Attaching blinds to the frame of a plastic window. Installation of fasteners for blinds to the ceiling and wall. We attach horizontal blinds to wooden windows

Residential buildings and restaurants. The products are designed to preserve the intimacy of the atmosphere, protect against sun rays. In order for them to look harmonious in window opening, they must be installed correctly. You can watch how various blinds are attached to plastic windows in the corresponding video or read the instructions. Depending on the shape of the product, the types of fasteners will differ. Next, we will talk about the main installation methods.

Blind installation options

The installation method is influenced by various factors, however main role presence plays flat surface. If the walls are curved, they must be leveled to avoid complications during installation. The following options exist:

• Ceiling mount;
• Installation on walls;
• Placement inside a window opening;
• Installation of blinds to each double-glazed window.

When choosing a method, you should focus on the design. The sequence of the work itself will differ little.

There are several options for attaching blinds to a window opening, both with and without drilling

Installation stages

The versatility of blinds implies a similar procedure for different mounting methods. The differences will only be in the details.

1. First of all, it is necessary to measure the window opening. If the owner decides to secure the products in a third way (in the window opening), then a couple of cm will need to be subtracted from the received data. This will avoid the awkward situation when the blinds drag along the window sill. If the user decides to install it with an overlap, then, on the contrary, an extra cm will be required. To reliably close the window, 4-5 cm on the wide side will be enough. The length can even be up to the floor. Here you need to focus on your own sense of taste. If the owner chooses the 4th installation method, then measurements of each sash will be required. In case of detected curvature, it is recommended to adjust the measurements as for the correct figure.
2. Marking. This refers to the marking of fasteners, which must be located symmetrically and accurately. Geometry has important, since the reliability of the design of the blinds itself will depend on this. Already during marking, it is necessary to check the possibility of opening and closing the window. The product should not interfere with the owner’s ability to ventilate the room. It is also important to determine the location for the cord, since this is where the point of greatest pressure will be. In particular, it is recommended to provide additional fastening.
3. Installation. Self-tapping screws are installed directly into walls or ceilings. After they are screwed, a curtain rod is hung on them to secure the blinds. Then you can test the product itself.

Blinds diagram

Nuances of installation depending on the type of plastic products

In order not to damage plastic windows when installing blinds, it is necessary to carry out the work extremely carefully. Let's consider the subtleties of installation for different types of products:

• Vertical blinds. This type is in greatest demand because it allows the designer to experiment with color and shape. The range of blinds is extremely wide. For installation, not much is required: a cornice, blind slats, a chain with runners. The latter must be of sufficient length so as not to limit the operation of the device itself. This is especially true if the window has a non-standard shape.

The products can be mounted on a ceiling or wall mount. In the first case, you should focus on the width of the lamella in order to determine the area where the cornice will be placed, that is, the distance from the wall. Mounting to the wall implies the possibility of placing the cornice both under the ceiling and above the window itself. After installing the brackets, runners for hanging slats are installed on the built-in cornice.

Various options for installing blinds on a window

Since vertical products do not function without weights, they will need to be hung on both sides of the blind somewhere below.

• Horizontal blinds. Often these products are installed in the second or fourth way. Installation on the wall is required when the owner wants to completely close the window opening. And installation on each sash allows you to maintain functionality plastic double glazing. Installation work involves going through the same stages as in the case of vertical products.

Installation of blinds with and without drilling

There are two main options for attaching the cornice. The first method involves the use of self-tapping screws, and the second - L-shaped fasteners.

Self-tapping screws allow the owner to install horizontal products directly onto the window profile.

Attention! The latter will not experience significant damage, since the holes can always be sealed with white sealant.

Before drilling, markings are made. To do this, install the blinds in the cornice and open them completely, after which they bring them to the window. Visual assessment should make it clear how accurately all measurements were taken, since next it will be necessary to transfer the markings of the brackets to the profile. There should be no distortions.

Properly attached blinds will decorate the room and serve the owner for a long time

After the drilling operation, the following actions are performed:

1. The cornice is screwed using brackets;
2. The fastenings are closed;
3. A hook with a cane and a tip is installed in the control unit;
4. The bell is secured with a knot;
5. Then, using a cord, the product is lowered to the end to fix the blinds at the bottom.

L-shaped brackets are attached without drilling, which will need to be purchased separately. The simple snap-on method greatly simplifies the maintenance of windows and blinds. These brackets cling to the top of each sash, unless it is blind. This type fastening is considered the most suitable for installing the product inside a window opening. The use of the same adhesive tape does not guarantee the same degree of reliability that special brackets can provide. At the same time, they maintain the integrity of the window profile, which is important.

Following these recommendations, the user can install blinds on plastic windows independently. Depending on the shape of the product and the features of the window, you will need to choose the best way fastenings He considers the method without drilling to be the best.

Video: How to attach blinds to plastic windows

Photo: How to attach blinds to plastic windows

Blinds, which 10 years ago looked like real foreign exotica, have now become firmly established in our lives. Most office premises and institutions have switched from using standard curtains to universal blinds, which generate less dust, look more formal and are incredibly comfortable.

Blinds are used even in rooms designed in classic style, because their functionality, ease of care and appearance are excellent. In addition, blinds provide effective protection spaces from sunlight, allow you to easily adjust the level of illumination in the room, and reliably screen the room from prying eyes.

Installing blinds yourself

The installation of blinds must be carried out according to all the rules, otherwise you risk getting a lot of problems: the curtains will not move, the curtain will be difficult to assemble, etc. High quality installation provides blinds with long service life. When installing, you need to take into account the design features and the specifics of the walls (or window frames) in the room.

Installing blinds yourself

Types of blinds

PVC window manufacturing companies offer blinds in a wide variety of shapes and sizes. Depending on the purpose, blinds are made from:

• plastic;
• wood;
• aluminum;
• fabrics.Wooden horizontal blinds

There are different types of blinds:

• vertical;
• roll;
• horizontal.Roller blindsVertical blinds

These types differ significantly in the location of the slats and installation methods.

Vertical blinds are rare in ordinary residential premises; they are more often used in offices. They are mounted above the top edge of the window, similar to curtains, although this may negatively affect their functionality.

A roller blinds and horizontal blinds are more often used at home instead of traditional curtains. They are installed not only in the window opening, but also on top of the window.

Vertical blinds String (thread) two-color

Roller blinds are mounted on the front surface of the corner of the upper slope of the window profile.

Blinds with horizontal slats can be mounted directly on the window profile, on each sash. Often, horizontal slats are complemented with curtains with curtains. Installing blinds directly on the window profile saves useful space in the room itself and frees up space on the window sill.

Horizontal aluminum blinds

What are blinds made of?

The design of the blinds is:

• cornice for fastening the canvas;
• runners, thanks to which the strips of blinds move;
• the lamellas themselves (strips of fabric);
• chains or cords that ensure the assembly of blinds. What are blinds made of?

For windows of non-standard shape, you need to use slats of a special length, which the best way will provide light protection to the room.

If your window has two sashes, then when installing the blinds, pay attention to the location of the blind lifting mechanism (right, left).

What are blinds made of?

Three ways to install blinds:

• onlay;
• for each window sash separately;
• directly into the window opening.

A factory set of blinds usually includes all materials for their installation: screws and self-tapping screws, as well as other parts.

Vertical fabric blinds

The choice of installation option is related to the design features of the window: installing blinds on standard double-hung windows is a little easier than on inclined roof windows.

One of the most difficult is the installation of blinds on PVC windows, since working with plastic compared to, say, wood, has a number of specific features.

The installation of cornices on plastic windows must be carried out as carefully as possible and it is better to do this in the warm season (at temperatures above +5 degrees Celsius).

Design horizontal blinds

Installation of blinds on a window sash can be done using self-tapping screws, brackets, or by drilling holes in the frame. This is the most durable and reliable.

Important! The tightness of the profile does not suffer when the blind cornice is attached to it using drilling. If it becomes necessary to remove the cornice and there are holes left in the frame, they can be filled with white silicone sealant.

If you don't want to drill holes, use brackets that attach to the frame without drilling.

Important! In most cases, blinds can be attached to screws that are already in the window profile. This installation method is no less reliable than drilling holes. You can learn about the possibility of such a simple installation from the blinds’ instructions.

Progress of installation of blinds

After unpacking the blinds, read the instructions. Installing blinds means: measuring the window and adjusting the dimensions of the blinds to it; then install fastenings for the cornice and cord system; assemble the strips onto the cornice and check the functionality of the system.

1. Measurements and markings

Measurements and markings

Measurements are necessary so that later it will be convenient to use the light-protective sheet without complaining about distortions or frequent breakdowns. It is especially important to check the dimensions of the canvases and adjust them to the place of attachment if the window opening has a specific geometric shape.

Before screwing, you need to mark the position of the fasteners with a pencil, checking them with a level and a tape measure to avoid a skewed fit and leave room for adjusting the container, and also to ensure that the slats do not extend beyond the window glass.

2. Installation of cornice and slats

Installation of blinds

Before installation and actual installation, it is necessary to mark the fasteners with maximum accuracy and symmetry. Additional fastening must be provided for the control cord so that the structure can withstand the additional load.

All elements are fixed to the wall with screws or dowels. Next is the installation of the cornice. The slats and runners themselves will be attached to it.

The rigidity of the structure is guaranteed by the upper cornice strip, so there is no need to further strengthen the strip with glue, sealant or foam - it is fixed quite rigidly.

When re-installing, you need to measure the width of each window sash so that window fittings did not interfere with the free hanging of the slats.

Also, when choosing an installation “in the window opening,” you need to reduce the height on each side by 2 cm so that the canvas does not touch the window sill.

To secure the blinds close to a plastic window, you need to drill the plastic window frame according to the markings - pre-drilling will prevent cracking of the plastic.

The height of the blinds must be no less than the height of the window opening

If the plates on which the blinds are hung do not fit tightly to the window profile, use pads.

Brackets for blinds are screwed into the holes using self-tapping screws. Next, you need to secure the brackets upward with latches and insert the container with the blinds into them.

Brackets for blinds are screwed into the holes using self-tapping screws.

The lower holders are attached like this: lower the curtain to mark the lower points (the canvas should be loosely stretched). Using these marks, drill holes into which you need to screw the lower holders that secure the canvas in the “micro-ventilation” position. Make sure that the staples sit firmly in the plastic.

When installing with an overlay, you need to add 5cm in width so that the entire opening is closed. The height is adjustable at will and can reach the window sill or the floor itself.

There are a number of modern methods for installing blinds, which involve installing a cornice with slats on brackets attached to the window frame without drilling. The cornice with stripes is simply hung on the brackets and snaps into place. The design is collapsible, which allows you to remove the blinds when you need to wash the window glass or wipe the slats. This is the easiest way to install blinds.

Blinds on bracket

Features of installation of blinds by type

Vertical blinds

Before installation begins vertical blinds you need to decide whether wall or ceiling mount for the cornice. The height of the light-protective sheet depends on the place where the cornice is attached.

Vertical blinds installation diagram

The thickness of the guide for vertical blinds should be at least 5-6 cm; such a gap will ensure free movement of the slats. If there is an obstacle between the blinds and the wall (batteries, etc.)

), then you will need to install an additional bracket, which is not included in the kit; it must be purchased separately.

If you want the blinds to be at some distance from the wall (there are different cases: pipe, etc.

) additional bracket must be purchased

Bracket Attachment

For vertical blinds, the order in which the slats are hung is also important: they need to be attached to the cornice in the same order as they were in the factory box. Also, before installation begins, it is necessary to determine the correct direction of the pendants. Correct position, when in closed you can't see the seam on the blind material.

Figures 1A and 1B show possible options for installing blinds

Don't forget to place the bottom weights on the vertical strips so that the canvas looks even. Cargo from external and inner sides connected to each other by a chain. The plumb line is attached to a cord that is included in the kit. Various manufacturers use plumb lines of different shapes.

Secure the curtain rod with latches

Attach the bottom chain to the weights

Install weights on plates

Installation of weights

Connect the records

Straighten the blinds, the slats should be parallel to each other

There are many different mounts for vertical blinds in stores, but they are often unreliable. The safest way to mount the blinds is to use a pair of brackets that need to be screwed to the wall with self-tapping screws.

Roller and horizontal blinds

Installation

Horizontal and roller blinds, like vertical ones, can be equally conveniently installed on a wall, attached to a window or ceiling. The main thing is to clearly measure whether the canvas will interfere with opening the window. If this happens, if possible, you need to cut a hole in the strips in advance for comfortable opening of the window sashes.

Installation of horizontal blinds (slat width 50 mm)

Insert the horizontal blind curtain rod into the brackets and close the bracket locks

Horizontal blinds - installation instructions

When attaching with double-sided tape, do not forget to thoroughly remove dust and degrease the surface.

You have convinced yourself that self-installation making blinds is quite simple if you know a few tricks to make the process easier. Good luck using your own blinds!

By the way, you can also read about repairing blinds with your own hands on our website.

– Installation of horizontal blinds

– Installation of vertical blinds

– Installation of blinds without drilling

Source: https://svoimi-rykami.ru/remont-kvartiry/okna/ustanoa-zhalyuzi-svoimi-rukami.html

How to install blinds on windows

A few years ago, curtains began to be replaced everywhere with blinds. Now they can be found in offices and living spaces, in shopping areas and on the windows of cafes and restaurants.

They look great, give the room a modern, individual look, and perfectly protect the room from intrusion. prying eyes and excessive light.

Recently, in addition to the usual horizontal and vertical options Cassette blinds have appeared; they are often attached to the back side of the window opening.

Features of installing blinds

In order for blinds to serve for a long time, you need to be extremely careful when installing them. Only a balanced, competent approach will ensure the normal functioning of this rather complex structure. But if you understand all the nuances, you can install blinds in place very quickly.

The main thing is not to forget about the features of each design and take everything into account in the assembly. The installation process is influenced by the walls, namely how smooth they are.

Any deviations from the correct level, both horizontally and vertically, will lead to significant complications during operation. Therefore, if in your case there are obvious curvatures of the walls, it is better to invite a specialist with experience in solving such issues.

If you still decide to install blinds on your own, you need to study the available information, delve into all the details, and be patient.

There are four ways to install blinds.

1. Inside the window opening.
2. For each window sash respectively.
3. To the ceiling
4. On the walls.

When choosing an installation method, you should be guided by your preferences. You can decide which method is right for you based on the design of the window.

In principle, blinds can be installed on any windows, including attic windows, but the mounting method will have its own characteristics. The sequence of actions will be similar in any case.

Installation methods differ from each other only in some small details.

Sequence of actions when installing blinds

Measuring is the first step

First you need to correctly measure the window opening. Each type of installation has its own nuances that must be observed when taking measurements. This must be done in order to navigate the size of the blinds and decide on a suitable design.

If you decide to attach the blinds with an overlap, you need to add 5 cm on each side in width so that the window is completely closed. The length will depend on your preferences or the designer’s advice. It can only be slightly below the window sill, or it can reach the floor.

If you plan to attach blinds to each window sash separately, then you need to measure these parts of the window without taking into account the fittings. When taking measurements, you must try to be punctual. Only correct measurement and ideal geometric proportions will give impeccable appearance and uninterrupted functioning of the blinds in the future.

If the measurement reveals the curvature of the window, you should try to adjust the parameters to the correct figure.

Marking - step two

Before installation, mark the fasteners. Since the design of any blinds is geometrically verified, markings must be carried out with millimeter precision; symmetry is also of great importance.

While marking, you need to check how the light-protective devices that you have prepared will work. Will it be possible to open and close the window freely after installing them?

Having determined where the control cord will be, you need to mark this place and make additional fastening in this area. It is necessary because more pressure will be put on this area.

Installation - step three

Guided by the markings, you need to attach all the existing parts using dowels and screws. They are screwed into the wall or ceiling. The cornice is hung on these screws. It is used to fix runners and slats, which are simply threaded into the prepared cornice. After completion of work, the functionality of the light protection device is checked.

Features of installing blinds on plastic windows

Quite often it is necessary to install blinds on plastic windows. And this is not very simple. In this case, both the blinds themselves and the window can be rendered unusable quite quickly. To avoid unpleasant consequences, all manipulations must be carried out with maximum caution.

The main subtleties that must be taken into account when working with different types blinds

Vertical blinds

The most popular is the vertical variety. It is used in offices, public institutions and in ordinary home environment. Color variations are limitless, and the ability to combine colors and shapes gives scope to the most daring design ideas. To install vertical blinds, you need to prepare all the necessary elements:

• cornice;
• slats;
• runners;
• chain.

If the window has an unusual format, you should provide a chain of appropriate length so that it looks appropriate and does not limit the functionality of the entire device. Vertical blinds can be mounted to the wall or ceiling.

If you decide to mount the device to a wall, you can choose an area just above a window or directly near the ceiling.

If you attach the cornice to the ceiling, then you need to choose an area close to the wall surface at a distance slightly greater than the width of the lamella.

When were the blinds purchased? the right size, colors and quality, mark the fastening elements and install them. Once the brackets are installed, the cornice is attached to them. Runners are put on the cornice and slats are hung on them. When hanging the slats, you must follow the order in which they were placed in the packaging.

Finally, you should take care of the weights. This type blinds cannot function without them. These weights are suspended at the bottom of the device on chains on both sides (inside and outside).

for installation of vertical blinds

Horizontal blinds

This type of blinds has not lost its relevance for many years. Plastic devices are used everywhere, because they are so easy to choose by color and size.

Their design features sometimes cause difficulties for beginners, and they cannot install this type of window decoration.

Horizontal blinds are most often installed on the wall, sometimes they are attached directly to the window. They are mounted to the wall if it is necessary to completely decorate the window opening. Attaching to a window means mounting to the sashes; this option does not limit the functionality of the window itself. It can be easily opened and closed without any obstruction.

Self-installation of horizontal blinds includes the same steps as in the case of the vertical variety:

• froze;
• marking;
• cornice fastening;
• installation of blinds.

You can fasten the cornice using self-tapping screws. It is quite simple to attach horizontal blinds to the window profile. The actions are minimal, but the result is quite decent. There is no need to worry about the profile; the holes from the self-tapping screws will not cause any significant damage to it. If in the future you want to remove the blinds, the screws are simply unscrewed and the holes are hidden with white silicone sealant.

Before you drill a hole, you need to make sure your markings are correct. To do this, the fasteners are inserted into the cornice and pulled by the cord. Let the blinds open all the way.

Next, they are brought to the intended mounting location and visually assessed whether the markings are applied correctly and whether the blinds will open smoothly if they are mounted as planned. If there are distortions, you need to make more correct marks with a pencil.

Then the brackets are removed from the cornice, they are brought to the marks and points are precisely placed in the places where the self-tapping screw will be screwed in.

installation of blinds on plastic windows

When the holes are ready, the brackets are screwed to them and the cornice is hung. It is inserted into the fasteners, and then they are closed. Next perform the following steps:

• installing a hook in the control mechanism;
• installing a cane in a hook;
• the tip is attached to the cane;
• installing a bell, securing it with a knot;
• blinds are lowered by a cord;
• installation of lower fixation with a self-tapping screw.

In general, installing blinds is not difficult. However, you must comply with all requirements, be careful and careful. You cannot ignore the instructions that come with the purchased blinds.

installation of horizontal blinds

Installation of blinds without drilling

Some types of modern brackets can be attached to the frame without drilling. It is very comfortable. Such blind systems are mounted on brackets using conventional snaps. In this case, they are not only easy to attach, but also easy to remove to wash the window or tidy up the slats themselves.

To attach the brackets without drilling, you need to purchase a special variety of these fasteners. You need L-shaped brackets; they can be easily hooked to the top of the window sash. They can also be easily removed if necessary.

But such a bracket cannot be attached to a blind sash; this is only possible with opening sashes.

If you have solid shutters, and the blinds must be installed without drilling, you should use reliable double-sided tape with a foam base.

The L-shaped fastening is considered the most optimal when attaching blinds inside a window opening. It maintains the integrity of the profile, ensures reliable fixation of the blinds, and is easy to put on and take off. Fastening with tape is less thorough. It will last long years, if it is not given excessive loads, but if handled carelessly it can quickly break.

Plastic blinds are more discreet than fabric ones, but they are durable and inexpensive. Roller blinds are another way to create a unique interior space; they can be made of fabric, bamboo or wood.

Blinds are optimal device providing protection from sun rays. Various design options allow them to be a real decoration of rooms, creating unique style Houses.

please select a piece of text and press Ctrl+Enter.

Source: http://kvartirnyj-remont.com/ustanoa-zhalyuzi-na-okna.html

How to attach blinds to plastic windows, with screws and tape

Installing curtains on the doors looks not only cozy, but also modern

Hello. This time you will learn how to attach blinds to plastic windows. The topic of the article is interesting because plastic or aluminum blinds are everywhere replacing less practical fabric curtains. Therefore, if you decide to make the windows in your apartment more modern and easier to use, the following photo reports on the completed installation are exactly what you need.

Current fastening methods

Attaching blinds to a plastic window is done in two ways:

• Using self-tapping screws - the PVC profile will be drilled, and therefore when dismantling the blinds there will be holes that will not be easy to cover;
• Without the use of self-tapping screws, the PVC profile will be intact and this is good, but the structure installed on top of the profile will be held less firmly in comparison with analogues fixed on self-tapping screws.

I don’t know which horizontal blinds you chose, and therefore I’ll tell you about the installation of each of the listed varieties separately and in detail.

Installation using self-tapping screws

The blinds package includes the following:

• The main structure is made of 2 lamellas. (one for each leaf);
• Fastening elements for the upper part, 2 pieces per sash;
• Fastening elements for the lower part, 2 pieces per sash;
• Self-tapping screws 20 mm long, 4 pcs. for each sash.

DIY installation instructions are as follows:

This is all we need for installation

• Unpack the blinds and unwind the adjustment cord;

Before attaching the device, we remove everything from it that may interfere with installation

• Remove the adjusting bar (cane);

Fastening element installed on the upper profile

• We attach the upper fastening elements to the upper profile of the device so that the fastenings do not interfere with the operation of the mechanisms located inside the profile;

Optimal position of the bottom bar

• Next, we open the slats so that they take the position characteristic of open blinds;

• We apply the upper profile to the window so that the lower strip is located just below the bead on the frame, that is, so that the glass is completely covered;

Trying on the upper profile with fastenings

• Mark the location of the fasteners on the window frame;

When making markings, I recommend using a spirit level so that the top bar is located exactly horizontally and does not have any distortions. If the window was initially installed skewed, we make markings not according to the spirit level, but taking into account the location of the sashes.

We screw the fastenings

• Using pre-made markings, we install the fastenings with self-tapping screws;

Surface PVC profile smooth, and therefore it will most likely not be easy to tighten the self-tapping screw according to the mark. Therefore, before screwing in the screw, we drill holes in the profile with a diameter of 2 mm, which is 1 mm less than the diameter of the screws. It will be easy to screw in the screws using the pre-made holes.

Click on the profile

• After the fasteners are installed, apply the top bar to them and click it in with a little force;

We install plugs not only for beauty, but also for greater reliability of fastening

• From the outside, we finally fix the structure with plugs, which are placed on the holders until a characteristic click appears;
• We lower the blinds so that the lower slats are in the lowest position;
• We make markings under lower mounts so that they are located at the level of the ends of the bottom bar;

Fastenings for the bottom bar

• We install fastenings on self-tapping screws;
• We snap the bottom bar into the fastenings;
• We install the adjustment bar on the original mount;

Unfortunately, vertical blinds cannot be installed this way, since they are placed not on the windows, but on the wall

• Checking functionality installed blinds, opening and closing the gap between the slats.

Operation and Maintenance

So we found out how to attach blinds to plastic windows with self-tapping screws. Among the recommendations for the use and maintenance of installed structures, I note the following:

• We rotate the adjustment bar around its axis smoothly since the hook with which it is attached to the mechanism is quite fragile;
• In order to wash the window, we snap off the lower lamella and assemble the blinds upward; this is enough to wipe the entire glass;
• I recommend removing dust from the slats with a peacock broom;
• I recommend that immediately after the dust has been removed, apply an antistatic aerosol, any one of your choice, to the slats.

Installation without using self-tapping screws

Now I'll tell you how to attach plastic blinds on modern double-glazed windows without the use of screws.

In what cases can fastening without drilling be relevant? There are many such cases, for example, the use of rented housing, where, according to the terms of the contract, elements of the surroundings cannot be damaged.

Adhesive tape is a component necessary for installation without drilling frames

For execution installation work you will need a set of regular horizontal blinds with light plastic lamellas, double-sided tape and ordinary scissors.

The instructions for attaching blinds to plastic windows without using self-tapping screws are as follows:

All parts are laid out and ready for installation

• Unpack the set of blinds;
• We disconnect the adjustment bar from the main unit so that it does not subsequently interfere with the installation;
• We lay the main block with the wrong side up;
• Unwind the double-sided tape to the length of the body;

Trim off excess tape

• Remove the tape from one side protective film and glue it on reverse side block, as shown in the photo;

We select double-sided tape so that the width of the tape is equal to the width of the blind block. We glue the tape so that it is flush with the walls of the block. In addition, carefully smooth the glued tape from the inside out so that it sticks evenly over the entire surface.

• We apply the blinds to the window and determine their position on the top of the window sash;
• Having decided on the location, we make marks on the profile corresponding to the ends of the block;

• We install the previously removed adjusting bar and the installation can be considered complete.

We check the functionality of the installed structure

How firmly will blinds be held when glued with double-sided tape?

The actual operation of blinds installed on tape shows that for 1.5 years the structure lasted without any changes, that is, it did not warp or fall. I think that over the next two or three years the situation will not change.

When installing a block of blinds, only the upper part is glued to the tape, while the lower strip is not fixed. This has virtually no effect on the operation of the device, except that when the shutter is opened towards you, the lower part of the blinds will move forward and touch indoor flowers on the windowsill.

I told my friends about this installation method. They told me that the method is not bad, but they will not use it, since the tape, after removal, will leave characteristic marks that are difficult to remove. Is it really?

There will be marks, but it will be easy to remove any remaining glue from the frame. Simply moisten a cloth with sunflower oil and wipe plastic surface and the glue stains will disappear by themselves. For more effective removal stains from tape, moisten a rag not with sunflower oil, but with WD-40 liquid.

By the way, you can successfully use these methods to remove traces from any tape and from a variety of stickers.

Blinds have recently gained extraordinary popularity not only in offices; they are also happily placed in residential premises. Attaching blinds to windows provides excellent protection from direct sunlight without interfering with ventilation or opening the windows.

Manufacturers offer several types of blinds

• Vertical;
• Horizontal;
• Accordion or pleated;
• Roll type of folding.

Vertical blinds look like vertical slats(strips) connected to each other, which move around their axis using a plastic chain. And also, they can be moved left or right.

The operating principle of horizontal blinds is the same as vertical ones. Only folding occurs from bottom to top.

Pleated - they look like an accordion, for this they are impregnated by special means so that they keep their corrugated shape. They can be attached to both a plastic window and a window opening.

Roller blinds - have the appearance of a continuous canvas that can be rolled into a roll, while opening or closing part or all of the window.

Depending on their materials, lamellas can be:

• metal;
• wooden;
• bamboo;
• plastic;
• made from fabric.

What kind of blinds are the best option for the balcony?

Before you start placing blinds on plastic windows, you should understand whether they are needed at all. Will they become a hindrance when closing or opening the window?

One thing is certain - if a loggia or balcony is converted into a separate room, then blinds are definitely needed.

When choosing blinds, in addition to design and appearance, special attention should be paid to the following points:

• functionality and practicality of fasteners;
• It should be taken into account that not all types of fastenings are suitable for window units;
• practicality of blinds;
• It is better to choose plastic or fabric material for the balcony; wood and bamboo can create unnecessary noise.

Which better than blinds to the balcony?

For balconies and loggias, plastic blinds are best suited because:

• they are easy to clean and wash;
• do not lose their appearance over time;
• resistant to sunlight.

Before taking measurements, you need to decide where you want to install the blinds:

• on the window sash itself;
• on part of the wall above the window;
• into the window opening.

How to take correct measurements?

If you decide to install blinds yourself, then you need to know a few important points. Windows do not always have a completely even shape, therefore, for measurements it is better to use a steel tape measure and measure everything down to the millimeter, in different places opening.

For a certain type of fastening, there are some nuances in measurements:

1. If you are planning to install blinds on the wall, above the window opening, you should understand that the cornice will take approximately 5 cm. The length of the blinds is up to you to determine: either they will completely cover the window opening, or only to the lower edge of the window. According to the width of the blinds, you should set: 10 cm more than the opening;
2. When installing blinds on a window sash, you need to measure the distance between two vertical glazing beads (this will be the fastening). You also choose the length yourself, and the width should be 3 cm larger than the glass to avoid unnecessary clearance;
3. Placing blinds in the window opening is considered the most difficult procedure. The parameters are measured: according to the width and height of the window, while the height is calculated as the length of the glass with the addition of 1 cm to cover the rubber seals. It is important to consider that when folded, the blinds do not interfere with opening the window.

Basic window mounting options

There are two main methods for installing blinds on plastic windows, with and without a drill. The slats of the blinds are located on the cornice, and how this cornice will be held on the window, at the top of the wall or in the window opening, depends on the installation method.

Drilling installation method

Window blinds plastic doors- are attached separately for each.

The cornice is applied to the upper edge of the sash and the places where it is attached are indicated. For greater accuracy, at the places where screws are attached, it is better to drill neat holes in advance. We attach the bracket, screw in the screws and fasten the cornice.

Afterwards you need to fix the fishing line that holds the slats. We make small holes directly opposite the line exit under the glazing beads at the bottom of the sash. We thread the fishing line through the plugs, and fix the plugs themselves into the holes.

The drilling method is used by placing cornices on the ceiling or wall on top of the window. To do this, make appropriate holes into which dowels are driven and brackets are secured with screws.

How to install blinds on plastic windows horizontal video:

Fastening method without drilling

Holes in window sashes and walls can cause a lot of inconvenience when you decide to remove your blinds. Therefore, you can use analogue types of mounting brackets on windows:

• Using double-sided tape.
• For the top of the opening sash, when the bottom is fixed with small magnets;

This method is very easy to use, and it does not injure window frame and walls. With this mounting, removing the blinds to clean them from dust will not be difficult.

Unlike window frames, blinds have a strict geometric shape, the slightest curvature of the fastening will immediately be reflected on appearance.

How to attach blinds to plastic windows without drilling video:

Nuances when attaching different types of blinds:

• Vertical blinds

The peculiarity of mounting vertical light filters is that they are suitable for mounting on a window opening, wall or ceiling. They are not suitable for mounting on sashes and are attached only by drilling.

• Horizontal blinds

The most standard blinds that are suitable for almost any plastic windows. They are considered universal; it is possible to mount them both on each sash and between frames.

• Roller blinds

For ease of use, it is better to install roll filters on window sashes. If they are placed in a window opening or attached to a wall, then it will not be possible to close or open the window with the filters closed. In addition, roller blinds are very delicate; special care must be taken during installation.

Video on installing roller blinds:

How to remove blinds correctly

Over time, like everything else in the house, window structures become covered with dust, so blinds should be removed for cleaning. Each type has its own characteristics when removing.

Removing vertical blinds:

• We transfer the slats to the open state, after which we assemble them;
• We release the chain from the weights and take out the weights;
• We remove each lamella: lift the slider clip and, moving it a little, remove the lamellas one by one.

Removing horizontal blinds:

• Remove the cornice from the bracket;
• We assemble the lamellas at the top and look for the retainer protrusion;
• Pull the lock towards you and to the right;
• We remove the slats.

Removing roller blinds:

• There is a tongue on the bracket; you need to bend it using a screwdriver;
• Remove the shaft by pulling it towards you.

A short video on how to install blinds on plastic windows:

Various designs of blinds - vertical, horizontal, roller - are designed to protect from sunlight and fit perfectly into any interior style. Whichever of them you choose for your windows, it is important not just to hang the blinds, but to ensure their correct operation: raising and lowering, moving and adjusting the position of the slats.

To hang blinds correctly, you first need to carefully measure everything (blinds are not curtains; if they don’t fit, you won’t be able to make them smaller or larger) and mark the attachment points

How to take measurements

If you decide to hang vertical blinds on a wall or ceiling, then first measure the width of the window opening or window sill. It is better that the cornice is longer and protrudes 10-20 cm on both sides of the window, so the room will seem more spacious.

Choose the length of the slats at your discretion: only to the height of the window (to the window sill) or to the floor itself. Fabric lamellas that are too long can be shortened by cutting and hemming on one side.

Vertical blind system large windows provides sufficient daylight and protects inner space from prying eyes

When installing horizontal or roller blinds, you need to proceed from where exactly you plan to place them - in front of the window opening or inside it. Placement on a wall or ceiling requires the possibility of tolerances in the width and length of the structure. If the installation will be carried out directly in the window opening or on its frame, then the blinds must exactly match the dimensions: width (of the entire window or sash) and height.

When you plan to hang blinds on individual sashes of opening windows, it is recommended to measure the width and height of the glass. To them add 2 cm at the top and bottom and 1 cm for the side allowances (0.5 cm each) so that the blinds cover the glass completely, but do not cling to the existing window fittings.

The following video will tell you how to measure a window for horizontal blinds:

Fasteners without drilling

If you are going to hang blinds on a plastic window with your own hands and do without drilling, then the choice will have to be limited to small and fairly light models that can withstand the weight:

• magnetic mounts;
• mounting double-sided adhesive tape;
• reliable double-sided tape (car);
• Velcro fasteners from Command (or another company);
• special brackets that have various options fastenings to the frame: fixed with adhesive tape, tape or glued plates, screwed with self-tapping screws or clinging to the top of the opening sash.

Cassette roller blinds or systemUni

They are attached directly to the sash plastic window using tape, tape or Velcro.

Roller blind, fixed without drilling to the opening sash of a plastic window

Roller blindsMini

For fastening, double-sided tape (adhesive tape, Velcro) is also used, onto which special pads are glued to the frame. The canvas is fixed to them with brackets. When placing roller blinds on the opening sash, magnets are additionally installed to attract the blinds.

Screwing the bracket with self-tapping screws to the sash of a plastic window must be done carefully, as there is a risk of damaging the sealing gasket

Roll curtains

Possible mounting on brackets, tape, tape or Velcro.

Before gluing adhesive tape or adhesive tape, the frame must be thoroughly washed, wiped dry and degreased with an alcohol solution. If you use Velcro, follow the instructions on the package.

Horizontal systems with wooden (bamboo), aluminum or plastic slats (slats)

You can hang blinds on a window using special clips that are attached to the top and lower parts doors, and a cable is pulled between them.

Horizontal systems are hung over the entire width of the window or separately on each sash

For a complete picture of how to hang blinds without drilling using various fasteners, we suggest watching the following video:

All blind systems are usually equipped with detailed instructions manufacturer, installation diagram and set of necessary fasteners.

Drilled fasteners

This type of installation is much more reliable and durable, since screws screwed into a window frame or wall better withstand the weight of the structure and the constant mechanical loads placed on it.

Drilling requires accurate preliminary measurements and perfect alignment horizontally using a level

Drilling the frame leads to damage to the window profile. Although they are insignificant (they do not interfere with sound and heat insulation), if you decide to remove the blinds in the future, when removing the structure, noticeable marks will remain that will have to be masked, for example, with silicone or liquid plastic. Inside the window, roller or horizontal systems. To hang vertical blinds, drill into the ceiling or wall above the window opening.

Installation with drilling can be done independently or entrusted to specialists

For installation you will need:

• pencil;
• building level;
• screwdriver;
• drill (with drills 3 and 6 mm);
• hammer;
• screwdriver (flat or Phillips).

First, we mark the places for the mounting plates or brackets: measure 6 cm from the glass on both sides and mark with a pencil the places for the upcoming drilling. The line between the intended holes must be checked using a level so that it is strictly horizontal. This is important for the correct and long-term operation of the blind system. A window profile (especially not a new one) can crack when screwing in, so it is recommended to first use a thin drill in the marked fastening areas, and then screw the screws into the prepared holes.

On opening windows, holes for fastening brackets are made in the upper part of the sash

Holes for screws for brackets are drilled in the upper part of the sash (on opening ones) or on outside glazing bead (on fixed windows). Then you need to hang the blinds, securing them in the brackets. When placing a blind system inside a window opening, a fishing line (clamp) is pulled to hold the roller blind or slats near the glass when the sashes are opened. A hole for the fishing line is drilled in the lower glazing bead (below the main beads) or on the side of the sash, the fastener is threaded through the plugs, achieving medium tension, and tied into a knot. All decorative and working parts are installed on the mounted structure: trim, latches, fastenings for the lever and chain.

Attaching structural elements of blinds to window glazing beads can lead to glass breaking, so use the smallest self-tapping screws.

When it is necessary to hang vertical blinds, markings and subsequent drilling are performed on the vertical surface of the wall or on the ceiling. The remaining structural elements are screwed to the static brackets secured with screws.

A cornice with special system fastenings (with runners) for vertical slats

To securely fix the brackets in drilled holes insert dowels and screw in self-tapping screws. A cornice with a special fastening system (runners) for vertical slats is mounted on the brackets.

Each lamella of vertical blinds is individually fixed to the eaves so that it moves and rotates freely

Having hung all the slats on the runners, attach the provided weights at the bottom and hang the chain connecting them. Then install decorative panel into the mounting brackets, covering it on both sides with end angles and side panels. All that remains is to check how the blind system you hung works.

When choosing a system and materials, take into account the conditions and purpose of the room in which you plan to hang the blinds, see the table.

Some types of lamellas have a protective impregnation (from fading), which can be erased or washed off if cleaned too often. Therefore, it is important not only to hang the blinds correctly, but also to provide them with proper care and careful operation.

Blind adjustment mechanisms must be handled carefully: avoid sudden twitching and rotation in order to maintain their functionality for a long time

We hope that our tips will be useful to you, and now you can hang the blinds yourself. Share your experience in the comments. Rating: 5.00 (5 votes)

Do you know that:

The habit of using sparingly automatic washing machine may lead to the appearance of an unpleasant odor. Washing at temperatures below 60℃ and short rinses allow fungi and bacteria to dirty clothes stay on internal surfaces and actively reproduce.

Fresh Lemon Isn't Just for Tea: Clean Up Surface Contaminants acrylic bathtub, rubbing half a cut citrus, or quickly wash the microwave by placing a container with water and lemon slices in it for 8-10 minutes at maximum power. The softened dirt can simply be wiped off with a sponge.

Stretch ceilings made of PVC film can withstand from 70 to 120 liters of water per 1 m2 of their area (depending on the size of the ceiling, the degree of its tension and the quality of the film). So you don’t have to worry about leaks from neighbors above.

Threads made of gold and silver, which were used to embroider clothes in the old days, are called gimp. To obtain them, the metal wire was pulled for a long time with pliers to the required fineness. This is where the expression “to drag out the rigmarole” came from - “to do long, monotonous work” or “to delay the completion of a task.”

IN dishwasher Not only plates and cups are washed well. You can load it with plastic toys, glass lamp shades and even dirty vegetables, such as potatoes, but only without using detergents.

If your favorite things show the first signs of gestation in the form of untidy pellets, you can get rid of them using a special machine - a shaver. It quickly and effectively shaves off clumps of fabric fibers and returns things to their proper appearance.

The easiest way to remove scale and carbon deposits from the soleplate of the iron is table salt. Sprinkle on paper thick layer salt, heat the iron to maximum and, using light pressure, run the iron over the salt bed several times.

There are special traps to combat moths. IN sticky layer, with which they are covered, female pheromones are added, which attract males. By sticking to the trap, they are eliminated from the reproduction process, which leads to a decrease in the moth population.

Before you withdraw various spots from clothing, you need to find out how safe the selected solvent is for the fabric itself. It is applied in a small amount to an inconspicuous area of ​​the item from the inside out for 5-10 minutes. If the material retains its structure and color, you can move on to stains.

Large windows in an apartment or house are, of course, good. A lot comes into the room daylight, especially if the windows are new from profile or wood, allowing you to maximize the glass area. However, there is often too much sunlight, especially if the windows face south or east. There are several ways to escape the scorching sun, and the simplest and most optimal of them may be to install blinds on your windows yourself. Other options include replacing double-glazed windows with the installation of tinted glass or using tinting film. Only this option is much more expensive and not as effective if you want to completely block access sunlight into the room.

Types of blinds and mounting features

On this moment window manufacturing companies provide wide choose blinds of various configurations and the ability to make them to fit specific window sizes. Among possible variations There are several main types of blinds:

• vertical;
• horizontal;
• roller shutters (fabric, internal roller shutters).

The option of installing vertical blinds in a residential apartment or your own house is quite questionable. Still, they are too strongly associated with office space. However, they are also suitable for some design solutions interior execution. They are mounted above the window, actually instead of curtains, which further limits their usefulness.

A more extensive number of mounting options is provided by the use of horizontal blinds. They can be installed on top of the window opening and along the outer edge on the upper slope of the window and directly on window design, in this case, separate blinds are installed on each sash. Two latest options They will go well with any curtains and curtains, and choosing the latter type of installation on the window itself will not take up any space on the windowsill. Roller shutters are also mounted directly on each glass.

Choose suitable option Everyone should do it independently, based on their preferences and requirements.

Common methods of attaching blinds

Having decided on the type of blinds to be installed, you can go order them from a good window manufacturer. It’s better, of course, to contact the same company that made your windows. To order you will need to give detailed dimensions windows or the dimensions you require when it comes to blinds installed over the window opening. Blinds are made quite quickly, the technology is as well developed as the production of the windows themselves, especially since the design is quite simple.

Along with the blinds themselves, as a rule, instructions are also included, which tell in sufficient detail how to install the blinds. The whole process is quite simple, and everything can be done with your own hands. If you have some skills in working with a screwdriver, you have the necessary drills, screwdrivers and a ruler with a pencil, then you can begin the installation process and do not need the help of a master installer.

It is worth considering in detail the option of installing horizontal blinds directly on the frame of each section of the window and sash. This process the most complex and visual. Note that the installation of roller shutters occurs in a similar way.

So, the packaging from the manufacturer contains everything you need to install blinds. The main part is wound with fishing line and a control chain. All additional parts and screws are packed in bags. Everything is carefully unwound, and all trim is removed from the curtain rod. There are several ways to attach blinds to a window sash:

1. fasten with screws;
2. use brackets for fastening;
3. the old fashioned way, by drilling holes in the wall;

In the version with screws, holes will inevitably be made in the window profile. This is a reliable and durable method of fastening, especially since the tightness of the entire window and the profile in particular will not be affected. However, for some this may not be suitable, if only because the blinds may have to be removed, and then the holes will already be significant drawback. In order to avoid these consequences, you can use the option of securing the blinds to brackets that are attached to the frame different ways not requiring the creation of holes.

Installation of blinds with drilling plastic or using a screwdriver

In the first option, using screws, it is necessary to place and mark the position of the top bar of the blinds, which will be directly attached to the window, as accurately as possible. The most common and simple option is a structure that is located along the upper edge of the glass unit and only with its wing-grooves extends onto the window frame. Strict attachment to the top of the sash allows you to install the blinds yourself, even without special precision and measurements.

If you have a plastic window, then you don’t have to think about drilling at all. Most manufacturers have blind models that require screws screwed directly into the profile to securely fasten them.

example of horizontal blinds

Attach the carrier to the glass unit at the very top of the sash frame. Due to the different depth between the plane of the glass unit and the frame, the fastening plates may not fit tightly to the window profile. To eliminate this gap and securely attach the plates to the window, special U-shaped pads are used. They are placed from one to several pieces until the gap is completely closed. Mark the position of the carrier along the lower edges of the fastening plates, so that later you can use them as a guide and hang the blinds evenly on the window.

You can attach blinds to plastic windows with screws directly into the profile using a screwdriver. They will easily fit into the plastic and will hold securely. You can first mark the position of the screws and make holes in these places with a drill of approximately 1.5 mm. This, firstly, will eliminate the possibility that when tightening the screw the load-bearing part will move slightly and, secondly, will eliminate the risk of cracks forming in the profile. The latter case is practically unrealistic for new windows, but it is possible if the windows have been standing for several years or are made not of plastic, but of wood.

As soon as the last screw of the fastenings is tightened, you can begin to fasten the fishing line, which will hold the blinds in the plane of the sash when opened. To do this, two holes are made in the lower bead of the sash along the edges. They must be located strictly under the corresponding fishing line exits on carrier system blinds. A 2.5 mm drill is used. The fishing line, threaded into the blind system and lowered at the ends to the bottom glazing bead, is threaded into the special plugs that are included and tied in knots. All that remains is to thread the plugs into the holes and pull the entire line from above. The line tension should not be strong, but it should not sag either.

All that remains is to put the trim on the carrier of the blinds, check their operation and glue them in suitable fastening places for the control chain and flexible lever.

Video: attaching blinds with screws

Installation of blinds without any drilling

Using brackets can help you figure out how to attach blinds to windows without drilling. They are attached to the frame in various ways, and the support of the blinds themselves is snapped or screwed onto them. This system is good because later the blinds can be easily detached for major cleaning, or you can completely remove the blinds from the window and use it without them, if necessary. In this case, there will be no extra holes left in sight, and the tightness of the window profile will not be compromised.

The brackets can be secured, as in the first case, with screws or in one of the following ways:

1. hook on the upper part of the sash profile (installed only on opening sashes);
2. using double-sided tape.

Using the first option allows you to remove even all the brackets from the window in one fell swoop and does not require any additional actions at all with screwdrivers and holes. The second installation option is similar in installation to the described option when using screws, only gluing is done rather than screwing.

Instead of holes for the holding line, special fasteners can be used, which are also glued to the bottom of the frame with double-sided tape.