Floor-standing cast iron gas boilers Buderus Logano G234. Floor-standing cast iron gas boilers Buderus Logano G234 Gas boiler buderus g234 ws

Article: 8732204652

Documentation

Logano G234 WS

• Boiler block design with perfectly matched sections
• Boiler sections made of high quality cast iron GL 180 M
• Combustion chamber closed on all sides
• Intensive heat transfer of heating surfaces thanks to special fins
• Easy installation and maintenance thanks to simple design
• Fully automatic operation with electric ignition, no additional gas consumption required for ignition
• To make it easy to connect gas to the boiler at the back, there is a gas pipeline under its casing.
• Thermal insulation 80 mm thick. reduces heat loss to a minimum
• The heating boiler is completely assembled together with the casing - this saves time and installation costs
• Compact dimensions - an advantage when carried through openings and when placed in a boiler room
• Various combinations with control systems and cylinders - to suit every need
• Large selection of additional equipment for quick installation, adapted to a specific boiler

• Fully automatic burner with electric ignition
• Ionization flame control and double magnetic valve
• The Venturi tube of a gas burner ensures mixing of fuel with air. During the combustion process, many small individual flames are formed without a high-temperature core. Therefore, in such gas burners the combustion temperature is significantly reduced. In addition, the short flame of these fireplaces easily breaks away from the burner rod, reducing the heat load on it

• Heating boiler - for operation on natural gas H, with thermal insulation and boiler casing - 1 box
• Conversion kit for liquefied gas P and B/P (additional equipment) - 1 box
• Control system (optional) - 1 box

Hydraulic resistance of the boiler through water

Fuel

The gas burners are factory set for natural gas H, comparable to the EE-H method. You can change the gas type to liquefied P/B/P at any time using the conversion parts. Conversion to city gas is not possible. The supplied gas pressure (supplied pressure is the static excess pressure of the gas relative to atmospheric pressure when it flows out at the connection point of the gas appliance) must be in the following range:

1) - Up to 8 mbar when working with a gas pressure monitoring device

The maximum supply pressure when operating on natural gas can be 25 mbar. If the supplied gas pressure is higher, it is necessary to install an additional gas pressure regulator on the burner. The maximum test pressure is 150 mbar.

Flue gas temperature / chimney connection

The required pressure is for all boiler sizes a minimum of 3 and a maximum of 10 Pa.
For more precise adjustment and maintenance of draft in the chimney, as well as for organizing ventilation of the chimney itself, it is recommended to install and adjust an additional air regulator (draft limiter). The cross-section of the additional air regulator depends on the effective height and cross-section of the chimney.

Flue gas shut-off valve

If desired, a flue gas shut-off valve can be purchased as an optional extra. A flue gas shut-off valve installed before the draft breaker is more effective than one installed after it.

Installations with underfloor heating

In floor heating systems using oxygen-permeable plastic pipes (DIN 4726), it is necessary to install a heat exchanger between the heating boiler and the floor heating system.

Preparing hot water

The heating boiler can work with any water heater tank. Combinations of the boiler with tanks of the Logalux ST/SU series have particular advantages.

General provisions

• For heating boilers that must be equipped with a flue gas monitoring system according to the FeuVO of the relevant federal state, accessories can be supplied
• For version B11 (without flue gas monitoring system), the boiler may only be installed in rooms that have the required ventilation to the atmosphere and also have a self-closing and sealed door, for example in boiler rooms
• For version B11 BS (with flue gas monitoring system), the heating boiler can be installed in apartments or similar places
• To ensure the functioning of the boiler, all connections must be made in the places specified for them
• When installing a gas heating boiler operating on liquefied gas below ground level, it is recommended to install a second solenoid valve. A switchgear for controlling the solenoid valve can be supplied as an option
• In installations with underfloor heating, with several heating circuits, as well as in installations with large water volumes, it is necessary to install a mixer to regulate the heating circuits, depending on local operating conditions.

To ensure environmentally friendly and trouble-free operation, we recommend regular inspections of the boiler and burner.

Boiler installation room

When installing the heating boiler, the minimum distances shown (indicated in parentheses) must be observed. For ease of installation, servicing and maintenance, it is necessary to maintain the recommended distances from the walls.

The room for installing equipment must be protected from the cold and have good ventilation. In addition, care must be taken to ensure that the combustion air is not contaminated with dust or halogenated hydrocarbons. Halogenated hydrocarbons of all types are found, for example, in aerosol cans, solvents and cleaners, varnishes, paints and adhesives.

Modern universal boiler concept

• Low temperature heating boiler according to DIN EN 297 with continuously variable boiler water temperature control without base temperature (minimum boiler water temperature)
• Four certified boiler sizes with a nominal heating output of 38-55 kW
• The heating boiler is designed to operate on natural gas H and liquefied gas P / B/P
• Boiler design with perfectly fitted sections made of high-quality cast iron
• Tested and reliable heating boiler with cast iron heat exchanger and atmospheric gas burner
• Combines with adjacent Logalux ST and Logalux SU water heater tanks from the Buderus program
• Can be combined with various control systems from the Buderus program
• High standardized utilization rate (93%) and low emissions of harmful substances

• Atmospheric gas burner with pre-mixing without fan
• Heating mode without additional noise reduction measures
• Stable operation on natural gas with supply pressure up to 10 mbar

• Control functions coordinated with the plant hydraulics
• Easy setup of all control system functions (Push and Turn principle)
• It is possible to expand the configuration of all control systems for additional modules

• A system for quickly installing the heating circuit, adapted to the corresponding hydraulic circuit, for connecting it to the boiler or mounting it to the wall
• Convenient connection of Logalux ST and Logalux SU water heater tanks with a capacity of 150, 160, 200 and 300 liters to the boiler thanks to the boiler-water heater connecting pipeline with loading pump and check valve
• Burner design without moving parts
• Easy conversion of the burner to other types of gas

Floor-standing cast iron boilers Logano G234 and Logano G234WS are equipped with an atmospheric pre-mixing gas burner. They can be easily combined with many water heaters and control systems from the Buderus program.

Power for any task:

Adapted for operation in Russian gas networks, Buderus Logano G234 boilers 38 kW, 60 kW, 44 kW, 50 kW, 55 kW have a performance that can cope with the most complex tasks. In combination with high-quality water heaters and convenient automation systems, they can not only warm any object, but also provide it with hot water.

Low temperature mode for maximum efficiency:

Low-temperature technology is very economical, but places serious demands on materials. At low temperatures, condensation may form briefly on the surfaces of the boiler, which causes corrosion, therefore Logano G234 heating units are made of special high-quality gray cast iron, resistant to aggressive influences.

The atmospheric gas burner integrated into the Logano G234 does not require a fan, so it is characterized by low noise. In addition, this type of burner device has low emissions of harmful substances. When burning natural and liquefied gas, the maximum result is always achieved.

Article: 8732204655

Documentation

Logano G234

• Boiler block design with perfectly matched sections
• Boiler sections made of high quality cast iron GL 180 M
• Combustion chamber closed on all sides
• Intensive heat transfer of heating surfaces thanks to special fins
• Easy installation and maintenance thanks to simple design
• Fully automatic operation with electric ignition, no additional gas consumption required for ignition
• To make it easy to connect gas to the boiler at the back, there is a gas pipeline under its casing.
• 80 mm thick thermal insulation reduces heat loss to a minimum
• The heating boiler is completely assembled together with the casing - this saves time and installation costs
• Compact dimensions - an advantage when carried through openings and when placed in a boiler room
• Various combinations with control systems and cylinders - to suit every need
• Large selection of additional equipment for quick installation, adapted to a specific boiler

• Fully automatic burner with electric ignition
• Ionization flame control and double magnetic valve
• New combustion system reduces emissions of harmful substances
• The Venturi tube of a gas burner ensures almost 100% mixing of fuel with air. During the combustion process, many small individual flames are formed without a high-temperature core. Therefore, in such gas burners the combustion temperature is significantly reduced. In addition, the short flame of these fireplaces easily breaks away from the burner rod, reducing the heat load on it

• Heating boiler - for operation on natural gas E (G 20), with thermal insulation and boiler casing - 1 box
• Parts for conversion to liquefied gas P (G31) (optional) - 1 box
• Control system (optional) - 1 box

Hydraulic resistance of the boiler through water

Fuel

The gas burners are factory set, comparable to the EE-H method, for natural gas E (G20). You can change the gas type to liquefied P (G31) at any time using the conversion parts (optional). Conversion to city gas is not possible. The supplied gas pressure (supplied pressure is the static excess pressure of the gas relative to atmospheric pressure when it flows out at the connection point of the gas appliance) must be in the following range:

The maximum supply pressure when operating on natural gas can be 25 mbar. If the supplied gas pressure is higher, it is necessary to install an additional gas pressure regulator on the burner. The maximum test pressure is 150 mbar.

Flue gas temperature / chimney connection

The required pressure is for all boiler sizes a minimum of 3 and a maximum of 10 Pa.
For more precise adjustment and maintenance of draft in the chimney, as well as for organizing ventilation of the chimney itself, it is recommended - after consultation with an authorized chimney specialist - to install and adjust an additional air regulator (draft limiter). The cross-section of the additional air regulator depends on the effective height and cross-section of the chimney.

Flue gas shut-off valve

If desired, a flue gas shut-off valve can be purchased as an optional extra. A flue gas shut-off valve installed before the draft breaker is more effective than one installed after it.

Installations with underfloor heating

In floor heating systems using oxygen-permeable plastic pipes (DIN 4726), it is necessary to install a heat exchanger between the heating boiler and the floor heating system.

Preparing hot water

The heating boiler can work with any water heater tank. Combinations of the boiler with tanks of the Logalux ST/SU series have particular advantages.

General provisions

• For heating boilers that must be equipped with a flue gas monitoring system according to the FeuVO of the relevant federal state, accessories can be supplied
• For version B11 (without flue gas monitoring system), the boiler may only be installed in rooms that have the required ventilation to the atmosphere and also have a self-closing and sealed door, for example in boiler rooms
• For version B11 BS (with flue gas monitoring system), the heating boiler can be installed in apartments or similar places
• To ensure the functioning of the boiler, all connections must be made in the places specified for them
• When installing a gas heating boiler operating on liquefied gas below ground level, it is recommended to install a second solenoid valve. A switchgear for controlling the solenoid valve can be supplied as an option
• In installations with underfloor heating, with several heating circuits, as well as in installations with large water volumes, it is necessary to install a mixer to regulate the heating circuits, depending on local operating conditions.

To ensure environmentally friendly and trouble-free operation and in accordance with § 10 EnEV, regular inspections of the boiler and burner are recommended.

Boiler installation room

When installing the boiler, the minimum distances shown (indicated in parentheses) must be observed. For ease of installation, servicing and maintenance, it is necessary to maintain the recommended distances from the walls.

The room for installing equipment must be protected from the cold and have good ventilation. In addition, care must be taken to ensure that the combustion air is not contaminated with dust or halogenated hydrocarbons. Halogenated hydrocarbons of all types are found, for example, in aerosol cans, solvents and cleaners, varnishes, paints and adhesives.

Modern universal boiler concept

• Low temperature heating boiler according to DIN EN 297 with continuously variable boiler water temperature control without base temperature (minimum boiler water temperature)
• Options for operation with natural gas E or liquefied gas P
• Boiler design with perfectly fitted sections made of high-quality cast iron
• Tested and reliable heating boiler with cast iron heat exchanger and atmospheric gas burner
• Combines with adjacent Logalux ST and Logalux SU water heater tanks from the Buderus program
• Can be combined with various control systems from the Buderus program
• High standardized utilization rate (93%) and low emissions of harmful substances

• Atmospheric gas burner with pre-mixing without fan
• Heating mode without additional noise reduction measures
• Harmful emissions are below the Blue Angel environmental requirements
• CE mark

• Control functions coordinated with the plant hydraulics
• Easy setup of all control system functions (Push and Turn principle)
• It is possible to expand the configuration of all control systems for additional modules

• A system for quickly installing the heating circuit, adapted to the corresponding hydraulic circuit, for connecting it to the boiler or mounting it to the wall
• Convenient connection of Logalux ST and Logalux SU water heater tanks with a capacity of 150, 160, 200 and 300 liters to the boiler thanks to the boiler-water heater connecting pipeline with loading pump and check valve
• Burner design without moving parts
• Easy conversion of the burner to other types of gas

Buderus Logano G234 WS-50 kW Floor-standing gas boiler, cast iron, atmospheric burner

Logano G234 WS

• Boiler block design with perfectly matched sections
• Boiler sections made of high quality cast iron GL 180 M
• Combustion chamber closed on all sides
• Intensive heat transfer of heating surfaces thanks to special fins
• Easy installation and maintenance thanks to simple design
• Fully automatic operation with electric ignition, no additional gas consumption required for ignition
• To make it easy to connect gas to the boiler at the back, there is a gas pipeline under its casing.
• Thermal insulation 80 mm thick. reduces heat loss to a minimum
• The heating boiler is completely assembled together with the casing - this saves time and installation costs
• Compact dimensions - an advantage when carried through openings and when placed in a boiler room
• Various combinations with control systems and cylinders - to suit every need
• Large selection of additional equipment for quick installation, adapted to a specific boiler

• Fully automatic burner with electric ignition
• Ionization flame control and double magnetic valve
• The Venturi tube of a gas burner ensures mixing of fuel with air. During the combustion process, many small individual flames are formed without a high-temperature core. Therefore, in such gas burners the combustion temperature is significantly reduced. In addition, the short flame of these fireplaces easily breaks away from the burner rod, reducing the heat load on it

• Heating boiler - for operation on natural gas H, with thermal insulation and boiler casing - 1 box
• Conversion kit for liquefied gas P and B/P (additional equipment) - 1 box
• Control system (optional) - 1 box

Flue gas temperature / chimney connection
The required pressure is for all boiler sizes a minimum of 3 and a maximum of 10 Pa.
For more precise adjustment and maintenance of draft in the chimney, as well as for organizing ventilation of the chimney itself, it is recommended to install and adjust an additional air regulator (draft limiter). The cross-section of the additional air regulator depends on the effective height and cross-section of the chimney.

Flue gas shut-off valve
If desired, a flue gas shut-off valve can be purchased as an optional extra. A flue gas shut-off valve installed before the draft breaker is more effective than one installed after it.

Installations with underfloor heating
In floor heating systems using oxygen-permeable plastic pipes (DIN 4726), it is necessary to install a heat exchanger between the heating boiler and the floor heating system.

Preparing hot water
The heating boiler can work with any water heater tank. Combinations of the boiler with tanks of the Logalux ST/SU series have particular advantages.

General provisions

• For heating boilers that must be equipped with a flue gas monitoring system according to the FeuVO of the relevant federal state, accessories can be supplied
• For version B11 (without flue gas monitoring system), the boiler may only be installed in rooms that have the required ventilation to the atmosphere and also have a self-closing and sealed door, for example in boiler rooms
• For version B11 BS (with flue gas monitoring system), the heating boiler can be installed in apartments or similar places
• To ensure the functioning of the boiler, all connections must be made in the places specified for them
• When installing a gas heating boiler operating on liquefied gas below ground level, it is recommended to install a second solenoid valve. A switchgear for controlling the solenoid valve can be supplied as an option
• In installations with underfloor heating, with several heating circuits, as well as in installations with large water volumes, it is necessary to install a mixer to regulate the heating circuits, based on local operating conditions.

When installing the heating boiler, the minimum distances shown (indicated in parentheses) must be observed. For ease of installation, servicing and maintenance, it is necessary to maintain the recommended distances from the walls.
The room for installing equipment must be protected from the cold and have good ventilation. In addition, care must be taken to ensure that the combustion air is not contaminated with dust or halogenated hydrocarbons. Halogenated hydrocarbons of all types are found, for example, in aerosol cans, solvents and cleaners, varnishes, paints and adhesives.

Modern universal boiler concept

• Low temperature heating boiler according to DIN EN 297 with continuously variable boiler water temperature control without base temperature (minimum boiler water temperature)
• Four certified boiler sizes with a nominal heating output of 38-55 kW
• The heating boiler is designed to operate on natural gas H and liquefied gas P / B/P
• Boiler design with perfectly fitted sections made of high-quality cast iron
• Tested and reliable heating boiler with cast iron heat exchanger and atmospheric gas burner
• Combines with adjacent Logalux ST and Logalux SU water heater tanks from the Buderus program
• Can be combined with various control systems from the Buderus program
• High standardized utilization rate (93%) and low emissions of harmful substances

• Atmospheric gas burner with pre-mixing without fan
• Heating mode without additional noise reduction measures
• Stable operation on natural gas with supply pressure up to 10 mbar

• Control functions coordinated with the plant hydraulics
• Easy setup of all control system functions (Push and Turn principle)
• It is possible to expand the configuration of all control systems for additional modules

• A system for quickly installing the heating circuit, adapted to the corresponding hydraulic circuit, for connecting it to the boiler or mounting it to the wall
• Convenient connection of Logalux ST and Logalux SU water heater tanks with a capacity of 150, 160, 200 and 300 liters to the boiler thanks to the boiler-water heater connecting pipeline with loading pump and check valve
• Burner design without moving parts
• Easy conversion of the burner to other types of gas

The floor-standing gas cast-iron heating boiler “Buderus Logano G234X (WS)” with a power of 60 kW with an atmospheric burner appeared in an updated version in 2017 - with modern standard automation EMS Plus and spectacular industrial design from Buderus. This new generation boiler has retained the basic qualities of its predecessor, such as high performance at low costs, reliability, efficiency, compactness, and also has a power of 60 kW. Works on both natural and liquefied gas. The boiler is designed for heating large buildings, since it can be used to organize economical heating when high power is required. In combination with high-quality floor-standing water heaters "Buderus" of the "Logalux ST" and "Logalux SU" series, it allows you to implement a comfortable hot water supply system.

The atmospheric gas burner with pre-mixing, which the boiler is equipped with at the factory, does not have a fan, which ensures silent operation. There is no need for additional noise reduction measures during heating mode. The burner operates fully automatically, ignition is electric and does not require additional gas consumption.

The low-temperature heating boiler “Logano G234X (WS)” is equipped with an efficient heat exchanger with 7 sections, made of high-quality gray cast iron GL 180 M. The sections are ideally matched to the design of the boiler block and have special fins, due to which there is intense heat transfer from the heating surfaces. The boiler is equipped with 80 mm thick thermal insulation, which, together with the cladding, prevents energy loss.

The new boiler model “Logano G234X (WS)” was designed specifically for the installation of the modern control system “Buderus Logamatic MC110” standard EMS Plus. This automation is optionally equipped with a “RC 310” or “BC 30 E” controller with a touch screen and full-text menu. Such a system allows you to work in a weather-dependent mode, controls the boiler and indirect heating boiler, recirculation line, 3-way valve, and also informs about the current status, selected functions, and errors. Control is carried out using a 0-10 V signal. Setting up all options is intuitive and very simple - according to the “Push and turn” principle. All control functions are coordinated with the installation hydraulics. The control system can be expanded with additional modules: mixing modules, Internet connection module, cascade module with the ability to control up to 4 boilers, modules for solar systems. For complex systems, it is recommended to use the new generation of professional automation “Logamatic 5000”. The control system is not included in the boiler delivery and must be ordered separately.

The “Logano G234X (WS)” boiler is delivered fully assembled, with casing and gas burner, which allows you to significantly save installation time and costs and allow quick commissioning. The quick installation system for the heating circuit for connection to the boiler or wall mounting is adapted to the corresponding hydraulic circuit. The water heater tank is conveniently connected to the boiler using a connecting pipeline with a loading pump and a check valve. The burner design has no moving parts, and its conversion to other types of gas is as simple as possible. Since the combustion process occurs with virtually no soot formation, maintenance and cleaning work is reduced to a minimum. This heating boiler is pre-set for natural gas. For conversion to liquefied gas, a special conversion kit is used (optional).

Main features and advantages of the Logano G234X (WS) boiler:

• One standard size with a nominal heating output of 60 kW
• Cast iron heat exchanger with finned heating surfaces
• Ideally structurally matched sections made of gray cast iron: 7
• High standardized efficiency: up to 92%
• Options for operation on natural or liquefied gas
• Fully automatic atmospheric burner with electric ignition
• Burner control SAFe
• Ionization flame control and double magnetic valve
• Low emissions of harmful substances
• Quiet and reliable operation
• Combustion chamber closed on all sides
• The presence of a gas pipeline under the casing of the boilers for ease of connecting gas from the rear
• Richer functionality due to combinations with standard control systems EMS And EMS Plus from the program "Buderus" (optional equipment)
• Simple and convenient control
• Low-temperature, economical operating mode to reduce heating costs
• Smooth control of boiler water temperature without basement temperature
• Possibility of combination with a number of installed boilers “Logalux ST” and “Logalux SU”
• 80 mm thick thermal insulation, reducing heat loss to a minimum
• Quick installation - boilers are already completely assembled with casing
• Compact dimensions - convenient to carry through openings and place in the boiler room
• Easy installation and maintenance thanks to simple design
• Case of a new “industrial” design in black and blue design
• Modern high quality technology
• Large selection of additional equipment adapted to the boiler for quick installation