready-made furniture. To do this you will need to detach the tabletop. We suggest considering the option of creating a backlit table with your own hands from scratch:

1. First, we create a strong and durable frame for future furniture. To do this, take 4 boards, 4 metal corner, which will hold the structure together and bottom part designs.
2. Now we use sandpaper. We use it to process the surface and edges of each detail of the future table with the infinity effect with our own hands
3. Using a drill, we make holes for the elements according to the drawing. They also need to be sanded.
4. Let's move on to assembly. To do this, we connect the parts into a single structure; the joints can be additionally glued to increase the possible load on your future backlit table with your own hands.
5. It is better to keep the finished base for 24 hours so that all joints dry out and the structure gains strength.

Assembling the tabletop

Now we move on to creating a mirror with an infinity effect with our own hands, which gives originality to this furniture. As we have already said, you can use mirrors, or you can replace them with glasses with pre-treatment. The second is a more complex option, and we suggest you consider it. In this case, to the list necessary tools It's worth adding a glass cutting device. General scheme the work looks like this:

• Cut out a part from a plexiglass blank required sizes. We calculate the width and length at the stage of drawing up the drawing.
• Then we process the edges of this part in order to simply avoid injuries during work.
• We glue a mirror film onto this part of the future table with the infinity effect with our own hands.

Important! It is better to first spray the surface with water, or even better, with a soap solution. Then, during the gluing process, air bubbles trapped under the film will be easy to remove.

• We cut off the excess film around the edges and wait at least 12 hours for the part to dry thoroughly.

While the mirror is drying, we figure it out general structure table top. In cross section it will look like a layer cake:

1. The base of the structure is a mirror, which is placed with the reflecting side up.
2. The side of the table top body is attached to the main mirror.
3. The front chipboard frame is attached to the installed sidewalls. Its outer diameter, as we have already said, can be equal to external frame table. But the inner one needs to be made a little smaller.
4. A translucent mirror is already installed on the frame of our table with the infinity effect made from wood board.
5. LEDs using double sided tape are attached around the perimeter of the front frame. Moreover, this must be done in such a way that the light bulbs from above are not visible, but they should be reflected in the mirror, which is installed as a base. That's why external dimensions the frames are made larger.
6. The wires are laid inside the frame, which should be hollow. If there is a need to remove the wires, then do it yourself by drilling holes of the required diameter in the legs of the future table with lighting.

After this, we fasten the entire structure of the tabletop with screws and finish assembling the table. It is also worth assembling the control panel. It includes a switch, power slot and potentiometer.

• In order to create a glowing table with an infinity effect with your own hands, you should carefully study the diagram for connecting the LEDs to the power source in advance. If you do something wrong at this stage, it can lead, at best, to short circuit, at worst - to fire.
• As a rule, before work, glass is pasted over with a special protective film to avoid scratches on the surface during the process. If you do not skip this stage, the surface of your furniture will have a presentable appearance.
• If your table is not square but round, then when cutting glass you will need double-sided tape. Using it, secure the router in the middle of the workpiece, then you will be able to make the circle perfectly even.
• When creating a table with an infinity effect with your own hands, you should use only waterproof glue. Surely, when further exploitation you will spend wet cleaning furniture, and no one is safe from knocking over a cup of tea onto the surface.
• It is better to secure the LED strip around the perimeter of the tabletop using high-quality double-sided tape. Before assembling the structure together, you should make sure that the LEDs are securely fastened. If even a part comes off while using the table, the integrity of the illusion will be compromised, and you will have to disassemble the entire structure to eliminate this defect.
• LED backlight control parts are best placed in plastic box and secure it under the table top. You should not hide it inside the structure; it is better to leave free access to the block in case of breakdown.

If you have a fairly good knowledge of electrical engineering, you can make a table with spectacular lighting that will respond to movement. For this you will need.