Finishing panels for the facade of a house with a stone look. Pros and cons of stone-look facade panels. How to install facade slabs under stone

Once faced with the need to decorate the facade of my own house, and having at the same time an extremely limited budget, I decided to consult with friends who had already gone through this. Imagine my surprise when three out of five respondents recommended one well-known resource.

From the very beginning, I considered only facade siding as a finishing material; it looks, of course, banal, but I didn’t count on more with my finances.

I went to see it, and to be honest, I was amazed, but first things first.

Types of facade panels

It turns out that siding is not only straight stripes on the walls of a house, but also a whole catalog of various imitations.

• Tree.
• Wild stone.
• Brick.
• Granite.
• Marble.

I especially liked the stone-look plastic panels. I, as a non-specialist, did not even immediately determine that this was an imitation.

Cladding a house with natural stone has always been a pipe dream, but its price sometimes exceeded the cost of the house itself. Having walked around the vastness of the sites, I discovered several very important points for myself, after which there was no doubt about the choice.

• Appearance. It is possible to distinguish façade panels from natural stone only upon closer examination.
• Acceptable price. Compared to other types of finishing, stone-look facade panels turned out to be several times cheaper.
• Easy installation. After looking at the installation instructions on the website, I realized that I could do it myself.
• Durability. The production of facade panels from hard vinyl implies their service life of at least 30 years. When used in the harshest climatic conditions.

I found a calculator from dom sidinga, did some simple calculations, and it turned out that the final cost was even lower than what I had originally planned. And it’s not just the cheapness of the material, the price was significantly affected by the fact that I will be doing the installation myself, and the fact that it turns out that I don’t have to put insulation under the façade panels!!!

There are two types of facade panels:

1. Single layer.
2. Multilayer.

The first option, of course, is cheaper, but it requires the installation of insulation, and the production of multilayer facade panels implies the presence of a layer of polyurethane, which acts as heat and sound insulation.

Having compared all the pros and cons, I highlighted the beneficial advantages of multilayer panels:

• When finishing with your own hands, they do not require laying additional layers of heat, hydro and sound insulation;
• Installation is possible at any time of the year and at any temperature;
• Completely insensitive to moisture;
• The higher density of facade panels almost completely eliminates temperature deformation;
• The polyurethane layer can withstand a large number of freezing and defrosting cycles.

In a word, there is no doubt left. I refused the services of builders, since I still decided to do everything myself, so I simply ordered delivery of everything I needed on the Internet, and started work the very next day.

Features of facade panels and installation

I was pleasantly surprised by the fact that to install plastic facade panels with your own hands, you do not need any special tools; almost everyone has everything they need at home:

1. Roulette
2. A hacksaw, preferably with a fine tooth, for cutting siding
3. Drill with impact mechanism. And if the house is wooden, then without it
4. Screwdriver. (you can get by with a drill)
5. Building level

First of all, it is necessary to treat the walls with soil, which will protect them from fungus. Next, we make a sheathing that will hold the siding on. At first, in order to save money, I wanted to put a wooden beam on the sheathing, but the specialists from the site explained that there is practically no difference in price between the timber and the metal profile, since wood requires additional treatment with impregnations.

First, using a drill, we attach the holders that will fix the profile to the wall; it is important that they are positioned strictly along the vertical line over the entire height.

Advice: at the stage of lathing production, you need to check the level as often as possible, since crookedly installed guides will create a lot of problems during finishing.

The distance between the guide profiles should be 30-50 cm, and the step between the holders should be up to 1 m.

The guides can be mounted at a very minimal distance from the wall, since multilayer facade panels do not require insulation; the distance is only necessary for free air flow.

The next stage of production is the actual installation of the façade panels. Even before I decided to do the finishing of the facade with my own hands, I was convinced that the panels were attached first, and then the decorative plastic corners and everything else were attached to them. But after reading the instructions on dom sidinga, I learned that you need to start from the corners and joints of the panels.

Having secured the corner panels with self-tapping screws, we measure the distance between them; if it is more than 3.4 m, then at this distance you need to install an H profile, which connects the two panels in length.

Sometimes, for greater aesthetics of appearance, the H profile is placed exactly in the middle of the house. In this case, you will have to cut each panel to length, and the consumption will increase slightly, but the vertical line will run in the center and will fit well into the overall look.

If everything is ready, we mount the starting panel, it is located at the very bottom and all the rest of the finishing will come from it. In cases where the foundation does not protrude beyond the walls, finishing is carried out from the ground itself. This is not recommended; there is a special siding for the plinth that has more durable characteristics.

Important: the starting panel must be clearly level, since a misalignment of just a few millimeters will greatly affect the finishing stage.

After the starting façade panel has been installed, the simplest step remains - installing the siding. To do this, take the panel and, bringing its edges into the corner and H profile, engage the lock with the starting bar, then fasten the panel with a self-tapping screw into a special oval hole so that the cap is in the middle of the oval.

Important: when tightening the screw, you need to make sure that it does not press the panel. The siding should seem to hang on a self-tapping screw.

In this way, all siding segments are assembled and fixed under the roof with a finishing panel.

The finishing of the house with facade panels is completed, now the room will become much warmer, and the house will take on a new face.

Conclusion

Stone facade panels for a private house

By the way, it took me two days to finish the entire house with my own hands, and this taking into account the fact that I had never dealt with facade panels before. Of course, many will say that natural stone cannot be compared with anything, and I probably agree with this. But often, the question of the price of finishing materials plays a key role in their selection.

Moreover, not everyone can do the finishing with natural stone with their own hands; it requires special skills and a set of tools. There are no such problems with siding, and this puts it a step above its competitors.

The original decoration of the facade of the house with stone-effect panels, the photo of which you see on this page, allows you to obtain a decorative and respectable facade at the lowest cost. In addition, this particular finishing option is characterized by minimal weight, which cannot be compared with the weight of a facade made of natural stone.

If you are considering decorating the facade of your house with stone panels as an option, the photos will help you solve 3 problems:

1. First, choose which texture option. Will it be a wild stone or will it be granite paving stones.
2. Next, you can choose the material of the panels that you will use based on the options. Some panels are made from metal, others from plastic.
3. Having chosen the panel material, you can begin searching for a panel manufacturer that is represented in your city.

Thus, if you are planning to decorate the facade of your house with stone panels, photos of options play an important role at the planning stage, allowing you to save money and save you from purchasing test samples.

Which panels to choose - plastic or metal

The choice of plastic or is, as they say, a matter of taste, as well as the influence of specific local conditions.

For example, modern manufacturers of facade panels offer more color and texture options in plastic. But metal panels are more durable.

It turns out that if your house is located on a relatively large fenced area and it is important for you to give it a more decorative look, you can use plastic panels to look like stone.

If your house faces a roadway or pedestrian street path in a village or city, then you should pay attention to metal panels that imitate. In this case, strength is more important than the decorativeness of the material.

Decorating the facade of a house with stone panels - photo gallery

We also present to you several options for decorating the facade of a house with stone panels. Look at the photos and choose the options that you like best.

After this, decide on the material of the panels, and then you can begin to search for specific color and texture options that are offered by trade organizations near your home.

The starting profile is used to protect the end faces of PVC panels from damage. It is also used for finishing window and door frames, slopes in places adjacent to...

The technology of finishing the base with panels that externally imitate stone originated in Canada and the USA, but is now becoming more widespread due to a lot of advantages. The panels we are talking about in this article are a type of siding and it is easy to guess that they look like stone in appearance. They are produced using high pressure casting.

Despite the fact that sheathing the base with this material is beneficial from many angles, the installation must be carried out very accurately and carefully, however, the same applies to other finishing materials. So, let's look at how the base should be finished with stone panels.

The base is the part of the foundation that is located above the ground. One of the functions that the plinth performs is to protect the building from moisture, including rain. The plinth bears both functional and architectural load, so this part of the house must be treated very responsibly. The plinth also provides thermal insulation between the main space of the building and the basement.

Interesting! Architects believe that the base should be attributed to the wall, its lower part, but builders, on the contrary, are sure that it is still an element of the foundation.

Advantages and relevance of covering the base with stone panels

Firstly, modern materials have excellent design and significantly improve the exterior of the building. Secondly, the technique allows you to increase resistance to moisture, which allows you to forget about problems with foundation cracking for a long time. If liquid gets into the voids of the material from which the base of the building is made, it will freeze in cold weather, and, as you know, ice has a larger volume than water, and cracks will eventually appear. To better understand the principle, you can put a PET bottle filled to the top with water in the freezer overnight - in the morning the container will be greatly deformed. The same thing happens with building materials if moisture gets into them.

The base bears a much greater load than the façade, so this part of the building must be treated with great attention. Temperature changes that cannot be avoided, groundwater flows, the pressure of the house itself, and precipitation in the form of rain or snow can have a bad effect on the condition of the base.

Finishing the base with panels - features of material and fastening

One of the methods that have proven themselves to be excellent in protecting the base is special panels stylized to resemble a stone structure. Among the important positive aspects it is worth highlighting the following.

Base siding "Alta-profile"

Price for decorative stone

Decorative rock

Flaws

It is difficult to find really serious negative aspects of panels for finishing the plinth, but a couple of points can be pointed out.

1. Limitations in color. It will not be possible to choose a shade to suit your taste, since the external appearance of the panel is stylized to resemble stone, which has specific dim colors. But, if you were unable to choose the desired design in store catalogs, you can always contact the manufacturer directly and place an order according to your taste. Whether it is worth paying extra for such a service is up to you to decide.
2. Despite the fact that the panels withstand loads and the influence of many destructive factors very well, Fire resistance cannot be expected. Since the main material of manufacture is still plastic, the panel will quickly melt at elevated temperatures, and therefore it is not worth grilling kebab or burning garbage near the house.

Materials from which stone panels are made for basement finishing

The production of such products is carried out only using new, innovative technologies that emerged thanks to the hard work of highly qualified specialists. Only materials that are highly resistant to low temperatures and are endowed with water-repellent properties are used. Also, they (the materials) should not crack in winter and in strong winds. Most often, polypropylene is used as a basis, which is formed by casting; the characteristics of such panels are always at a high level.

In general, it is possible to use different polymers if they have added chemicals that increase the life of the product. The choice of base material directly affects the cost.

Existing types of panels

Before choosing and purchasing the required number of panels, you need to understand the existing types of these products, with all their features, strengths and weaknesses. Each variety has some differences that need to be taken into account. Today, 4 types are widely used, which are presented in the table.

Table. Popular types of stone-look plinth panels.

What does the cost depend on?

The price will depend on several factors. Firstly, this is the country that produces the siding and the specific company - the more reputable the company, the higher the cost will be. The material used, what polymers, modifiers, etc. are also affected. If you select easy-to-install products that are large in size, then the price for them will be higher than for small options. If you want to save money, then you should not choose elaborate panels, since the intricate texture and multi-colored colors significantly increase the cost. The better the characteristics of the product, that is, resistance to temperature changes, strength, resistance to wind - the more expensive it will cost.

Important! It is worth paying attention to the domestic manufacturer; among the products they present on the market, you can now find very good specimens not only in appearance, but also in characteristics, while the price is an order of magnitude lower than that of foreign analogues.

Prices for popular stone-look finishing wall panels

Stone effect wall panels

Panel selection

When you start choosing stone-style panels for finishing the base, you need to pay special attention to several parameters. If the product is of high quality, then the characteristics specified by the manufacturer will be high, and the appearance should be appropriate, without defects. The material greatly affects the rate of fading under the sun, if the base is not in the shade and you want to preserve the beautiful exterior for a long time - find out more from the seller.

It is better to buy panels in places where there is a large selection of different products, so that you have plenty to choose from. The period of successful operation is also very important: if a company has existed for several years and has accumulated many customers with positive reviews, it means it sells a quality product. Decide what is more important - convenience during installation or savings. If the first, then you should pay attention to large panels, but if the second, then to small ones. A good product must be accompanied by a license and certificate, which guarantee quality.

The facade, lined with Dagestan stone, looks prestigious and creates the impression of wealth of the homeowner. However, the costs of such finishing are relatively small and comparable to the costs of installing a “wet facade”. Therefore, at a relative low cost you can get an impressive result. Read more in .

Panel installation

Installing the panels under the stone is easy. You need to be very careful and pedantic in the process, carefully carry out all measurements and calculations.

We will tell you how to properly install a finishing panel on a concrete base.

Prices for cordless drill/driver

Cordless drill/driver

We will need:

• roulette;
• circular saw with diamond blade;
• perforator;
• fasteners.

Step 1. We calculate the required number of panels in one row. To do this, divide the total length of the wall (minus the space for corner elements) by the useful length of one panel.

Step 2. If there is not enough part to cover the entire length of the wall, or you need to install panels along the contour of a window or other element without covering it, use a tape measure and measure exactly how the panel needs to be cut. Using a hand-held circular saw with a diamond blade or a hacksaw, we cut out the part we need from one panel.

Important! You should not cut off more than 1 part from each product, otherwise the result will not look so natural.

Prices for angle grinders (grinders)

Angle grinders (grinders)

Step 3. Let's move on to installing the panels. We lean the product against the base exactly in the place where it will be located. We need to drill the mounting hole using a hammer drill, after which we use special fasteners for reliable fixation.

Step 4. We move the next panel, fasten it in 6 places so that it is resistant to the wind - 5 fasteners on top and 1 on the side. The top line of fastening should start from the center.

Step 5. We make sure that the mount is not too rigid to ensure proper response to temperature changes (expansion compensation).

Important! Gaps are also needed between the panels for the same purpose. If you are installing in winter, then the joint width should be about 15 cm, and if in summer, then no more than 10 cm.

Video - Installation of plinth panels

As you can see, the installation process is not at all complicated and does not take much time; at the same time, your house will be insulated, and the base will be strengthened and protected from moisture. The technology makes it possible to simply and cheaply add elegance to the exterior and increase the life of the building.

After construction, the house cannot be left in this condition. Exterior wall finishing will be required. It is designed not only to improve appearance, but also to provide some protective functions. Cladding with natural stone is very expensive, but the appearance will be stunning.

There is another solution that will cost much less, but it is unlikely that anyone will be able to see the catch. It is carried out with the help of decorative ones. Which ones are best to choose and why are they good? The article is devoted to discussing these points.

Why are they good?

Finishing a facade with natural stone can take not just days, but whole months. This is due to some complexity of the technology and the selection of required components. If we talk about panels, the whole process happens very quickly. This is due to the modular design of the panels. When installing such decorative panels there are no special requirements for weather conditions. Rather, we are talking about the comfort of the master himself.

Some types of natural stone only require dry, warm weather. Otherwise, it will simply fall off over time. Trimming the panels occurs without a lot of dust. This number will not work with natural stone. Cleaning up after it's installed makes up a good amount of time. Some types of panels do not require the use of glue.

With regard to decorative panels, there are no special requirements for the condition of the wall of the house and what it is made of. Often panels are made of polymer materials. They are light in weight, which means they will not put a load on both the walls themselves and the foundation. Cutting corners is a pleasure. Typically, the manufacturer provides additional modules for panels that do not require scrupulous routing of corners. Another advantage of some decorative panels is the additional sound insulation they provide to those living in the house.

Requirements for panels

Although many are guided solely by appearance when choosing a material for finishing, this is not its only purpose. Another factor is what protective properties the panels have. They must be able to compensate for sudden temperature fluctuations, as well as provide protection against moisture penetration. This is especially true for structures that are assembled using a frame method, made of wood or other hygroscopic material. Another important point that can be decisive when choosing panels for exterior decoration is how they will behave when exposed to open fire. Some products are made using insulating lining material, which can instantly catch fire.

It would be unpleasant if after some time the color of the panels faded or completely faded. That is why they must be resistant to ultraviolet rays. Such products do not require special maintenance and can be easily cleaned with water. The modules must be fixed in such a way that the surface of the walls can be freely ventilated. This will make it possible to prevent the formation of condensation and the growth of fungus.

Types of panels

To make the best choice, you need to have a good understanding of what types of decorative panels there are for exterior decoration. The main types of modules with their features will be listed below.

Under the brick

Many luxury houses today are decorated with decorative brick. He looks simply wonderful. But many are stopped by the figure that is obtained after calculations only for the purchase of material. If you take into account delivery, additional materials and the services of a master, then it just becomes bad. The solution is to use finishing panels that have a pattern that is almost impossible to distinguish from real brick. This can only be done with a very close examination, and sometimes only tactilely. The cost of such panels is several times cheaper. In terms of their quality characteristics, modules for facing bricks are practically not inferior.

This fairly large group is divided into two main subspecies. One of them implies the presence of modules with a homogeneous structure, and the other - with a combined one. The difference concerns the layers of the cake from which the modules are made. The additional structure implies the presence of fixed insulation, which eliminates the need for additional purchase. If the house is already insulated using polystyrene foam or penoplex, then modules with a homogeneous structure are suitable, which can simply be mounted on top of the insulation. Some types of modules with insulation are fixed using the hot method without the use of classical glue or solutions.

Facade modules for external finishing with a brick pattern significantly reduce cladding time. Bricks must be laid in rows, and one module already has several rows. The material from which they are made easily withstands even harsh winters. Some types of bricks accumulate salt from rainwater over time, which appears as white spots. As a rule, it is quite difficult or impossible to wash them. There is no such problem with finishing modules. Many people opt for combined panels, since two tasks are performed at once. An example of the installation of such modules can be seen in the video below.

Advice! Facade modules that are designed to look like brick can be used not only for wall decoration. Some people buy them for fences or other buildings. They perform their function just as well as on the building.

Under the stone

It is difficult to find a person who would not like natural stone finishing. The “savage” stone has gained great popularity. It does not require any maintenance and is ready to last for centuries. But it all comes down to cost again. Natural stone panels are similar in structure to those made to resemble facing bricks. They can also be with or without insulation. The front side is most often made of polymer materials.

The cladding modules do not lose their color in the sun and do not crack in the cold. Installation of such external cladding panels can be done in two ways. The first of them involves the use of a special sheathing that is attached to the wall. And the second is direct contact with the wall through glue. The latter is more suitable when the walls are ideal. If they need to be leveled a little, then it is better to attach them to the sheathing.

Note! Stone facing modules often have a non-standard and irregular shape. This is an important factor that allows you to achieve maximum consistency with natural stone.

The price for such finishing panels is quite affordable. Its formation can be influenced by the size of the module, its shape, thickness, and color. Installation work does not require ideal weather conditions. Basic construction skills are usually enough to do the job yourself. They can be used both for finishing the plane of the walls and the basement level.

Under clinker tiles

Clinker tiles have already become a favorite among many owners. She has a pleasant appearance. Most often it is made with soft colors without variegated inclusions. It allows you to create a calm atmosphere. The tiles have good heat retention properties. The finished product tolerates sudden changes in temperature well. In addition, it is quite durable. It does not lose its properties when used on panels for finishing facades. The method of making such panels is very interesting. The tiles are laid out on a special base and filled with insulation, which then acquires the required parameters.

The panels turn out to be environmentally friendly, because the insulation itself does not have harmful emissions, and the tiles are made of natural clay, without foreign impurities. The sun's rays cannot dull the color of the tile. Cladding panels also withstand physical impact very well. The price of such modules is slightly higher than other options. This is explained by the cost of the clinker tiles themselves, since they are a natural component. Even with high humidity, fungus and mold do not appear on such panels. There are practically no pores in the tile, so it does not absorb moisture.

Another name for facing modules made of clinker tiles is thermal panels. This is due to the use of one of the best insulation materials. Its quality is not penoplex, but polyurethane foam. The latter does not ignite in an open fire; it can melt, but nothing more. Installation of such panels can be done by attaching them to the sheathing or directly to the walls. Thanks to the clear lines on such finishing modules, it is very easy to maintain a given level and carry out installation yourself. Cladding panels with clinker tiles may not necessarily be smooth. Some types of tiles that are used for cladding modules have some relief.

Note! Although clinker tiles are resistant to physical impacts, they can burst and crumble from strong impacts. This should be taken into account when choosing places to attach such cladding. If one tile is damaged, the entire panel will lose its appearance.

Before installing cladding panels with clinker tiles, it is necessary to take care of high-quality surface preparation. The walls must be plastered and treated with an antiseptic compound. If there is old paint on them, it must be removed. There is always the option of mounting on a frame, which will simplify the task. Such facing panels are ready to serve for decades. At the same time, they will always look like new.

Fiber cement

From the name it becomes clear that such cladding panels are made of cement with the addition of certain fibers. Most of the mortar for production is plaster. It is mixed with special granules that control the moisture content of the material itself. The protective layer is located on both sides of such a cladding panel. It is quite durable, so it is designed to last a long time. Sudden temperature changes do not affect the shape of fiber cement panels. Such panels for exterior decoration are quite stable. Their advantage is fire resistance.

Such decorative panels for exterior decoration can be made to look like stone. They do not have harmful secretions, which is important for those families with children. A wide variety of pigments can be added to the cladding modules, creating unique color solutions. They can also be painted. But you will have to pay a hefty sum for paint for such facing panels. The price is influenced not only by the color, but also by the design implemented on them. The thickness may also be different, which will affect the cost of panels for exterior decoration. Some versions of cladding modules have special brackets, which makes their installation easier. The composition formula for the production of panels is kept secret by each manufacturer.

Note! Care should be taken when choosing these cladding panels for areas that experience frequent rain or high humidity. Modules may become slightly deformed under such conditions.

Conclusion

As you can see, modules for cladding a house are a very beneficial solution from both an aesthetic and practical point of view. If you install another row of insulation under the panels with insulation, then in the cold season you will have to spend less money on heating. Finishing panels can be combined. For example, the main plane of the wall can be made using one type of modules, and the basement floor can be faced with another.

During the construction of sheathing for decorative modules, experts advise observing the required spacing of the planks. This will protect the modules from damage due to pushing. Some types of cladding are attached not from the modules themselves, but from corner strips and other additional elements. Usually the manufacturer indicates this in the instructions for a specific product.

Today we will talk about one very interesting finishing technology that is used for decorative design of facades. This is the cladding of a house with stone panels. It is interesting because the panels themselves, although they are not stone, are indistinguishable from masonry in appearance. You will learn about the varieties of this finishing material and the technology for installing it on the facades of houses. The information will be useful to those who are planning to use this material for cladding their own home. It will give you the opportunity to understand what and how the craftsmen who have been entrusted with this responsible work do.

House lined with plastic facade panels to look like stone

What are the panels

Facade panels for exterior finishing of a house to look like stone belong to the siding category. Accordingly, the method of their installation is fastening to the sheathing (frame), which itself is attached to the facade of the building. That is, no wet processes associated with cement or adhesive solutions. This is the main distinguishing feature of the panels from the same stone, tiles, clinker and other facing materials.

More recently, this material was called basement siding, because the original purpose of its production was to produce products that could be used to cover the basement part of the foundation (protruding above the ground). Over time, it turned out that the possibilities of basement siding are much wider. One of the craftsmen simply tried to lay it on the wall, since its decorative properties allowed it to be done. The effect turned out to be unusual and original. And so it went, and the popularity of the material immediately grew exponentially.

Model line of stone-look facade panels

And the reason was the pattern of the panel, which is stone or brickwork. In this case, the stone can be of any kind, because the shapes of the product are formed on standard masonry. That is, they assemble masonry from some natural stone on the floor in a workshop and fill it with a molding mixture that repeats its pattern. After drying, the form is removed and used for its intended purpose. It's the same with brick.

As for the raw material for pouring products, the choice is huge, but acrylic, vinyl or propylene are most often used. Although some manufacturers today offer metal or fiber cement panels. The former belong to the category of cheap materials, the latter are more expensive. But some panels from the first group are not inferior in quality to the second. At the same time, the polymer material exactly repeats the pattern and structure of the stone, so in terms of the degree of realism, even next to the cladding, it is difficult to distinguish it from natural stone finishing.

And if you consider that the price component of the panels is several times less than that of natural and even artificial stone, then it becomes clear where such popularity comes from.

Huge variety of textures and colors

On our website you can familiarize yourself with the most. In the filters you can set the desired direction, the presence of gas, water, electricity and other communications.

Today on the construction market you can purchase panels for cladding the outside of a house to look like stone with imitation of such varieties:

granite;

slate;

stone rubble;

sandstone;

dolomite;

tuff and other rocks.

At the same time, manufacturers offer different color imitation of panel products, which expands the offered range several times more. That is, the model line of façade cladding panels is so wide that familiarization and selection takes a lot of time. And this greatly distinguishes them from traditional siding, which does not have such a rich variety of patterns and colors.

Facade plastic panels with imitation rubble stone

Pros and cons of stone-look facade panels

We have already become familiar with some of the advantages of stone-look panels for the facade of a house, but here is their full list:

huge range in terms of color and texture;

realism simulated stone or brick;

small specific weight, which simplifies the installation process, while the panels do not overload the supporting structures of the building (this advantage does not apply to fiber cement products, they are quite heavy);

acceptable price(again this does not apply to fiber cement and metal products);

cope well with all natural rays, even sunlight, under the negative influence of which they do not change their color and do not warp;

panels don't rot, do not rust, colonies of harmful microorganisms do not take root on them;

simple installation;

long-term exploitation– not less than 50 years;

simplicity maintenance - just occasionally water it with a hose under low pressure.

On our website you can get acquainted with the most popular house designs for the finishing of which stone panels, natural and artificial stone were used - from construction companies presented at the exhibition of houses "Low-Rise Country".

And literally two lack:

plastic panels become brittle at low temperatures;

when it gets very hot in summer it appears extension products, so it is important to follow the installation instructions exactly and not forget some of the nuances of the installation process.

Used for cladding both plinth and walls

Dimensions and specifications

It should be noted that depending on the raw material, both characteristics and dimensional parameters will differ.

The length of plastic facade panels varies in the range of 1-1.25 m. But on the market there are cladding elements up to 6 m. The standard width is in the range of 26-45 cm. The latter is more common. Thickness - 1-1.2 mm, for fiber cement from 6 to 12 mm. There are plastic ones with an insulating layer of up to 30 mm.

As for the technical characteristics, the main one is the operating temperature, which ranges from -40C to +60C. All other characteristics, such as strength, moisture resistance, heat resistance and fire resistance, depend on the material from which the panels are made.

Dimensional parameters of facade panels of the “Yantar” model

Installation technology

So, having figured out the material for cladding the outside of the house with stone, we move on to the method of installing it on the facade of the building.

On our website you can find contacts of construction companies that offer insulation and finishing services for houses, and use materials of their own production for this. You can communicate directly with representatives by visiting the “Low-Rise Country” exhibition of houses.

Frame installation

It should be noted that some manufacturers offer panels for facade cladding with sheathing elements included. This is convenient because there is no need to select material for the frame separately. Although the elements themselves are metal profiles. Therefore, if the lathing is not included in the delivery package, then profiles for installing drywall or wooden blocks with a maximum cross-section of 50x50 mm are used as its elements. Let us immediately note that metal guides are preferred. They do not change their linear dimensions under the influence of changing humidity and temperature. The same cannot be said about wooden blocks.

It is necessary to make a reservation that not all panels with imitation stone are attached to the sheathing. Some of the models are attached to the wall of the house if it is well leveled, or if Penoplex-type slab insulation is laid on top of it. This facing material already has mounting holes and The installation steps are as follows:

panels apply at the place of attachment;

through holes on the wall notes;

remove panel;

by tags hammer drill make holes into which plastic dowels are driven;

install wall covering material;

screwed its self-tapping screws.

Video description

To help you understand how this all happens, watch the video:

But in this article we are mainly interested in the lathing installation method. Therefore, first of all, its elements are mounted on the facade of the house. To do this, first mark the installation sites of galvanized profiles. Be sure to use it near window and door openings, as well as at the edges of the wall. All other guides are installed in increments of 50-60 cm. By the way, the installation direction is vertical.

Along the designated lines mount straight hangers with a pitch of 50-60 cm. They are attached to the wall with self-tapping screws on plastic dowels.

Install thermal insulation layer. More often these are polystyrene foam boards or mineral wool in mats. The insulation is directly placed on straight hangers.

Stacked vapor barrier from a diffusion membrane. It is laid in strips with overlapping edges within 10-15 cm and covered with self-adhesive tape.

Install to the hangers guide profiles, they are attached to them with self-tapping screws. The main task of the work manufacturer is to align all profiles in a single vertical plane.

Lathing for facade panels assembled

Installation and fastening of facade panels

The installation process begins from the corner of the building, usually from the left. The panels are assembled in order. Mounting method:

for plastic models – self-tapping screws;

for fiber cement – clamps.

In the first case, mounting holes have already been made directly in the facing material. They are in the form of grooves, which makes it possible to regulate the precise joining of adjacent elements to each other.

Fiber cement panels secured to the frame with clamps

Here is the algorithm for the installation operations:

first installed and secured to the sheathing starting bar, which is strictly set horizontally;

filled in this way first row cladding, at the end a corner element must be mounted.

It is very important to set this particular row horizontally. Next, the remaining rows are assembled in exactly the same sequence to the top edge of the wall. Please note that in the vertical direction, the cladding elements are assembled using a tongue-and-groove joint, which ensures complete parallelism of the rows with each other and 100% tightness of the joint, which is very important for façade materials. The edges of the top row are covered with the so-called J-bar. Essentially, this is a finishing strip that gives the end a complete design.

Correct assembly of façade cladding

An important step in decorating the outside of houses with stone is lining areas near openings (windows and doors). Cladding panels made of plastic or cement are a material that can be easily processed. Cutting it to the required size is not a problem. To do this, use a grinder or a stationary cutting machine. Therefore, panels are laid around the openings and trimmed to the required size (height or length). The installation itself is carried out using standard technology. After completion of the work, the open ends are covered with special corners or slopes, which complete the decorative design of the building facade.

Video description

How to install façade panels from the manufacturer Döcke-R, see the following video:

Video description

And in this video, examples of finishing houses with artificial stone:

Conclusion on the topic

Stone panel cladding of a house is one of the effective ways to give a building a presentable, solid and unusual appearance that stands out from everything that construction companies can offer today. Let us add that this type of cladding is an inexpensive pleasure, but with a fairly long service life. That is, in almost many respects it is superior to other materials and technologies.