GOST 5336-80

INTERSTATE STANDARD

STEEL BRAIDED MESH
SINGLE

Specifications

Date of introduction 01.01.82

This standard applies to steel woven single mesh with diamond and square mesh , made by weaving flat spirals of steel wire into one loop and used for fencing , thermal insulation works , fastening of mine workings in mines and mines , sifting materials.

(Changed edition , Change No. 1 , 2).

1. MAIN PARAMETERS AND DIMENSIONS

1.1. The grid is divided according to the shape of the cells:

rhombic - P (the acute angle of the rhombus should be 60 ° ) - ;

by surface type:

without cover ,

made of galvanized wire - 0.

Based on the accuracy of the cell size, the grids are divided into groups 1 and 2.

(Changed edition , Change No. 1 , 2).

1.2. The size of the clear side of the cell and the diameter of the wire must correspond to those specified in.

It is allowed, by agreement between the consumer and the manufacturer, to produce lightweight meshes (LW) No. 20 , 25, 35 of low-carbon thermally untreated uncoated wire with a nominal diameter of 1 , 8 mm instead of 2 , 0 mm; mesh No. 45 made of wire with a diameter of 2 , 0 mm instead of 2 , 5 mm; No. 50 from wire with a diameter of 2 , 5 mm; No. 80 from wire with a diameter of 3 , 0 mm No. 100 from wire with a diameter of 4 , 0 mm.

(Changed edition , Change No. 1 , 3).

Examples of symbols

Mesh with rhombic cell No. 12 , from thermally untreated wire , diameter 1 , 6 mm , Group 1:

Mesh 1-Р-12-1 , 6 GOST 5336-80

Mesh with square cell No. 20 , made of galvanized wire , diameter 2 , 0 mm , Group 2:

Mesh 2-20-2 , 0-0 GOST 5336-80

Mesh with a square cell No. 20 made of wire with a diameter of 1 , 8mm:

Mesh 20-OB GOST 5336-80

(Changed edition , Change No. 2).

1.3. The maximum deviation for the arithmetic mean size of the cell side should not exceed + 6% for meshes of the 1st group and + 10% for meshes of the 2nd group.

(Changed edition , Change No. 1).

1.4. The maximum deviation of the cell angle from the nominal value should not exceed ± 10° .

1.5. The mesh width and maximum deviations must correspond to those specified in.

Mesh No. 15 made of wire with a diameter of 2 , 0 mm can be produced in widths up to 2000 mm.

(Changed edition , Change No. 1).

2. TECHNICAL REQUIREMENTS

Mesh packing , transported to the Far North and hard-to-reach areas , must comply with GOST 15846.

(Changed edition , Change No. 1 , 2).

(Introduced additionally , Change No. 1).

wire and tape according to other regulatory and technical documentation.

The weight of the package is no more than 1 ton.

Nets are transported by all types of transport in accordance with the rules for the carriage of goods. , applicable for transport of this type and Technical conditions for loading and securing cargo , approved by the USSR Ministry of Railways. Transportation by rail is carried out by carload or small shipments. On open rolling stock, the mesh is transported only in packages.

The conditions for transporting the mesh in terms of exposure to climatic factors must comply with storage conditions 5 and 8 according to GOST 15150.

(Changed edition , Change No. 1 , 2, 3).

(Changed edition , Change No. 1).

APPLICATION
Information

Table of live section and theoretical mass of 1 m 2 mesh

STEEL BRAIDED MESH
SINGLE

TECHNICAL CONDITIONS

GOST 5336-80

PUBLISHING HOUSE OF STANDARDS

STATE STANDARD OF THE USSR UNION

Date of introduction 01.01.82

This standard applies to steel woven single mesh with rhombic and square cells, made by weaving flat spirals of steel wire into one loop and used for fencing, thermal insulation work, fastening mine workings in mines and mines, and sifting materials.

1. MAIN PARAMETERS AND DIMENSIONS

1.1. The grid is divided according to the shape of the cells:

rhombic - P (the acute angle of the rhombus should be 60°) - ;

by surface type:

without cover,

made of galvanized wire - 0.

Based on the accuracy of the cell size, the grids are divided into groups 1 and 2.

(Changed edition, Amendment No. 1, 2).

1.2. The size of the clear side of the cell and the diameter of the wire must correspond to those indicated in the table. 1.

Table 1

It is allowed, by agreement between the consumer and the manufacturer, to produce lightweight meshes (LG) No. 20, 25, 35 from low-carbon thermally untreated uncoated wire with a nominal diameter of 1.8 mm instead of 2.0 mm; mesh No. 45 made of wire with a diameter of 2.0 mm instead of 2.5 mm; No. 50 from wire with a diameter of 2.5 mm; No. 80 from wire with a diameter of 3.0 mm No. 100 from wire with a diameter of 4.0 mm.

Examples of symbols

Mesh with rhombic cell No. 12, made of thermally untreated wire, diameter 1.6 mm, group 1:

Mesh 1-R-12-1.6 GOST 5336-80

Mesh with square mesh No. 20, galvanized wire, diameter 2.0 mm, group 2:

Mesh 2-20-2.0-0 GOST 5336-80

Mesh with square cell No. 20 made of wire with a diameter of 1.8 mm:

Mesh 20-OB GOST 5336-80

1.3. The maximum deviation for the arithmetic mean size of the cell side should not exceed + 6% for meshes of the 1st group and + 10% for meshes of the 2nd group.

1.4. The maximum deviation of the cell angle from the nominal one should not exceed ± 10°.

1.5. The mesh width and maximum deviations must correspond to those indicated in the table. 2.

Mesh No. 15 made of wire with a diameter of 2.0 mm can be made up to 2000 mm wide.

table 2

(Changed edition, Amendment No. 1).

2. TECHNICAL REQUIREMENTS

2.1. Meshes must be manufactured in accordance with the requirements of this standard according to technological regulations approved in the prescribed manner, from low-carbon thermally untreated uncoated or galvanized wire of normal manufacturing accuracy according to TU 14-4-1563-89.

Meshes of the 1st group must be made of wire with minus maximum deviations equal to the sum of the absolute values ​​of the maximum deviations.

(Changed edition, Amendment No. 1, 3).

2.2. Each spiral must consist of one wire.

2.3. Adjacent spirals must be woven into each other with all turns without gaps.

2.4. There should be no inverted spirals in the grid.

(Changed edition, Amendment No. 2).

2.5. The ends of the spirals on both sides of the mesh must be cut off and each end at the junction must be bent to its own spiral.

2.6. After production, the nets are rolled into rolls. The roll must consist of one piece of mesh with a length of at least 5 m for grids No. 5-60 and at least 3 m for grids No. 80, 100.

It is allowed to roll rolls from two pieces stitched in a spiral.

For meshes of the 1st group, the roll must consist of one piece with a length of at least 10 m for meshes No. 5-60 and at least 5 m for meshes No. 80, 100.

(Changed edition, Amendment No. 1, 2).

2.7. The weight of the roll should not exceed 80 kg. For meshes No. 80 and 100, it is allowed to increase the weight of the mesh roll to 250 kg.

(Changed edition, Amendment No. 1).

3. ACCEPTANCE RULES

3.1. Nets are accepted in batches. The batch must consist of meshes of the same number, the same width, the same material and be issued with one quality document. The quality document must contain:

trademark or name and trademark of the manufacturer;

grid symbol;

width in millimeters and mesh length in meters, total amount of mesh in square meters;

number of rolls in a batch.

(Changed edition, Amendment No. 1).

3.2. To check the quality of the weave, the bending of the ends of the spiral, the arithmetic average of the size of the side of the cell in the light, the length, width of the mesh and the angle of the cell, 5% of the rolls are selected from the batch, but not less than two.

(Changed edition, Amendment No. 2).

3.3. If unsatisfactory test results are obtained for at least one of the indicators, a re-check is carried out on a double number of rolls.

The results of the re-inspection are applied to the entire batch.

(Changed edition, Amendment No. 1).

4. TEST METHODS

4.1. The quality of the weave and the bending of the ends of the spirals are determined visually when rewinding the mesh rolls.

4.2. The arithmetic mean value of the cell side size in the light is determined in three places of the grid, spaced from the edge by at least 100 mm, counted in two directions parallel to the sides of the cell, 10 cells for grids No. 5-15 and 5 cells for grids No. 20 -100 and measure the length of the section, including one outer wire on which the counted cells are located. The length of the section to determine the arithmetic mean value of the cell side size in the light is measured with a meter or a ruler with a division value of 1 mm.

The arithmetic mean value of the cell side size in the light ( A), mm, calculated using the formula

Where l- length of the section on which 5 or 10 cells are located sequentially counted in the corresponding directions, mm;

n- number of counted cells;

d- nominal wire diameter, mm.

The final value of the arithmetic mean size of the cell side in the light is determined as the arithmetic mean of six measurements.

4.3. The wire diameter is measured with a micrometer according to GOST 6507-90 before making the mesh.

(Changed edition, Amendment No. 2).

4.4. The width of the mesh is measured by the protruding curved ends of the wires with a meter or tape measure with a division value of 1 mm. The length of the mesh is measured in a tensioned state, excluding changes in the shape of the cells, with a meter or tape measure with a division value of 1 mm or a counter.

4.5. The cell angle is checked with a protractor according to GOST 5378-88 or with a template in three places on the grid, but no closer than 2 cells from the edge of the grid.

5. PACKAGING, LABELING, TRANSPORTATION AND STORAGE

Packaging of mesh transported to the Far North and hard-to-reach areas must comply with GOST 15846-79.

(Changed edition, Amendment No. 1, 2).

5.3. At the consumer's request, the mesh is coated with ZhKB conservation lubricant according to the approved technical documentation or with a mixture of ZhKB and industrial oil in accordance with GOST 20799-88 in a 1:1 ratio.

5.4. A label must be attached to the end of the roll or bag indicating:

trademark or name and trademark of the manufacturer;

name and trademark of the manufacturer;

grid symbol;

width in millimeters and mesh length in meters, total amount of mesh in square meters.

5.3 - 5.4. (Changed edition, Amendment No. 1).

5.4a. Transport marking - according to GOST 14192-77.

(Introduced additionally, Amendment No. 1).

5.5. The mesh is transported in bags according to GOST 26663-76 or in rolls. It is possible to form packages without using pallets.

Roll diameter - from 200 to 600 mm, length - from 1000 to 3000 mm. The package is formed from rolls. Overall dimensions of the package: length from 1000 to 3000 mm, width from 1870 mm, height up to 1400 mm. An enlarged cargo package is formed when two or more rolls are transported to the consumer.

Packaging means are:

wire rod with a diameter of 6.5 mm according to GOST 14085-79;

wire and tape according to other regulatory and technical documentation.

The weight of the package is no more than 1 ton.

Nets are transported by transport of all types in accordance with the rules for the transportation of goods in force for this type of transport and the Technical Conditions for Loading and Securing Cargo, approved by the Ministry of Railways of the USSR. Transportation by rail is carried out by carload or small shipments. On open rolling stock, the mesh is transported only in packages.

The conditions for transporting the mesh in terms of exposure to climatic factors must comply with storage conditions 5 and 8 according to GOST 15150-69.

(Changed edition, Amendment No. 1, 2, 3).

5.6. Storage of nets must comply with conditions 5 according to GOST 15150-69.

(Changed edition, Amendment No. 1).

APPLICATION

Information

Table of live section and theoretical mass of 1 m2 mesh

Note. The values ​​given in parentheses apply to square mesh grids.

(Changed edition, Amendment No. 2, 3).

INFORMATION DATA

1. DEVELOPED AND INTRODUCED by the USSR Ministry of Metallurgy

DEVELOPERS

K.G. Zalyalutdinov, N.A. Galkina, V.D. Egorov, L.A. Parshina, G.L. Cedun

2. APPROVED AND ENTERED INTO EFFECT by Resolution of the USSR State Committee on Standards dated March 31, 1980 No. 1466

3. INSTEAD GOST 5336-67

4. REFERENCE REGULATIVE AND TECHNICAL DOCUMENTS

TU 14-15-213-89

TU 14-4-1563-89

5. The validity period was removed by Decree of the USSR State Standard of 04/08/91 No. 457

6. REISSUE (December 1992) with Amendments No. 1, 2, 3, approved in September 1986, April 1991 (IUS 12-86, 6-89, 7-91)

OST 14.15.193-86

OST 14-4-210-87

TU 14-4-1563-89

5. The validity period was removed by Decree of the USSR State Standard of 04/08/91 N 457

6. EDITION with Amendments No. 1, 2, 3, approved in September 1986, March 1989, April 1991 (IUS 12-86, 6-89, 7-91)


This standard applies to steel woven single mesh with rhombic and square cells, made by weaving flat spirals of round steel wire into one loop and used for fencing, thermal insulation work, fastening mine workings in mines and mines, and sifting materials.

1. MAIN PARAMETERS AND DIMENSIONS

1.1. Grids are divided into:

- according to the shape of the cells:

rhombic - P (the acute angle of the rhombus should be 60°) - drawing 1;

square - drawing 2;

- by surface type:

without cover;

made of galvanized wire - 0.

Based on the accuracy of the cell size, the grids are divided into groups 1 and 2.

(Changed edition, Amendment No. 1, 2).

1.2. The size of the clear side of the cell and the diameter of the wire must correspond to those indicated in Table 1.

Table 1

It is allowed, by agreement between the consumer and the manufacturer, to produce lightweight meshes (LG) NN 20, 25, 35 from low-carbon thermally untreated uncoated wire with a nominal diameter of 1.8 mm instead of 2.0 mm; mesh N 45 made of wire with a diameter of 2.0 mm instead of 2.5 mm; N 50 from wire with a diameter of 2.5 mm; N 80 from wire with a diameter of 3.0 mm and N 100 from wire with a diameter of 4.0 mm.



Examples of symbols

Mesh with rhombic cell N 12, made of thermally untreated wire with a diameter of 1.6 mm, group 1:

Mesh 1-R-12-1.6 GOST 5336-80

Mesh with square mesh N 20, made of galvanized wire with a diameter of 2.0 mm, group 2:

 Mesh 2-20-2.0-0 GOST 5336-80

Mesh with square mesh N 20, lightweight, made of wire with a diameter of 1.8 mm:

 Mesh 20-OB GOST 5336-80

1.3. The maximum deviation for the arithmetic mean size of the cell side should not exceed +6% for meshes of group 1 and +10% for meshes of group 2.

1.4. The maximum deviation of the cell angle from the nominal one should not exceed ±10°.

1.5. The mesh width and maximum deviations must correspond to those indicated in Table 2.

Mesh N 15 made of wire with a diameter of 2.0 mm can be made up to 2000 mm wide.

table 2

(Changed edition, Amendment No. 1).

2. TECHNICAL REQUIREMENTS

2.1. Meshes must be manufactured in accordance with the requirements of this standard according to technological regulations approved in the prescribed manner, from low-carbon thermally untreated uncoated or galvanized wire of normal manufacturing accuracy according to TU 14-4-1563.

Group 1 meshes must be made of wire with minus maximum deviations equal to the sum of the absolute values ​​of the maximum deviations.

(Changed edition, Amendment No. 1, 3).

2.2. Each spiral must consist of one wire.

2.3. Adjacent spirals must be woven into each other with all turns without gaps.

2.4. There should be no inverted spirals in the grid.

(Changed edition, Amendment No. 2).

2.5. The ends of the spirals on both sides of the mesh must be cut off and each end at the junction must be bent to its own spiral.

2.6. After production, the nets are rolled into rolls. The roll must consist of one piece of mesh with a length of at least 5 m for mesh NN 5-60 and at least 3 m for mesh NN 80, 100.

It is allowed to roll rolls from two pieces stitched in a spiral.

For group 1 meshes, the roll must consist of one piece with a length of at least 10 m for meshes NN 5-60 and at least 5 m for meshes NN 80, 100.

(Changed edition, Amendment No. 1, 2).

2.7. The weight of the roll should not exceed 80 kg. For meshes NN 80 and 100, it is allowed to increase the weight of the mesh roll to 250 kg.

(Changed edition, Amendment No. 1).

3. ACCEPTANCE RULES

3.1. Nets are accepted in batches. The batch must consist of meshes of the same number, the same width, the same material and be issued with one quality document. The quality document must contain:



- symbol of the grid;

- width in millimeters and mesh length in meters, total amount of mesh in square meters;

- number of rolls in the batch.

(Changed edition, Amendment No. 1).

3.2. To check the quality of the weave, the bending of the ends of the spiral, the arithmetic average of the size of the side of the cell in the light, the length, width of the mesh and the angle of the cell, 5% of the rolls are selected from the batch, but not less than two.

(Changed edition, Amendment No. 2).

3.3. If unsatisfactory test results are obtained for at least one of the indicators, it is retested on a double number of rolls.

The results of the re-inspection are applied to the entire batch.

(Changed edition, Amendment No. 1).

4. TEST METHODS

4.1. The quality of the weave and the bending of the ends of the spirals are determined visually when rewinding the mesh rolls.

4.2. The arithmetic mean value of the cell side size in the light is determined in three places of the grid, spaced from the edge by at least 100 mm, counted in two directions parallel to the sides of the cell, 10 cells for grids NN 5-15 and five cells for grids NN 20-100 and measure the length of the section, including one extreme wire, on which the counted cells are located. The length of the section to determine the arithmetic mean value of the cell side size in the light is measured with a meter or a ruler with a division value of 1 mm.

The arithmetic mean value of the cell side size in light (), mm, is calculated using the formula

where is the length of the section on which five or 10 cells are located sequentially counted in the corresponding directions, mm;

- number of counted cells;

- nominal wire diameter, mm.

The final value of the arithmetic mean size of the cell side in the light is determined as the arithmetic mean of six measurements.

4.3. The diameter of the wire is measured with a micrometer according to GOST 6507 before making the mesh.

(Changed edition, Amendment No. 2).

4.4. The width of the mesh is measured by the protruding curved ends of the wires with a meter or tape measure with a division value of 1 mm. The length of the mesh is measured in a tensioned state, excluding changes in the shape of the cells, using a meter or tape with a division of 1 mm, or a counter.

4.5. The cell angle is checked using a protractor GOST 5378 or a template in three places on the grid, but no closer than two cells from the edge of the grid.

5. PACKAGING, LABELING, TRANSPORTATION AND STORAGE

5.1. Each roll of mesh should be tied with low-carbon wire with a diameter of 1.2-2.5 mm GOST 3282 or TU 14-4-1563 or waste of this wire in the middle and along the edges, or the end of the mesh should be tied with the same wire to the roll in the middle and along the edges.

(Changed edition, Amendment No. 1, 3).

5.2. The ends of the roll should be wrapped in paper GOST 8828 or other paper manufactured according to normative and technical documentation (NTD), or packaging fabric according to GOST 5530, or containerized canvas-stitched fabric, or glued fabric, or stitched flap from textile industry waste, as well as other materials manufactured according to scientific and technical documentation, excluding the use of cotton and linen fabrics and not compromising the quality of packaging.

It is allowed not to pack mesh NN 5-50 inclusive, but to tie the ends of the wire roll crosswise in accordance with clause 5.1 or in another way, provided that the bent wires are prevented from sticking together.

Packaging materials at the ends of the rolls are tied with wire in accordance with clause 5.1.

The packaging of mesh transported to the Far North and hard-to-reach areas must comply GOST 15846.

(Changed edition, Amendment No. 1, 2).

5.3. At the consumer's request, the mesh is coated with ZhKB conservation lubricant approved in the established manner or with a mixture of ZhKB and industrial oil according to GOST 20799 in a 1:1 ratio.

5.4. A label must be attached to the end of the roll or bag indicating:

- trademark or name and trademark of the manufacturer;

- name and trademark of the manufacturer;

- symbol of the grid;

- width in millimeters and mesh length in meters, total amount of mesh in square meters.

5.3-5.4. (Changed edition, Amendment No. 1).

5.4a. Transport marking - by GOST 14192.

(Introduced additionally, Amendment No. 1).

5.5. The nets are transported in packages by GOST 26663 or rolls. It is possible to form packages without using pallets.

Roll diameter - from 200 to 600 mm, length - from 1000 to 3000 mm. The package is formed from rolls. Overall dimensions of the package: length from 1000 to 3000 mm, width from 1870 mm, height up to 1400 mm. An enlarged cargo package is formed when two or more rolls are transported to the consumer.

Packaging means are:

- wire rod with a diameter of 6.5 mm according to OST 14.15.193;

- wire harnesses GOST 3282 or according to OST 14-4-210;

- strappings from tape GOST 3560 ;

- wire and tape according to another technical documentation.

Package weight - no more than 1 ton.

Nets are transported by all types of transport in accordance with the rules for the carriage of goods in force for this type of transport and the Technical Conditions for Loading and Securing Cargo*, approved by the Ministry of Railways. Transportation by rail is carried out by carload or small shipments. On open rolling stock, the mesh is transported only in packages.
________________
*Probably an error in the original. Should read: "Technical conditions for loading and securing cargo". - Database manufacturer's note.

The conditions for transporting the mesh in terms of exposure to climatic factors must correspond to storage conditions 5 and 8 according to GOST 15150.

(Changed edition, Amendment No. 1, 2, 3).

5.6. Storage of nets must comply with conditions 5 of GOST 15150.

(Changed edition, Amendment No. 1).

APPENDIX (reference). Table of live section and theoretical mass of 1 sq.m of mesh

APPLICATION
Information

Table of live section and theoretical mass of 1 m mesh

Note. The values ​​given in parentheses apply to square mesh grids.

(Changed edition, Amendment No. 2, 3).



The text of the document is verified according to:
official publication
Metal mesh. Types.
Specifications: Sat. GOST. -
M.: IPK Standards Publishing House, 2003

INTERSTATE STANDARD

TECHNICAL CONDITIONS

Official publication

Standardinform

INTERSTATE STANDARD

SINGLE STEEL BRAIDED MESH

Specifications

Single woven steel wire cloth. Specifications

MKS 77.140.65 OKP 12 7500

Date of introduction 01/01/82

This standard applies to steel woven single mesh with rhombic and square cells, made by weaving flat spirals of round steel wire into one loop and used for fencing, thermal insulation work, fastening mine workings in mines and mines, and sifting materials.

1. MAIN PARAMETERS AND DIMENSIONS

1.1. The grid is divided according to the shape of the cells:

rhombic - P (the acute angle of the rhombus should be 60°) - damn. 1; square - damn. 2; by surface type: uncoated,

made of galvanized wire - 0.

Based on the accuracy of the cell size, the grids are divided into groups 1 and 2.

(Changed edition, Amendment No. 1, 2).

1.2. The size of the clear side of the cell and the diameter of the wire must correspond to those indicated in the table. 1.

Table 1

© Standardinform, 2007

Continuation of the table. 1

With diamond or square mesh

With square cell

It is allowed, by agreement between the consumer and the manufacturer, to produce lightweight meshes (LG) No. 20, 25, 35 from low-carbon thermally untreated uncoated wire with a nominal diameter of 1.8 mm instead of 2.0 mm; mesh No. 45 made of wire with a diameter of 2.0 mm instead

2.5 mm; No. 50 from wire with a diameter of 2.5 mm; No. 80 made of wire with a diameter of 3.0 mm and No. 100 made of wire with a diameter of 4.0 mm.

Examples of symbols

Mesh with rhombic cell No. 12, made of thermally untreated wire, diameter

1.6 mm, groups 1:

Mesh 1-R-12-1.6 GOST 5336-80

Mesh with square mesh No. 20, galvanized wire, diameter 2.0 mm, group 2:

Mesh 2-20-2.0-0 GOST 5336-80

Mesh with a square cell No. 20, lightweight, made of wire with a diameter of 1.8 mm:

Mesh 20-OB GOST 5336-80

1.3. The maximum deviation for the arithmetic mean size of the cell side should not exceed + 6% for meshes of the 1st group and + 10% for meshes of the 2nd group.

1.4. The maximum deviation of the cell angle from the nominal one should not exceed ± 10°.

1.5. The mesh width and maximum deviations must correspond to those indicated in the table. 2. Mesh No. 15 made of wire with a diameter of 2.0 mm can be made up to 2000 mm wide.

table 2

(Changed edition, Amendment No. 1).

2. TECHNICAL REQUIREMENTS

2.1. Meshes must be manufactured in accordance with the requirements of this standard according to technological regulations approved in the prescribed manner, from low-carbon thermally untreated uncoated or galvanized wire of normal manufacturing accuracy according to TU 14-4-1563.

Meshes of the 1st group must be made of wire with minus maximum deviations equal to the sum of the absolute values ​​of the maximum deviations.

(Changed edition, Amendment No. 1, 3).

2.2. Each spiral must consist of one wire.

2.3. Adjacent spirals must be woven into each other with all turns without gaps.

2.4. There should be no inverted spirals in the grid.

(Changed edition, Amendment No. 2).

2.5. The ends of the spirals on both sides of the mesh must be cut off and each end at the junction must be bent to its own spiral.

2.6. After production, the nets are rolled into rolls. The roll must consist of one piece of mesh with a length of at least 5 m for grids No. 5-60 and at least 3 m for grids No. 80, 100.

It is allowed to roll rolls from two pieces stitched in a spiral.

For meshes of the 1st group, the roll must consist of one piece with a length of at least 10 m for meshes No. 5-60 and at least 5 m for meshes No. 80, 100.

(Changed edition, Amendment No. 1, 2).

2.7. The weight of the roll should not exceed 80 kg. For meshes No. 80 and 100, it is allowed to increase the weight of the mesh roll to 250 kg.

(Changed edition, Amendment No. 1).

3. ACCEPTANCE RULES

3.1. Nets are accepted in batches. The batch must consist of meshes of the same number, the same width, the same material and be issued with one quality document. The quality document must contain:

grid symbol;

width in millimeters and mesh length in meters, total amount of mesh in square meters;

number of rolls in a batch.

(Changed edition, Amendment No. 1).

3.2. To check the quality of the weave, the bending of the ends of the spiral, the arithmetic average of the size of the side of the cell in the light, the length, width of the mesh and the angle of the cell, 5% of the rolls are selected from the batch, but not less than two.

(Changed edition, Amendment No. 2).

3.3. If unsatisfactory test results are obtained for at least one of the indicators, a re-check is carried out on a double number of rolls.

The results of the re-inspection are applied to the entire batch.

(Changed edition, Amendment No. 1).

4. TEST METHODS

4.1. The quality of the weave and the bending of the ends of the spirals are determined visually when rewinding the mesh rolls.

4.2. The arithmetic mean value of the cell side size in the light is determined in three places of the grid, spaced from the edge by at least 100 mm, counted in two directions parallel to the sides of the cell, 10 cells for grids No. 5-15 and 5 cells for grids No. 20 -100 and measure the length of the section, including one outer wire on which the counted cells are located. The length of the section to determine the arithmetic mean value of the cell side size in the light is measured with a meter or a ruler with a division value of 1 mm.

The arithmetic mean value of the clear cell side size (a), mm, is calculated using the formula

where I is the length of the section on which 5 or 10 cells are located sequentially counted in the corresponding directions, mm; n - number of counted cells; d - nominal wire diameter, mm.

The final value of the arithmetic mean size of the cell side in the light is determined as the arithmetic mean of six measurements.

4.3. The wire diameter is measured with a micrometer according to GOST 6507 before making the mesh.

(Changed edition, Amendment No. 2).

4.4. The width of the mesh is measured by the protruding curved ends of the wires with a meter or tape measure with a division value of 1 mm. The length of the mesh is measured in a tensioned state, excluding changes in the shape of the cells, with a meter or tape measure with a division value of 1 mm or a counter.

4.5. The cell angle is checked with a protractor according to GOST 5378 or a template in three places on the grid, but no closer than 2 cells from the edge of the grid.

5. PACKAGING, LABELING, TRANSPORTATION AND STORAGE

5.1. Each roll of mesh must be tied with low-carbon wire with a diameter of 1.2-2.5 mm in accordance with GOST 3282 or TU 14-4-1563 or waste of this wire in the middle and along the edges, or the end of the mesh sheet must be tied with the same wire to the roll in the middle and along edges.

(Changed edition, Amendment No. 1, 3).

5.2. The ends of the roll must be wrapped with paper in accordance with GOST 8828 or other paper made in accordance with regulatory and technical documentation, or packaging fabric in accordance with GOST 5530, or container stitched canvas, or glued fabric, or sewn flap from textile industry waste, as well as other materials made according to regulatory and technical documentation, excluding the use of cotton and linen fabrics and not compromising the quality of packaging.

It is permissible not to pack meshes No. 5-50 inclusive, but to necessarily tie the ends of the wire roll crosswise in accordance with clause 5.1 or by another method of tying the roll, provided that the bent wires do not adhere to each other.

Packaging materials at the ends of the rolls are tied with wire in accordance with clause 5.1.

Packaging of mesh transported to the Far North and equivalent areas must comply with GOST 15846.

(Changed edition, Amendment No. 1, 2).

5.3. At the consumer's request, the mesh is coated with ZhKB conservation lubricant according to the approved technical documentation or with a mixture of ZhKB and industrial oil in accordance with GOST 20799 in a 1:1 ratio.

5.4. A label must be attached to the end of the roll or bag indicating:

trademark or name and trademark of the manufacturer;

name and trademark of the manufacturer;

grid symbol;

width in millimeters and mesh length in meters, total amount of mesh in square meters.

5.3-5.4. (Changed edition, Amendment No. 1).

5.4a. Transport marking - according to GOST 14192.

(Introduced additionally, Amendment No. 1).

5.5. The mesh is transported in bags according to GOST 26663 or in rolls. It is possible to form packages without using pallets.

Roll diameter - from 200 to 600 mm, length - from 1000 to 3000 mm. The package is formed from rolls. Overall dimensions of the package: length from 1000 to 3000 mm, width from 1870 mm, height up to 1400 mm. An enlarged cargo package is formed when two or more rolls are transported to the consumer.

Packaging means are:

wire rod with a diameter of 6.5 mm according to OST 14.15.193;

wire harnesses in accordance with GOST 3282 or OST 14-4-210;

tape strapping according to GOST 3560;

wire and tape according to other regulatory and technical documentation.

The weight of the package is no more than 1 ton.

Nets are transported by transport of all types in accordance with the rules for the transportation of goods in force for this type of transport and the Technical Conditions for Loading and Securing Cargo, approved by the Ministry of Railways of the USSR. Transportation by rail is carried out by carload or small shipments. On open rolling stock, the mesh is transported only in packages.

The conditions for transporting the mesh in terms of exposure to climatic factors must comply with storage conditions 5 and 8 according to GOST 15150.

(Changed edition, Amendment No. 1, 2, 3).

5.6. Storage of nets must comply with conditions 5 according to GOST 15150.

(Changed edition, Amendment No. 1).

APPLICATION

Information

Table of live section and theoretical mass of 1 m mesh

Mesh with rhombic or square mesh

Square mesh

Note. The values ​​given in parentheses apply to square mesh grids. (Changed edition, Amendment No. 2, 3).

INFORMATION DATA

1. DEVELOPED AND INTRODUCED by the USSR Ministry of Metallurgy

2. APPROVED AND ENTERED INTO EFFECT by Resolution of the USSR State Committee on Standards dated March 31, 1980 No. 1466

3. INSTEAD GOST 5336-67

4. REFERENCE REGULATIVE AND TECHNICAL DOCUMENTS

5. The validity period was removed by Decree of the USSR State Standard of 04/08/91 No. 457

6. EDITION (March 2007) with Amendments No. 1, 2, 3, approved in September 1986, March 1989, April 1991 (IUS 12-86, 6-89, 7-91)

Editor M.I. Makashova Technical editor L.A. Guseva Proofreader A.S. Chernousova Computer layout I.A. Naleykina

Signed for publication on March 19, 2007. Format 60 x 84 1/s. Offset paper. Times typeface. Offset printing. Uel. pech.l. 0.93. Academician-ed.l. 0.75. Circulation 56 copies. Zach. 254. From 3840.

FSUE "STANDARTINFORM", 123995 Moscow, Granatny lane, 4.

Typed into FSUE "STANDARTINFORM" on a PC.

Printed in the branch of FSUE "STANDARTINFORM" - type. "Moscow Printer", 105062 Moscow, Lyalin lane, 6.

OST 14.15.193-86

OST 14-4-210-87

TU 14-4-1563-89

5. The validity period was removed by Decree of the USSR State Standard of 04/08/91 N 457

6. EDITION with Amendments No. 1, 2, 3, approved in September 1986, March 1989, April 1991 (IUS 12-86, 6-89, 7-91)


This standard applies to steel woven single mesh with rhombic and square cells, made by weaving flat spirals of round steel wire into one loop and used for fencing, thermal insulation work, fastening mine workings in mines and mines, and sifting materials.

1. MAIN PARAMETERS AND DIMENSIONS

1.1. Grids are divided into:

- according to the shape of the cells:

rhombic - P (the acute angle of the rhombus should be 60°) - drawing 1;

square - drawing 2;

- by surface type:

without cover;

made of galvanized wire - 0.

Based on the accuracy of the cell size, the grids are divided into groups 1 and 2.

(Changed edition, Amendment No. 1, 2).

1.2. The size of the clear side of the cell and the diameter of the wire must correspond to those indicated in Table 1.

Table 1

It is allowed, by agreement between the consumer and the manufacturer, to produce lightweight meshes (LG) NN 20, 25, 35 from low-carbon thermally untreated uncoated wire with a nominal diameter of 1.8 mm instead of 2.0 mm; mesh N 45 made of wire with a diameter of 2.0 mm instead of 2.5 mm; N 50 from wire with a diameter of 2.5 mm; N 80 from wire with a diameter of 3.0 mm and N 100 from wire with a diameter of 4.0 mm.



Examples of symbols

Mesh with rhombic cell N 12, made of thermally untreated wire with a diameter of 1.6 mm, group 1:

Mesh 1-Р-12-1.6 GOST 5336-80

Mesh with square mesh N 20, made of galvanized wire with a diameter of 2.0 mm, group 2:

 Grid 2-20-2.0-0 GOST 5336-80

Mesh with square mesh N 20, lightweight, made of wire with a diameter of 1.8 mm:

 Mesh 20-OB GOST 5336-80

1.3. The maximum deviation for the arithmetic mean size of the cell side should not exceed +6% for meshes of group 1 and +10% for meshes of group 2.

1.4. The maximum deviation of the cell angle from the nominal one should not exceed ±10°.

1.5. The mesh width and maximum deviations must correspond to those indicated in Table 2.

Mesh N 15 made of wire with a diameter of 2.0 mm can be made up to 2000 mm wide.

table 2

(Changed edition, Amendment No. 1).

2. TECHNICAL REQUIREMENTS

2.1. Meshes must be manufactured in accordance with the requirements of this standard according to technological regulations approved in the prescribed manner, from low-carbon thermally untreated uncoated or galvanized wire of normal manufacturing accuracy according to TU 14-4-1563.

Group 1 meshes must be made of wire with minus maximum deviations equal to the sum of the absolute values ​​of the maximum deviations.

(Changed edition, Amendment No. 1, 3).

2.2. Each spiral must consist of one wire.

2.3. Adjacent spirals must be woven into each other with all turns without gaps.

2.4. There should be no inverted spirals in the grid.

(Changed edition, Amendment No. 2).

2.5. The ends of the spirals on both sides of the mesh must be cut off and each end at the junction must be bent to its own spiral.

2.6. After production, the nets are rolled into rolls. The roll must consist of one piece of mesh with a length of at least 5 m for mesh NN 5-60 and at least 3 m for mesh NN 80, 100.

It is allowed to roll rolls from two pieces stitched in a spiral.

For group 1 meshes, the roll must consist of one piece with a length of at least 10 m for meshes NN 5-60 and at least 5 m for meshes NN 80, 100.

(Changed edition, Amendment No. 1, 2).

2.7. The weight of the roll should not exceed 80 kg. For meshes NN 80 and 100, it is allowed to increase the weight of the mesh roll to 250 kg.

(Changed edition, Amendment No. 1).

3. ACCEPTANCE RULES

3.1. Nets are accepted in batches. The batch must consist of meshes of the same number, the same width, the same material and be issued with one quality document. The quality document must contain:



- symbol of the grid;

- width in millimeters and mesh length in meters, total amount of mesh in square meters;

- number of rolls in the batch.

(Changed edition, Amendment No. 1).

3.2. To check the quality of the weave, the bending of the ends of the spiral, the arithmetic average of the size of the side of the cell in the light, the length, width of the mesh and the angle of the cell, 5% of the rolls are selected from the batch, but not less than two.

(Changed edition, Amendment No. 2).

3.3. If unsatisfactory test results are obtained for at least one of the indicators, it is retested on a double number of rolls.

The results of the re-inspection are applied to the entire batch.

(Changed edition, Amendment No. 1).

4. TEST METHODS

4.1. The quality of the weave and the bending of the ends of the spirals are determined visually when rewinding the mesh rolls.

4.2. The arithmetic mean value of the cell side size in the light is determined in three places of the grid, spaced from the edge by at least 100 mm, counted in two directions parallel to the sides of the cell, 10 cells for grids NN 5-15 and five cells for grids NN 20-100 and measure the length of the section, including one extreme wire, on which the counted cells are located. The length of the section to determine the arithmetic mean value of the cell side size in the light is measured with a meter or a ruler with a division value of 1 mm.

The arithmetic mean value of the cell side size in light (), mm, is calculated using the formula

where is the length of the section on which five or 10 cells are located sequentially counted in the corresponding directions, mm;

- number of counted cells;

- nominal wire diameter, mm.

The final value of the arithmetic mean size of the cell side in the light is determined as the arithmetic mean of six measurements.

4.3. The wire diameter is measured with a micrometer according to GOST 6507 before making the mesh.

(Changed edition, Amendment No. 2).

4.4. The width of the mesh is measured by the protruding curved ends of the wires with a meter or tape measure with a division value of 1 mm. The length of the mesh is measured in a tensioned state, excluding changes in the shape of the cells, using a meter or tape with a division of 1 mm, or a counter.

4.5. The cell angle is checked with a protractor according to GOST 5378 or a template in three places on the grid, but no closer than two cells from the edge of the grid.

5. PACKAGING, LABELING, TRANSPORTATION AND STORAGE

5.1. Each roll of mesh should be tied with low-carbon wire with a diameter of 1.2-2.5 mm in accordance with GOST 3282 or TU 14-4-1563 or waste of this wire in the middle and along the edges, or the end of the mesh should be tied with the same wire to the roll in the middle and around the edges.

(Changed edition, Amendment No. 1, 3).

5.2. The ends of the roll must be wrapped with paper in accordance with GOST 8828 or other paper made in accordance with normative and technical documentation (NTD), or packaging fabric in accordance with GOST 5530, or container stitched canvas, or glued fabric, or sewn flap from textile industry waste, as well as others materials manufactured in accordance with scientific and technical regulations, excluding the use of cotton and linen fabrics and not compromising the quality of packaging.

It is allowed not to pack mesh NN 5-50 inclusive, but to tie the ends of the wire roll crosswise in accordance with clause 5.1 or in another way, provided that the bent wires are prevented from sticking together.

Packaging materials at the ends of the rolls are tied with wire in accordance with clause 5.1.

Packaging of mesh transported to the Far North and hard-to-reach areas must comply with GOST 15846.

(Changed edition, Amendment No. 1, 2).

5.3. At the consumer's request, the mesh is coated with ZhKB conservation lubricant approved in the established manner or with a mixture of ZhKB and industrial oil in accordance with GOST 20799 in a 1:1 ratio.

5.4. A label must be attached to the end of the roll or bag indicating:

- trademark or name and trademark of the manufacturer;

- name and trademark of the manufacturer;

- symbol of the grid;

- width in millimeters and mesh length in meters, total amount of mesh in square meters.

5.3-5.4. (Changed edition, Amendment No. 1).

5.4a. Transport marking - according to GOST 14192.

(Introduced additionally, Amendment No. 1).

5.5. The nets are transported in packages in accordance with GOST 26663 or in rolls. It is possible to form packages without using pallets.

Roll diameter - from 200 to 600 mm, length - from 1000 to 3000 mm. The package is formed from rolls. Overall dimensions of the package: length from 1000 to 3000 mm, width from 1870 mm, height up to 1400 mm. An enlarged cargo package is formed when two or more rolls are transported to the consumer.

Packaging means are:

- wire rod with a diameter of 6.5 mm according to OST 14.15.193;

- wire harnesses in accordance with GOST 3282 or OST 14-4-210;

- tape strapping according to GOST 3560;

- wire and tape according to another technical documentation.

Package weight - no more than 1 ton.

Nets are transported by all types of transport in accordance with the rules for the carriage of goods in force for this type of transport and the Technical Conditions for Loading and Securing Cargo*, approved by the Ministry of Railways. Transportation by rail is carried out by carload or small shipments. On open rolling stock, the mesh is transported only in packages.
________________
*Probably an error in the original. You should read: "Technical conditions for loading and securing cargo". - Database manufacturer's note.

The conditions for transporting the mesh in terms of exposure to climatic factors must comply with storage conditions 5 and 8 according to GOST 15150.

(Changed edition, Amendment No. 1, 2, 3).

5.6. Storage of nets must comply with conditions 5 according to GOST 15150.

(Changed edition, Amendment No. 1).

APPENDIX (reference). Table of live section and theoretical mass of 1 sq.m of mesh

APPLICATION
Information

Table of live section and theoretical mass of 1 m mesh

Note. The values ​​given in parentheses apply to square mesh grids.

(Changed edition, Amendment No. 2, 3).



The text of the document is verified according to:
official publication
Metal mesh. Types.
Specifications: Sat. GOST. -
M.: IPK Standards Publishing House, 2003