Disassembling an interior door handle. How to remove and disassemble the door handle of an interior door

Using door handles leads to wear and tear. Renovation required. You can call a professional or carry out the repairs yourself. Before performing work, it is necessary to study the materials in order to clearly understand how to disassemble door handle at the door. Exist different types handles for doors: with and without a lock. Before starting repairs, it is necessary to establish the type of product in order to determine the sequence of actions.

The market has a large selection of handles for interior and exterior doors with and without a lock. All of them are classified into three types:

To disassemble and reassemble door devices Tools required:

• flat or Phillips screwdriver;
• a key with a stop, a sharp awl;
• pliers;
• Adjustable wrench.

Reasons for parsing

Disassembly and assembly technology door mechanisms does not apply to routine work. They are carried out if the fittings have become loose, the screws in the lock need to be tightened, repaired or replaced. Other reasons leading to the disassembly of fittings:

1. Product failure. The performance is impaired due to failure to prevent the mechanism or rough handling. This is one of the most common reasons for product failure.
2. Replacing the model. The production of models is constantly being improved, and there is a need to replace them.
3. Residential renovation. At major renovation The interior of the premises is being updated. Old interior door handles may not fit into a new style, so they need to be replaced.
4. Surface wear. The product may show abrasions, chips, and peeling paint due to Low quality coverings. Therefore, the lock and fittings are disassembled and must be replaced.

Stages of disassembling fittings

The mechanism is disconnected from the door by removing the lining in the upper part located at the locking button. You can remove it using a key; if it is missing, use an awl. To do this, you need to press the stopper of the latch located in the fittings. The handle and axis of the clamp can be easily separated from the body by simply pulling it off. It is necessary to remove the parts and unscrew the screws with a screwdriver; the fittings move away from the door.

Disassembling a stationary handle

If the product is fixed with self-tapping screws, then it is enough to unscrew the screws with a flat screwdriver and remove the fittings. Inspect for damage. If it cannot be repaired, then it must be replaced.
When placing the product on a common rod, it is enough to remove the fastening fragment from one side. The structure must be removed from reverse side. The presence of a rod in the product is checked by turning it counterclockwise while simultaneously holding it with your hand on the other side. If you can turn it, then it is on the rod.
The stationary handle with built-in latch can be removed with a screwdriver, unscrewing the screws and removing the decorative trim.

Disassembling the push handle

Unscrew the screws securing the cover and remove the tetrahedral rod. After this, the fittings can be easily removed. The second overlay is removed, the axial rod and the remaining part of the fittings are removed. The parts are inspected and a decision is made: replace or repair.

Disassembling the round pen

Knob fittings with a lock take longer to dismantle than other devices due to their complex structure. However, let's figure out how to disassemble a round door handle. To do this, you must follow the following steps:

• First, use a screwdriver to remove the flat cover located near the handle;
• press the stopper with a key or other sharp object and pull the product towards you;
• on the removal side, the screws are unscrewed, both parts move away from the door leaf;
• the screws securing the latch are unscrewed.

Handle assembly

To reassemble the handle, you need to perform all the steps in reverse order.

When moving the round handle, you need to insert a latch into the door. It should be adjacent to the closed surface of the door with the oblique part of the tongue.

After installing the products, they are fixed with screws. The key mechanism is mounted on the selected side of the door.

The pressure link is located on the other side and is secured with two screws. Upon completion of installation, the functionality of the product is checked. It should easily turn and return to its original location. The mechanism can be moved slightly to the side and aligned. To do this, its required position is fixed, a bar is attached to the upper part decorative look.

The slot of the retainer must be in the same position with the plate rod square shape, which should fit into the handle smoothly and without distortion.

Finally, the device is hung. It should be deepened inward by pressing against the axis of the clamping link of the fittings. The removable elements are inserted into the clamping part until it stops, and a decorative strip is hung. It remains to make sure that the mechanism is working properly.

The quality of fixation of the fittings is checked. It should turn freely and return to its original place. The check is performed by turning it until it stops both on the side of the latch and the drum latch mechanism.

Today there are a huge number of different types of door handles. All of them are quite reliable, but sometimes they still have to be replaced or repaired. However, a problem arises here - not everyone knows how to disassemble This is the most necessary element of furniture in everyday life.

How to properly remove a door handle mounted on a interior door? Read about it below.

Reasons for dismantling

In most cases, it is necessary to disassemble the handle if:

• she got loose;
• fell into disrepair;
• the lock itself needs to be replaced.

In the first case, there is usually no need to remove it. It is enough to simply tighten the screws holding it, or replace them with thicker ones (if the wood is worn out).

Unfortunately, budget options handles, in principle, cannot last long, and besides, they are made completely unsuitable for repair. The coating on them is usually quite unstable and will quickly peel off during use. Therefore, when they fail, they are simply replaced with a new one.

Often, during renovations, owners decide to replace old handles with new ones that are more suitable for created design or they just look more modern.

When buying a new set, try to choose ones that are made from good metal With minimum quantity constituent elements. Reliable pressure models, for example, should be equipped with bearings - they can serve you for several decades. By the way, quality is very easy to determine: the heavier the fittings, the higher it is.

The most common types of door handles

Most often, the following three types of handles are installed on interior doors:

• stationary;
• nobs (round);
• push.

The latter variety is considered universal, since it can be equally often seen on both entrance and interior doors. This mechanism in its normal position has an extended locking tongue, and when it becomes necessary to enter the room, the handle is pressed and it leaves the grooves. In this case, a lock is usually cut into the canvas, protected by special pads. In order not to damage the latter, disassembly must be carried out as carefully as possible.

In our country, a round handle equipped with a latch is used only on interior doors. Abroad (for example, in the USA) they are often placed on input. It has a key hole on the outside and a locking button on the inside.

Stationary models are installed mainly on swing doors. This design is convenient, but not very functional. In essence, it is an oblong bar on which a U-shaped bracket is attached. In the simplest versions, none locking mechanisms not provided - the door closes with a separate bolt. More advanced models also have a roller latch, installed independently.

Prepare the following tools for dismantling:

• flat and Phillips screwdrivers;
• thrust wrench (included with the product).

If the model is without bolts (that is, with hidden fastenings), then you need to act in this order:

• flat screwdriver (being careful not to damage decorative coating doors) unclip the trim located at the base;
• Unscrew the screws hidden under it;
• use a stop wrench to press directly on the stopper;
• remove the handle by carefully pulling it towards you;
• After dismantling, unscrew the screws holding the locking mechanism.

In simpler round models, disassembly is much easier - just unscrew the two long bolts located on the back side on either side of the latch.

IN in this case you just need to unscrew the self-tapping screws or screws securing the strip to the door leaf.

Here it is worth understanding that replacement of this type handles must be made of a similar size. Otherwise, traces from self-tapping screws will not be hidden. They are especially visible on varnished surfaces.

Individual models are connected with bolts through the door - this method of fastening is convenient for both the manufacturer and the consumer. In this case, you just need to unscrew them from the back and both handles will be removed.

Lever handle

All that is required is to remove the trim (in most models it is connected to the handle). In more simple options you just need to unscrew two screws from the door leaf.

In advanced ones, all fasteners are hidden behind a decorative cap - it either snaps off or is screwed onto a thread. By removing it, you will have access to 3-4 screws that need to be unscrewed with a screwdriver. Don't forget to also remove the clamping screw mounted directly on the handle - it secures the square pivot rod. After this, disassembly can be considered complete.

Assembly nuances

Before placing the handle in its intended place, secure the locking mechanism - turn its oblique surface in the direction of closing the door.

It is important to tighten all screws and screws as tightly as possible - the better you do this, the longer they will not come loose.

After assembly, check how the mechanism works - the latch should fit freely into the groove and ensure reliable fixation.

In all premises without exception, whether it be a house, apartment or office, there is always doors. This means that when arranging them, you won’t be able to ignore the moment of selecting fittings for them, such as door handles. You need to dwell in detail on their types and selection parameters, but before you start selecting, it makes sense to find out how to remove the handle from doors: internal or input.

Learning to remove the handle

Quality

The main criterion when choosing a door handle is its quality. After all, it is in operation regularly, since with its help the closing and opening of any doors. In addition, she plays an important artistic role in the interior of each room. In any hardware store You can find a wide selection of door fittings, among which everyone will find what they need. Handles for internal and entrance doors They are distinguished not only by cost and design, but also by the material of manufacture.

If there are often drafts in the room, we recommend purchasing a handle with a latch lock. This will help doors remain closed and you won't be forced to close it regularly. When selecting such a device, you should carefully check the mechanism for serviceability and smooth operation.

Device types

1. Push. The mechanism forces the lock latch to work when influenced. The tongue moves in inner part and an opening occurs. This type of lock is easy to open, so if security is important to you, then great option take a closer look at another option;
2. Fixed. A simple device with no moving parts. The role of such handles is decorative and they are perfect for internal doors, as seen in the photo;
3. Rotary. This is like a push-button model, which is very often used for the bathroom.

Important Steps

Before proceeding with dismantling the handle, install its structure. It can be the most ordinary or with a snap mechanism. The former, for their part, are also divided into several options:

• secured on both sides with screws;
• having a core going through the entire panel.

1. If pen fixed on ordinary self-tapping screws, you can use a screwdriver. Having removed it, you can easily understand what caused the damage and whether it can be fixed;
2. You will need to tinker with the handle and rod. Try to spin the part while holding the second part of the part to prevent it from spinning. Having removed the part from one side, you can easily remove the second and take out the rod;
3. To remove the handle with the latch, you need to free yourself from the screws holding the fittings, after which you will see how it is secured. Very often, a design of this type has a rod and a tongue movement structure. Remove the not very large rod with the cap and it can be easily removed.

Round designs

Start the process of removing the handle from the side where the locking key is not present:

• First, get rid of the decorative trim by pressing the stopper with a screwdriver and it will easily come off, as shown in the video;
• Unscrew the two screws that hold the parts of the handle and remove them;
• Now you can unscrew the screws holding the latch and remove it.

Between the doors

If the problem is serious, then there is no need to save money and buy a new one. Let's start the replacement process:

• Remove the fittings, taking into account its design and the rules described above;
• Clean the removed handle using sandpaper and you can take it to the supermarket, where they will help you choose a similar model;
• Very often, handles with latches and a lock are purchased for replacement.

Front door

It is very important to determine the breakdown, and then change the handle to input doors. To do this, listen to our recommendations:

1. Using a screwdriver, remove the structure. To do this, unscrew the screws holding the lever on both sides of the door leaf, without touching the internal lock;
2. You need to take an adjustable open-end wrench that will help you unscrew the device or lever. Continue twisting until you remove the rotary type mechanism as shown in the photo;
3. Having taken out the handle, you can easily remove the spring and rotation mechanism.
4. Look at all the details with great attention; the hard work depends on them. If for example pen is loosened, then you can easily notice all these details without even taking it apart;
5. You need to unscrew the retaining ring that holds the torsion spring and washer together;
6. If you did everything correctly, you can easily remove the upper washer located under the retaining ring;
7. The cause of the problem may be the torsion spring. To check this, take it out and look at it carefully. If this is actually the reason, then buy a new one and replace it;
8. The torsion spring should also be checked. To do this, unscrew it with a screwdriver. If it unscrews with great difficulty, then this is excellent and indicates that it is quite tight and there is no need to change it.

Let's sum it up

Replacing the handle is necessary in both cases: a problem and installing a new one doors. If you listen to our recommendations, then in none of the cases will you have any problems. The main thing is to be careful and take your time, and you will definitely succeed.

Many women who glue their eyelashes are interested in the question, and then how to remove the bunches of eyelashes? Of course, you shouldn’t pull out these bunches of eyelashes with all your might, because... you can thus damage your natural eyelashes.

Removing these bundles is very simple, since the glue used for fastening easily dissolves in water. But, in order not to harm your eyes and spoil your eyelashes, it’s better to first do steam bath . To do this, place cotton balls soaked in cool water on your eyes and leave for a while. During this procedure, the glue will soften and can be easily removed.

Next, you should use a cream or other cosmetic product (the main thing is that it has a high fat content) to remove makeup; after applying it to the eyes, you need to carefully and carefully begin to remove the tufts of eyelashes. Never use nail polish remover to remove eyelashes. Based on how the hairs were glued - in bunches or pieces - it will depend on how they need to be removed (in a bunch or one at a time). It would be good to do this with tweezers and, with this process, there is no need to rush, so as not to accidentally damage your natural eyelashes.

On your eyelids, after the procedure, you should apply makeup remover again, remove the remaining glue and apply a special eyelid cream. Fake eyelashes can be used several times in the future if you put them in a storage container. Don't forget that our eyelashes have unique property self-renewal, which occurs constantly every 3 weeks. To strengthen and nourish them, many girls use burdock oil.

After removing false eyelashes, a protective mask will not harm your natural ones. You can use castor, burdock, almond oil, wheat germ oil and other oils for this.

If you have no idea how to properly remove eyelash bundles at home, then it is better to visit a specialist in any beauty salon.

Nowadays, almost any interior door is equipped with such a thing as a door handle. Moreover we're talking about not about an ordinary handle, for example, a round one, which you can simply grab, but about a mechanism that allows you to open and close the door and, if necessary, keep it in the closed position, despite the efforts made to open it. Such a mechanism is, for example, a latch with a lock. With use, door hardware wears out and any handle simply breaks.

Today we will talk about how to disassemble and dismantle it.

Features of various designs

First, let's talk about the designs of door handles and their features.

• The first category we will look at is – stationary models . These are the most common solutions for interior doors. Such fittings are now practically not used. Perhaps on doors installed back in the days Soviet Union, which have not been modernized since then. And it is usually not used in residential premises. Outwardly it looks like a bracket. There are two varieties of this model. The difference between them is that they can be one-way or end-to-end.

If we talk about the latter, then long screws are used to fix 2 handles, which are placed with different sides door leaves - one against the other.

This type of handle can be removed very easily - just unscrew the bolts that hold this structure in place. Such fittings can literally be called cheap, since they have a minimal price. And it’s pointless to repair it, because it can’t be understood.

• The next option is push design. This design decision will be a little more complicated. The handle is a product lever type: the working elements, thanks to the axis, are connected to the lock mechanism. Some options of this type are additionally equipped with a latch that locks the locking part.

Such a handle can be dismantled using a screwdriver with a narrow blade. By the way, such a handle can have a lock with a metal core.

• Another design worth mentioning is rotary model . It has a lot of differences from the above options, which are in the form and design features. General principle work the same as other models.
• The next option for the devices under consideration for an interior door is handle with rosette. Such handles have a round shape and, depending on the design, can be disassembled using different algorithms. They also differ in the method of securing the decorative element. The spherical shape is very convenient to use. Such models are also called knobs.

In general, as you can see, there are a large number of door handles for interior doors. Each type has its own advantages and disadvantages, at the same time, the algorithm for disassembling them will be approximately the same.

Required Tools

To disassemble the door handle, you will need to have a certain tool on hand. Regardless of its type, there may be some hidden elements and parts in it that cannot always be pulled out using conventional tools.

For this reason, you should have the following list of tools on hand:

• hammer;
• screwdriver;
• drill and set of drills with a crown;
• pencil;
• awl;
• square

How to disassemble and remove?

Removing a door handle is quite simple if you have the above-mentioned tools, as well as a little theoretical knowledge of the structure of this mechanism.

To do this, you must follow these steps.

• Support and secure the door well so that it is in a stationary position.
• Now you need to pry the flange decorative type and pull him back a little. Underneath there are fasteners that need to be unscrewed.
• On the mentioned flange of the pressure part there is a special pin, which is locking and spring-loaded. It should be pressed in using a screwdriver. In rotary versions it is usually located in the housing. To get there, you need to insert a key or an awl. If you cannot feel it, then you should rotate the flange until it comes into contact with the pin.

• Now you should press the pin and at the same moment pull out the handle structure.
• Now unscrew the fastening bolts.
• We separate the inside of the element from the outside, take out the handle and the decorative flange.
• If there is a need to remove the latch for replacement or repair, then you should unscrew the screws that secure it to the side of the door block, then remove the bar, and then the mechanism itself.

When installing fittings to a different position, it is better not to disassemble it into spare parts. It attaches easily to door design, but in reverse order.

Now we’ll tell you directly about the disassembly of each category of handles.

• Let's start with the stationary, which does not have a push set, and is also not equipped with a mortise lock. In order to unscrew such a handle, you will need a Phillips or flat-head screwdriver. Alternatively, you can use a screwdriver. Dismantling must begin by loosening the screws that secure the mechanism.

If there decorative elements, then they must first be removed. As you unscrew the bolts, you should hold the counter parts on the back side of the blade. If this is not done, the structure may simply fall out of the canvas and become deformed.

It should be noted that the fastening can be one- or two-sided; accordingly, the structure can be disassembled in different ways, which means that this must be taken care of in advance. When all the bolts are unscrewed, you need to carefully remove the handle from the door leaf using a flat-tip screwdriver. In place old pen a different mechanism is installed or the same design is installed, but with new spare parts.

• If you lead we are talking about disassembling a round handle with a rosette, then it is necessary to clarify that the word “socket” is usually understood as a mechanism that allows you to lock the lock using a small key on one side, which is not used on the other side. There is a special lamb on the second side. In this situation, disassembling the mechanism will be carried out according to the following algorithm:
  1. first loosen the screws that hold the linings that perform a decorative function on both sides;
  2. the screws connecting the mechanism on both sides are unscrewed;
  3. the handle structure is pulled out and the remaining part is removed;
  4. The locking mechanism is pulled out.

If the handle requires repair or any part of it needs to be replaced, then it should be completely disassembled. individual elements and determine the cause of the problem. It is necessary to especially carefully monitor the safety of all small structural elements, otherwise if they are lost, it will simply not be possible to put the mechanism back together.

• Now Let's talk about disassembling the round knob handle. To dismantle this element The following actions are usually performed from the door leaf.
  1. The fastening bolts on one side of the door are unscrewed.
  2. The mechanism is dismantled through special holes.
  3. The additional strip is being disassembled response type. To dismantle this element, simply pull it in your direction.

The non-removable round handle is fixed using the simplest screws for fastening. This mechanism is made with the expectation that later no repair work will be carried out, but a new spare part will simply be purchased, which will take the place of the old handle.

• Push options. Usually they are used instead of rotary solutions. This is due to the fact that they are durable and very easy to use and repair. Disassembly is performed as follows:
  1. first, the screws holding the decorative cloth of the overhead type, which performs the function of a clamp, are unscrewed;
  2. after this careful removal of the overhead sheets located on both sides;
  3. the fastening bolts are unscrewed and pulled out structural elements round shape located on both sides of the door leaf;
  4. All that remains is to open the strike plate and the lock itself, and then pull them out of the fitting grooves.

How to fix it?

Door handle repairs are often carried out in the following situations:

• the handle sticks and is difficult to turn;
• the handle does not return to its normal position after pressing;
• the handle falls out, but the base is not damaged;
• The tongue does not move when pressed.