How to properly wash with a washing vacuum cleaner. Rules for using a vacuum cleaner. Washing vacuum cleaner - an original design solution

Even if you clean your house every day, dust will still appear again. The question arises, how to make sure that cleaning does not take a lot of time? When cleaning carpets, furniture and other coverings a simple vacuum cleaner you will most likely not achieve a satisfactory result. To achieve this, you need to use a washing device, since it will clean many surfaces without much difficulty. So, how to use washing vacuum cleaner?

1. Today, all washing vacuum cleaners work on the same principle. So that you can start using the vacuum cleaner you need to pour water into a special tank. The containers in the vacuum cleaner, depending on the design, can be located either side by side or in different sections. There are washing vacuum cleaners in which the clean water tank can be located inside the used water tank.
2. At the first stage of cleaning, water is sprayed over the surface to be cleaned using a special nozzle. Then you need turn on the mode responsible for suction into the waste water tank previously splashed water along with dust. If the quality of the work done does not satisfy you, you need to add clean water and repeat the cleaning process again.
3. The washing vacuum cleaner can also work in dry cleaning mode. In this situation, dust and debris are sucked up and fall into a special bag, which also acts as a filter. After passing through it, the air is purified and goes out. This mode will help when cleaning surfaces that are sensitive to dampness and moisture, such as laminate.
4. If you need to clean the carpet or another similar surface, it is best to use special detergents, the effect of cleanliness of which greatly increases. This product is sprayed onto the surface under a certain pressure, knocking out small debris and dissolving dirt. The pressure of the air flow created by the vacuum cleaner allows you to clean the carpet to the full depth of the pile. After cleaning, the surface remains wet and needs to be dried, and to do this more quickly and easily, you can turn on the water collection mode.
5. In stores you can find many different cleaning products for washing vacuum cleaners. There are, for example, disinfectants that kill mold and mildew, foaming agents that are more suitable for cleaning carpets, and antistatic agents that create the effect of repelling dust.
6. Thus, a washing vacuum cleaner will help you clean with greater efficiency and a minimum of effort compared to a simple vacuum cleaner.

How to use the Thomas washing vacuum cleaner

Washing vacuum cleaner - universal remedy for dry and wet cleaning. This device effectively cleans various surfaces, including soft and wooden surfaces, from dirt and dust. He is for short term removes stains and debris, cleans floors, furniture and even humidifies the air. A washing vacuum cleaner removes dirt without streaks and dries the surface after washing in a matter of minutes.

A standard vacuum cleaner cannot cope with the listed functions and tasks. Washing equipment is indispensable for cleaning long-pile carpets. It will eliminate accumulated dust and at the same time preserve the texture of the product. Let's look at how to use a washing vacuum cleaner correctly.

Principle of operation and operation

The washing vacuum cleaner includes two tanks, one of which is designed for clean water with cleaning agent, and the second for collecting dirty water. Before starting work, pour water and detergent into the compartment. When the device is started, the water and the product are mixed, the solution moves through the hose and is distributed over the surface through the sprayer due to pressure.

The detergent composition moistens and washes contaminated objects, removes dirt and dust. After that dirty water is sucked back into the vacuum cleaner, into the second tank. Washing occurs evenly, and cleaned surfaces dry in a matter of minutes. This is how a wet vacuum cleaner works.

The device comes with several attachments that are suitable for different surfaces. These are special brushes for dry and wet cleaning of floors, for wet cleaning of carpets, for cleaning furniture and glass. Some companies, such as Thomas, even offer a plunger for cleaning plumbing fixtures.

In addition, you can find models with special antistatic brushes for cleaning your TV, computer and other equipment.

Brush attachments are great for blinds and roller blinds, soft foam attachments - for polished surfaces, turbo brushes - for upholstered furniture, special strips - for convenient cleaning of floors under cabinets, beds, sofas and armchairs.

On many models, you can adjust the power of operation and the volume of water that is supplied to the surface to be cleaned. In this case, for carpets, furniture and other soft surfaces choose maximum power so that the material does not get wet. After such treatment, such products are dried only in fresh air.

How to prepare a vacuum cleaner for work

• Before using the device, be sure to read the instructions and select a suitable cleaning agent;
• Water is poured into the reservoir, where detergent of the required dosage is then added;
• One end of the liquid tube is connected to the spray pad, the other end to the telescopic pipe;
• The hose is connected to a tube to which the nozzle is already attached;
• The hose is inserted into the device, the cord is pulled out and plugged into the outlet;
• Select the appropriate mode and press the power button;
• In a washing vacuum cleaner with a filter, you need to check the presence and cleanliness of the latter. In addition, you need to add a defoamer to the dirty water container.

What products to choose for a washing vacuum cleaner

Before using a cleaning vacuum cleaner, you need to determine what products can be used. You can choose a universal product that is suitable for cleaning various surfaces, for indoors and car interiors. It should be a high-quality product with reduced foaming.

There is no housewife who would refuse a vacuum cleaner with a wet cleaning function. This is a very convenient technique that provides really high-quality and fast cleaning of various surfaces.

It will be useful for those who own such a device to learn how to use a washing vacuum cleaner to achieve maximum efficiency his work and extend the life of the home assistant. The information presented in the article will also be useful to those who are just thinking about purchasing a multifunctional unit.

The algorithm for carrying out standard cleaning is known. First, the housewife collects dust and debris with a regular vacuum cleaner, then arms herself with a bucket of water and a rag to wash the floor. If the house has a washing vacuum cleaner, these two stages can be performed simultaneously.

The unit sucks up dust and small debris. After this, it delivers a stream of clean water to the floor surface, which it immediately absorbs and disposes of in a separate container. As a result, cleaning time is reduced, and its quality, according to reviews, is significantly improved.

A good washing vacuum cleaner is accompanied by detailed instructions, which needs to be studied, as well as a set of documents that confirm the quality of the device

Some make it possible to spray water in separate streams. This is useful where you need to deal with complex contaminants.

A great addition is the steam function. Such a unit is more expensive, but helps to cope with even the most complex contaminants.

Attachments designed for processing various surfaces improve the quality of cleaning with a washing vacuum cleaner. Often there is a compartment in the device body for storing them.

Inside the washing vacuum cleaner there are two tanks: with clean and dirty water. Before you start cleaning, the first one needs to be filled, and the second one should be clean and dry by this time. The device is serviced immediately after each cleaning cycle.

The cleaning liquid enters through the spray capillary and is almost immediately sucked into the main pipe and then transferred to the dirty water compartment

When purchasing a vacuum cleaner, you should pay attention to the volume and position of the tanks. Optimal size the container should allow the entire floor area to be completely treated without the need to add clean water to the device.

The location of the containers depends on the model and can be different:

• next to each other;
• one above the other;
• a tank inside another tank.

It is important to understand which container, “clean” or “dirty,” is removed first when servicing the unit. It is more convenient to start cleaning it after cleaning if you can first remove the tank with dirty water.

If, due to the large area or modest in size The model needs to be topped up with clean water; it is better to take a model with access to a “clean” container. Most often, manufacturers use last option, a tank in a tank, since it is considered the most convenient.

The vacuum cleaner usually comes with the necessary chemicals for wet cleaning: concentrated shampoo and defoamer, although low-foam formulations are also available on sale. When using them, you will not need a foam damper

The cleaning process also involves water, which must be dissolved in clean water. Mixing is usually done in a separate container and then poured into an appropriate container. The solution is supplied through a special capillary tube. It is usually located along the hose and suction pipe, inside or outside.

TOMAS vacuum cleaners are equipped with a special water box, which is used as a water filter during dry cleaning, and is designed to collect dirty water during wet cleaning.

Most often, the spray hose is located outside and is fixed on the surface of the telescopic tube with special clips. This design is typical for models that are designed for both dry and wet cleaning. When the spray elements are not needed, they can simply be removed.

During the cleaning process, the cleaning composition is sprayed onto the floor in front of the cleaning nozzle, then washed off with water, which is sucked up by the main pipe. Good power suction- most important characteristic washing vacuum cleaner. There are models with and without filters; the principles of caring for such devices differ markedly.

If the washing vacuum cleaner has several filter elements, after each cleaning they need to be removed, washed and dried, and periodically replaced with new ones.

Modern HEPA filters are good at keeping even fine dust inside, but they need constant cleaning and periodic replacement.

If a worn filter is not replaced in time, the suction performance of the vacuum cleaner will deteriorate and the overall quality of cleaning will decrease. Models that do not have filters do not have this problem.

Preparing the device for operation

Before you start cleaning, you need to prepare the washing vacuum cleaner. The procedure for using a specific model is usually described in detail in the instructions.

In general, you need to follow a number of simple steps:

1. Fill the “clean” reservoir with water or cleaning solution.
2. Attach the capillary tube to the spray nozzle and to the connector on the body.
3. Connect the capillary to the suction pipe with special clips.
4. Connect the suction pipe to the hose.
5. Insert the hose into the connector provided for it.
6. Pull out the cable and connect the vacuum cleaner to the power supply.

If the model is equipped with filter elements, then it should be added to the tank intended for collecting dirty water. Of course, before starting work, all filters must first be cleaned, dried and installed in their designated places.

A washing vacuum cleaner consists of many components that need to be connected correctly. Before each cleaning, check the integrity of the power cable and the tightness of the telescopic tube

Although the vacuum cleaner is called a detergent, it can also be used for dry cleaning. In this case, there is no need to pour water and detergent into the reservoir. This mode will be appropriate for cleaning upholstered furniture, carpets and other surfaces that absorb water.

Especially high degree cleaning is provided by washing vacuum cleaners equipped with a steaming function, but it should be remembered that not all coatings tolerate contact with hot steam well

You should not rely on your own intuitive understanding; before using the washing vacuum cleaner for the first time, you should definitely study the instructions compiled by the manufacturer. If the device has not been used long time, it is also recommended to refresh your knowledge regarding its proper use.

Actions after cleaning is completed

The floor is cleaned and washed, it's time to tidy up the washing vacuum cleaner.

Procedure:

1. Disconnect the device from the power supply.
2. Place the cord in the socket provided for it.
3. Remove the container with dirty water.
4. Pour out the water and wash the tank.
5. Rinse nozzles and hoses.
6. Dry all washed items.
7. Clean and dry filters and baffles.
8. Remove any remaining water from the “clean” tank and dry it.

Only after all parts have dried can you assemble the vacuum cleaner and store it. Separately, it is worth mentioning the care of filters. All filter elements must be removed, washed and dried thoroughly. Only after this can the filters be installed in place.

The HEPA filter needs regular and proper cleaning. It provides air filtration, retaining even very fine fractions of contaminants

If you collect a vacuum cleaner while the elements are even slightly damp, mold and mildew will appear on them, and this is dangerous for the health of the residents of the house. In addition, you need to regularly replace the filters with new ones, since even with regular and thorough cleaning, they gradually become clogged and become ineffective.

Normal resource HEPA filter Typically designed for thirty hours of active use. This time is usually completed in six months or less, depending on the intensity of use of the washing vacuum cleaner. In terms of dust protection, separator-type models without filters are considered more effective.

The built-in turbine creates an area inside the housing high pressure, which promotes the movement of all contaminants, including allergens, directly into the dirty water tank.

There is no need to add defoamers to such a vacuum cleaner, and its maintenance is a little easier, since there is no need to clean and replace filters. It should be remembered that a high-quality filterless vacuum cleaner must have, among other documents, an air purification certificate.

Example of using Karcher Puzzi

Karcher is one of the most famous manufacturers cleaning equipment. The procedure for using Karcher Puzzi will help you get a more accurate idea of ​​​​the use of these complex units.

After this, the following elements are connected in series:

• nozzle – fixed with a union nut;
• suction pipe;
• elbow - fixed with a union nut;
• suction hose;
• spray hose.

The collected elements are connected to a washing vacuum cleaner. In this case, the suction hose is first inserted into the socket on the body, and then the connection between this element and the spray hose is made with the elbow. Special attention attention should be paid to the junction of the spray hose with the elbow; a special coupling is designed for this.

In a separate container, you need to mix the detergent composition and clean water in the proportions that are recommended for this particular product. Better to use warm water(no more than 50°C) to increase cleaning efficiency. In this case, you need to make sure that the coating can withstand contact with warm liquid without damaging its condition.

If you plan to clean delicate surfaces (colored carpet, soft upholstery), first you need to test the detergent composition and the temperature of the working fluid in an inconspicuous area

The prepared solution is poured into a “clean” container up to the MAX mark. Now you can connect the vacuum cleaner to the power supply. Then press the SUCTION and SPRAY knobs to begin the cleaning procedure.

First, it is recommended to check the resistance of the coating to moisture and cleaner in some inconspicuous place. If the color and texture of the carpet remains unchanged, cleaning can continue. To supply the cleaning solution to the surface, a special lever is provided on the elbow of the washing vacuum cleaner.

The nozzle is moved along the floor covering in such a way that “paths” are formed with a slight overlap. The nozzle cannot be moved in any direction; only reverse motion is used. For periods when direct cleaning needs to be suspended, the nozzle can be hidden in the slot provided for this purpose on the handle.

After the coating has been treated with the solution, you can go over it again without splashing, as with dry cleaning. This will speed up the drying of the surface. When working with areas where there is heavy pollution, it is recommended to spray the composition and pause for about a quarter of an hour.

Before you start cleaning, you need to pour clean water with shampoo dissolved in it into the appropriate container. The concentration and method of dilution depends on the type of product and is indicated in the instructions for it

A short break ensures contact of the composition with dirt and increases cleaning efficiency. After this, you need to treat the surface again as with normal cleaning, and then again, but using only clean water.

When working with chemical-sensitive surfaces (multi-colored carpets, upholstery), you can reduce the concentration of the special product.

Particular care should be taken when working with jute surfaces, which are prone to color loss and deformation when in contact with moisture. Recommended for high pile carpets after cleaning. additional processing with a brush or broom in the direction of the pile. This must be done before the surface dries.

When the cleaning process is completed, first move to initial position SUCTION and SPRAY knobs, after which the vacuum cleaner can be unplugged. Now it is important to correctly carry out the maintenance procedure for the device. First, empty the “dirty” tank.

To do this, open the housing lid, take out the container and pour the waste water out of it. Do the same if this tank overflows during cleaning. First, of course, you need to unplug the vacuum cleaner and turn the switches.

Then you need to remove and empty the container, put it in place and perform the reverse operations: turn on the device and turn the SUCTION and SPRAY knobs to working position. At the end of cleaning, the compartment is washed with running water.

Now you should empty the “clean” container of any remaining liquid.

They do it like this:

• disconnect the vacuum cleaner from the network;
• relieve pressure inside; for this purpose, there is a lever located on the knee;
• disconnect the spray hose;
• lower the main hose into a container of water;
• turn on the vacuum cleaner and move the SUCTION handle;
• wait until the device pumps the liquid out of the container.

The next stage is washing the working elements of the device. The elbow is connected to the main hose and capillary. Now approximately two liters of ordinary clean water are poured into a “clean” container. There is no need to use a cleaning compound here.

Now you need to turn on the spray SPRAY. The washing process takes one or two minutes. Then the vacuum cleaner should be turned off. Once both tanks are cleaned, they need to be dried. The outside of the housing is wiped with a damp cloth, and its lid is left in the open position while drying.

If servicing a washing vacuum cleaner seems too difficult, you can choose a different type of unit. Good quality purges demonstrate

IN last years, All more people is thinking about purchasing a vacuum cleaner equipped with a cleaning function. Washing vacuum cleaners, along with dry cleaning, are capable of wet cleaning. Such devices can collect liquid, clean surfaces, upholstered furniture, curtains, glass, and humidify the air in the room.

With many useful functions, these vacuum cleaners are easy to maintain and handle. The market for these devices is represented by a large assortment of brands and models of any price category.

How the washing vacuum cleaner works

The operating principle of all washing vacuum cleaners is identical.

These vacuum cleaners have 2 reservoirs:

1. A special container is filled with water and detergents.
2. The second tank is intended for dirty water.

The spraying itself occurs using a capillary tube, which is attached to the handle and at the base of the nozzle. There is a special hole on the nozzle - a narrow nozzle through which spraying water is sucked in along with dirt.

Some models are equipped with an additional mechanical filter, which is designed to collect large debris.

The location of water tanks can be different:

• vertical;
• horizontal;
• one container into another.

Operating principle of washing vacuum cleaners:

• the tank is filled with running water;
• using a special nozzle, pure water sprayed onto the surface, after which the dust suction mode is turned on along with water into a tank specially designed for this purpose;
• To clean fabric surfaces, a special cleaning agent is added to the water (the proportions are indicated in the instructions). Pressure air flow, created by the device, makes it possible to clean carpets to the full depth of the pile;
• when using the unit in dry cleaning mode, debris is collected in a bag (if provided in the design) or a waste water tank, which also doubles as a filter. In this case, the air passing through the filter is cleaned. This mode is used when cleaning surfaces that are sensitive to moisture.

Peculiarities

One of the structural elements of the device is nozzles, they come in a set of 5 pieces:

• intended for washing floors and cleaning carpets;
• intended for cleaning upholstered furniture;
• necessary for collecting waste from hard-to-reach, narrow places;
• used for cleaning polished wooden surfaces;
• used for cleaning glass.

It is important to pay attention to the length of the power cord and the function of automatically winding and placing it inside the case.

Not less important structural element– barbell. A solid, non-separable rod is considered durable and reliable. Such a rod has a disadvantage in the form of inconvenience during storage and washing.

Collapsible rods are more comfortable during operation, but after several years of use, the likelihood of leaks at the joints increases.

Functions

Specified view household appliances has more extensive functionality, when compared with those not equipped with a wet cleaning function.

Functions:

1. Collection of large waste.
2. Collection of wet debris, moisture and liquids.
3. Air humidification in the room being cleaned.
4. Air aromatization.
5. Clearing clogs in sinks and bathtubs (additional nozzle required).
6. Cleaning dirt from floor coverings– tiles, natural stone, linoleum, upholstered furniture, carpet.
7. Cleaning vertical surfaces - glass, mirrors, curtains.
8. Cleaning the premises and removing pet hair.

Pros and cons of washing vacuum cleaners

The washing vacuum cleaner has big amount benefits, which include:

1. Ease and speed when cleaning dirt from horizontal surfaces;
2. Possibility of dry cleaning and removal of spilled liquids.
3. Humidification and air filtration are important for people suffering from allergic reactions and asthma. When cleaning, dust falls into a container of water rather than being sprayed.
4. Washing vertical surfaces and upholstered furniture.
5. Clearing small sewer blockages.

Despite the obvious advantages, these household appliances cannot be called universal.

The disadvantages of such washing vacuum cleaners include:

1. A washing vacuum cleaner will not remove dirt from surfaces covered with thick pile.
2. After cleaning a carpet or parquet, moisture will still remain.
3. Immediately after cleaning the room, you need to wash the vacuum cleaner itself. This procedure is mandatory and takes 15-20 minutes.
4. These units are bulky and heavy, which complicates the process of cleaning and storing the device, especially in a small apartment.
5. The cost is quite high.
6. Compared to regular vacuum cleaners – high costs electricity.

Do not use the device for cleaning wooden floors– residual moisture will get into the cracks wooden covering, and it will gradually swell and rot.

How to use a washing vacuum cleaner

To prevent it from malfunctioning, you must follow a number of operating and storage rules.

1. Before you start cleaning, you should inspect the appliance cord and hose for any mechanical damage. If damage is detected, it is not advisable to use a vacuum cleaner, and sometimes even dangerous.
2. When added to tank detergent you need to follow the proportions - they are indicated in the instructions and are individual for everyone.
3. During cleaning, do not cover it with anything, pull the power cord, over-tighten the cord and hose, or leave the vacuum cleaner turned on unattended.

After finishing the operation of the washing vacuum cleaner, you must:

• turn off the device and release the pressure into the water sprayers;
• drain dirty water from the tank;
• rinse the device with running water;
• dry the vacuum cleaner by removing the lid or moving it to the side.

1. In areas with flammable gases.
2. On open air.
3. For cleaning hot, burning or smoking objects.
4. For cleaning hazardous liquids and unknown substances.
5. Even with minor damage network cable, hose or other mechanisms of the device.
6. Non-stop for more than 1.5 hours.

It is important not only to use it correctly, but also to store it. The washing vacuum cleaner should be stored in a dry place, do not place other people on it. heavy objects, do not kink the hose. Some models are not designed to be stored vertically.

Precautionary measures

Like any other household appliance, a washing vacuum cleaner requires precautions when working with it.

Besides the fact that its mechanisms cannot be touched wet hands, the owner of the vacuum cleaner should exclude:

• contact of hair, clothing, various parts of the body with moving parts and mechanisms of the vacuum cleaner;
• presence of children and animals in the cleaned room;
• movement of the device itself along the power cord;
• closing the holes with foreign objects;
• contact of the cord with sharp, hot objects;
• clamp power cord door;

Malfunctions

Regardless of the brand and cost of the vacuum cleaner, a number of faults can be identified that are common to all of these devices.

1. During cleaning, water periodically stops flowing to the sprayer. IN in this case, the problem lies with the water pump, or the button responsible for spraying water. If this malfunction occurs, it is worth checking contact connections wires with a pump and a button that supplies water.
2. Can't wrap it up after cleaning electrical cord . This problem occurs due to a breakdown spring mechanism(or the spring has stretched), with the help of which the electrical cord is pulled into the vacuum cleaner. Eliminate this malfunction You can do it yourself if the spring has weakened, otherwise you should contact the service center specialists.
3. Does not turn on and a hum is heard, or noise or whistling is heard during operation. The reason for this is the failure of the electric motor bearing, which occurs due to overheating, moisture entering the electric motor, or getting inside the hose foreign objects. To diagnose and eliminate this breakdown, you must contact service specialists.
4. The washing vacuum cleaner works, but does not suck up dirt well, the motor of the device is noisier than usual. This problem occurs due to objects getting stuck inside the hose. You can remove such an object by attaching a hose to the outlet. If the design does not allow this operation, then the hose can be cleaned yourself, for example, with a long strip with a rounded end or a wire with a hook at the end.

1. Damaged or broken hose. This breakdown is common, it appears due to improper use: when cleaning, the hose is pulled or the hose is abruptly removed after use. Improper storage that causes the hose to become kinked can also lead to damage or rupture. It is worth remembering that the hose should not be pinched or bent either during operation or during storage.

A washing vacuum cleaner will become a real assistant for owners of houses and apartments with large area, especially if there is a variety of carpet, tile, and stone flooring available for pet owners.

Video and operating instructions for washing vacuum cleaner Zelmer 1600W

The Zelmer washing vacuum cleaner is great for cleaning the house due to its efficiency. Based on the needs of consumers, developers of household appliances regularly improve devices that can become excellent helpers in the home and apartment. Modernization occurs based on external data and, naturally, on internal components and functionality. The Zelmer 1600 washing vacuum cleaner is a device that meets all known international standards, and also has excellent quality, original design and only the best technical characteristics. Zelmer Aquawelt equipment is designed for wet cleaning and is equipped with an aquafilter, and the most important thing is that these models of household appliances are sold in almost 27 countries around the world. In order to start using the device, it is enough to study the document called the operating instructions.

Brief operating instructions for the vacuum cleaner Zelmer Aquawelt 1600W

Which device should I buy for both floor cleaning and dust collection? Modern Appliances- This multifunctional models, which can perform different kinds work, giving the owner only the pleasure of caring for the house. It is not scary to entrust such equipment with the collection of various types of dirt, from liquid-like dirt to construction dirt in the house. Zelmer Aquavelt 1600W works simply excellent, naturally, if it is assembled correctly.

Before you start using the Zelmer Aquawelt vacuum cleaner, you should read the instructions that come with it.

It can be used for:

• Collecting liquids of any kind from the floor and any other surface;
• Collection of fine dust after repair work;
• Washing upholstered furniture;
• Carrying out quick wet cleaning;
• Carrying out dry cleaning of carpets.

Zelmer Sirius 919 has exactly the same principle of operation. The devices are deservedly recognized as multifunctional, high-quality and in demand almost all over the world. The product is equipped with a number of attachments, which allow you to carry out various types of work.

The device includes a standard brush with extendable bristles for cleaning carpets and furniture, a cleaning attachment hard to reach places, a small brush, which is used for cleaning clothes and the surface of upholstered furniture, a turbo brush and on stone, marble or tiles.

If you purchase a Zelmer made and assembled in Poland, the design will fully comply with the stated requirements from the manufacturer for technical specifications And operational properties. Models Zelmer Profi 1600W and ZVC752spru 1500W are considered the most optimal options, however, there are also types with power up to 1900 W.

Instructions: how a washing vacuum cleaner works

Using a modern washing vacuum cleaner is practical, convenient, and extremely profitable. As a rule, all models of washing vacuum cleaners have one principle of operation, however, recommendations for use may differ. The design of the vacuum cleaner consists of a pair of containers that can be located horizontally and vertically relative to each other. One tank needs to be filled with clean water, and the second is designed to collect dirty liquid during the cleaning process.

There are models with small cassettes used for clean water, which are placed in the cavity of the waste liquid tank.

After using a washing vacuum cleaner, dirty water can simply be drained into the sink

To make the operating process even more pleasant and convenient, the devices are equipped with special wheels. As for the tanks, the one in which dirty water is collected has a large volume relative to the second tank, and therefore periodically you need to add water or a product, for example, shampoo, several times. In addition, the home cleaning unit is equipped with a device capable of supplying water to the surface that is being treated and collecting water after cleaning. Experts believe that the disadvantage of washing vacuum cleaners is that they have significantly large sizes, relative to standard household appliances. It will take much more time to prepare the device for operation and after this you need to carry out a series of actions in the form of removing all the liquid and drying the filter. In fact, those who use such devices believe that this is not a drawback, but just required procedures, since using washing vacuum cleaners is an absolute pleasure.

Each vacuum cleaner of this type works exactly the same, as it happens:

• Supplying liquid through a hose to the nozzle;
• Wetting the floor;
• Exposure to rarefied air on the surface being treated;
• Collecting water through a special channel into a container for waste liquid.

After such cleaning, the floor will be clean and there will be no stains or marks left. As a rule, it is impossible for the floor to remain dirty, since the power of the device is quite enough to process it. With the help of such structures you can clean tiles, linoleum, some types of laminate and carpeting, unless they have restrictions.

How to use a washing vacuum cleaner correctly

Before you start cleaning, you need to disassemble how the device turns on and check that all components are in place. After this, actions are performed that do not differ for both filter and non-filter models.

To use a washing vacuum cleaner, you do not need to have any special skills: you just need to fill the container with water and clean

Namely:

1. Clean water is poured into a tank specially designated for this purpose.
2. Be sure to fill in the cleaning product in strict compliance with the dosage specified by the manufacturer.
3. All the tubes that are included in the kit are connected into a single whole.
4. The hose is connected to a pipe that already has a special nozzle on it.
5. The device inserts a hose into the vacuum cleaner.
6. It is advisable not to pull out the entire length of the wire, especially if the room is small.
7. The device is ready for use.

If the model is filter, then the tank in which the dirty water is collected must contain a defoamer, which is extremely important, otherwise the equipment will simply fail. Be sure to check the degree of contamination of the filter fine cleaning, since if it is clogged with dust, it will lead to damage to the device. If there is an aquafilter, it must also be completely clean.

Zelmer is a unit that has many positive aspects, thanks to which it becomes so popular around the world. It is multifunctional. The products of this company have excellent equipment, since there are several brushes, and it is possible to purchase them additionally.

To disassemble Zelmer Aquawelt, just use a screwdriver

Land surveyor – excellent quality, full compliance with all sanitary standards, optimal cost, availability of spare parts, original design and many positive reviews.

Zelmer models of washing vacuum cleaners also have a number of disadvantages, but those who use them consider them to be completely insignificant. Heavy weight, which complicates the cleaning process if it needs to be done on several floors.

And further:

1. The parameters of the product may not be the most compact, and you will need to prepare a special place for storing it.
2. Detergent is not included.
3. Difficult to assemble and actually use.
4. The design contains a HEPA filter, which complicates the process of suctioning debris.

Vacuum cleaner Zelmer washing: instructions (video)

The disadvantages are actually not significant and sometimes they are not even noticed against the background of the mass of advantages. It is worth noting that purchasing Zelmer means becoming the owner of a wonderful unit that will deliver true pleasure from cleaning through excellent cleaning, creating a pleasant atmosphere in the house, and also simply because high-quality execution its intended purpose and excellent value.

Similar materials