How to properly glue wallpaper in the corners of a room. How to glue wallpaper in corners. Choosing suitable wallpaper for the kitchen
Often repair work is carried out by people themselves without the involvement of specialists. When decorating walls, the question may arise about how to glue wallpaper in the internal and external corners.
Possible difficulties
Bad wallpapering in the corners can ruin the whole appearance rooms
When covering corner sections of walls with wallpaper, you may encounter the following difficulties:
- Uneven surface. If there are crooked corners, wallpapering is a difficult task even for a specialist. It is advisable to pre-putty or, if necessary, plaster the surfaces.
- The divergence of the cut edges. The technique of cutting the wallpaper into the necessary pieces that reach exactly to the edge of the corner is often used. By applying this technology When gluing a corner, you may encounter the problem of a divergence of the joint between the canvases. As a result, a strip of wall is revealed.
- Too much curl. If there is even a slight curvature of the surface, the use of a large turn will lead to a vertical deviation of the wallpaper strip. As a result, all subsequent lanes will also be located on a slope.
- Poor quality gluing of the canvas. When gluing internal corners, a common mistake is not smoothing the strip inside the corner carefully enough. As a result, it forms free space, which over time will lead to the wallpaper coming off the wall.
Wallpapering external corners
If the edge of the panel that goes around the bend does not fit properly, several cuts are made on it diagonally and carefully pressed against the wall, making sure that no swelling is formed.
When pasting external corner the turn onto the adjacent wall should be approximately 3 cm. The wallpaper must be thoroughly coated with glue and carefully distributed over the wall surface. If non-woven wallpaper is used, then the glue is applied to the wall and not to the canvas.
If there are switches or sockets close to the corner, you must first remove the covers, remembering to turn off the electricity in advance.
Rules for gluing the inner corner
The seam where two panels meet end-to-end will become invisible after drying.
When gluing an internal corner, the wallpaper should be cut so that the fold onto the adjacent wall is about 1.5 cm. The glue is also applied to the wallpaper itself or to the wall, depending on the type of product. The place where the fold is in the corner should be pressed with a spatula so that there is no void left.
You can apply wallpaper correctly to internal and external corners yourself if you follow these simple rules.
Non-woven wallpaper is wallpaper made using non-woven cellulose non-woven material. Unlike paper counterparts, such wallpapers are easy to clean, allow you to hide even quite noticeable wall irregularities and retain an attractive appearance for a long time. And the process of gluing non-woven wallpaper is quite simple - the material is quite docile, does not “pull” either horizontally or vertically and practically does not produce “bubbles”. And even in such “problem” places. both external and internal corners, non-woven wallpaper is pasted without any problems - for this, when gluing it is enough to follow a few simple rules.
How to glue non-woven wallpaper on internal corners
The first thing that needs to be said about gluing non-woven wallpaper in corners (both external and internal) is You shouldn’t try to cover a corner with a whole sheet of wallpaper.. In other words, do not try to cover both walls adjacent to the corner with one canvas. Otherwise, there is a fairly high probability that the wallpaper will “lead” in the corner, and the resulting wrinkles will be almost impossible to smooth out without trimming, which will certainly ruin the appearance of the wallpaper. But even if this does not happen, the curvature of the corner (and unfortunately, most of the corners in our apartments are curved) will affect the position of the canvas, and since non-woven wallpaper is glued end-to-end, all subsequent canvases will also have to be glued out of level.
The correct technology for gluing non-woven wallpaper on internal corners is as follows:
- We measure the distance from the edge of the last glued canvas to the corner and add 5 centimeters to it. A panel of exactly this width will need to be prepared for sticking in the corner.
Since the angle can be curved, it is better to measure the distance at three points: the bottom, middle and top of the wall. For calculations, of course, you need to take the largest of the resulting values.
- When the panel of the required width is ready, carefully coat the wall and corner with glue for non-woven wallpaper. Please note that when gluing non-woven wallpaper, the glue is applied only to the walls.
- After the canvas is pasted, you should very carefully smooth the wallpaper in the corner and on the surface using a rubber roller or a dry cloth. next wall.
Using a rubber roller or dry cloth, smooth out the wallpaper in the corner and on the next wall. If the wallpaper “wrinkles” in some places, you can make several horizontal cuts at a distance of 5-10 centimeters from each other.
Please note that this canvas must be glued “overlapping” the previous canvas.
- When both canvases are pasted, it remains with a wallpaper knife and a metal ruler paint spatula make a seam trim. You can learn more about the “corner trimming” technology by watching the following video.
Video about corner trimming of wallpaper
It is very important to cut both wallpaper sheets “in one step”, since otherwise discrepancies may appear in the cut line.
To ensure that the cut is even and the wallpaper does not “stretch” under the knife? You need to periodically break off the dull tip of the wallpaper knife according to the marks specially applied to the blade.
- After trimming, all that remains is to remove the excess wallpaper. The top layer can be removed without problems, and the bottom layer can be removed by slightly unscrewing a small part of the top panel.
If you did everything correctly, then the panels form almost invisible joint, which remains to be carefully smoothed using a rubber roller.
Glue on external corners
External or external corners are not found in all rooms, but, nevertheless, they can be found quite often. The technology for gluing non-woven wallpaper to such corners is practically no different from the method of gluing internal corners.
The technology for gluing external corners is almost the same as the method for gluing internal corners. First of all, measure the distance to the corner from the outer panel and prepare new leaf wallpaper in such a way that after sticking they “turn” around the corner by no more than 5 centimeters. From the turning point closest to the corner, measure the distance for gluing the next sheet (roll width minus 1 centimeter). We glue the canvas “overlapping” onto the resulting fold, after which we trim the seam with a wallpaper knife and remove unnecessary parts of the wallpaper.
If the outer corner is fairly even (you can determine this using a plumb line), you can try to cover it with “one sheet”. But keep in mind that the level difference in this case should not exceed 0.2-0.4 centimeters. Otherwise, it is better to glue non-woven wallpaper using the technology described above.
As you can see, there is nothing difficult in gluing corners with non-woven wallpaper, so with a little practice you will be able to do this job perfectly. Good luck with your renovation!
In the article you can find the answer to the question of how to glue wallpaper in the corners. It is worth treating the finishing process with all responsibility; unevenness can be obvious, thereby spoiling the impression of a freshly completed renovation.
Step-by-step instructions for gluing internal corners
When finishing, the main problem can be uneven walls and the resulting folds in the wallpaper. You also need to take into account that with curved walls, the joints of the wallpaper may diverge.
How to glue an external corner (external)?
The protruding corner must be pasted over in the same way as the internal one, however, there are small differences that also need to be taken into account when working.
What to do if the corners are uneven?
Uneven walls common problem old houses. Before you start gluing finishing coat, it is advisable to carry out preparatory work and put the surfaces in order. If the corners are visually smooth and do not require overhaul, it will be enough to walk with a hard cloth, removing small irregularities and dust. If the unevenness is noticeable to the naked eye, then it is better to do a little work before you start gluing the wallpaper.
Features of gluing meter wallpaper
Wide canvases are convenient because they allow finishing with fewer seams on the surface. Gluing them is more difficult, but the result is worth it.
How to join in corners?
It would seem that such a trifle as gluing corners in a room can completely ruin the entire job if done incorrectly. And if the wallpaper also has a pattern that needs to be adjusted, then you should approach the finishing responsibly.
How to adjust the pattern in the corners?
It is important that the pattern is continuous and even around the entire perimeter of the room. To do this, you need to correctly combine the pattern and trim off the excess.
- The strips are also glued overlapping. An allowance is left on both walls.
- Using a plastic spatula, press the wallpaper to the corner.
- After gluing the second sheet, the wallpaper is trimmed according to the pattern. This method applies to wallpaper with small patterns. Larger designs may require trimming along the edges.
Before gluing, you must first prepare the material for work by spreading the coating on the floor and studying the pattern. The segments are cut off after selecting the pattern in height.
Features of trimming wallpaper in corners
In order to get a perfectly even seam in the corner, you need to properly trim the excess.
- After the wallpaper is pasted to the wall, a straight metal ruler is applied, it can also be a spatula or a rule. You can use a level to keep the cutting line straight.
- Acute stationery knife cut off the excess along the edge of the ruler, after which upper layer the wallpaper will come off.
- Carefully pry up the bottom layer of wallpaper and remove it in the same way.
- The canvases are coated with glue and pressed tightly to the corner. As a result, the coating fits tightly against each other.
Gluing wallpaper in corners is not that difficult, but it requires special care and precision. Today there is a finishing method that allows you to do the job without any joints at all, namely liquid wallpaper. They are applied in an even layer and do not require such difficulties as adjusting the pattern, width, accuracy in rounded places and other nuances.
The most in a simple way updating the interior of the apartment is wallpapering the walls. However, many people face some difficulties when performing work. The greatest difficulty is caused by gluing wallpaper in the corners. In these places, when carrying out repairs, many people make mistakes that spoil general form updated finish. It is enough to familiarize yourself with the algorithm, which prompts you to perform such actions correctly, and similar problems will no longer arise during subsequent repair work Oh.
Wallpapering in corner areas
The main difficulties faced by apartment owners when gluing walls finishing material, are uneven external and internal corners, often having uneven geometry. All this not only complicates the gluing process decorative material, but also significantly increases the repair time, which is unlikely to be included in the plans of any person.
Ultimately, the owners of the premises are forced to additionally treat the surfaces of the walls. Moreover, even subsequent use quality materials does not guarantee that the corners will be perfectly straight. This gives the impression that the work was done unprofessionally and spoils the overall appearance of the room.
Few people know how to properly glue wallpaper in the corners of a room. In order to correctly complete this process, it is necessary to follow a certain sequence of actions. Before doing this, you need to remember the following:
After the work approaches the next wall joint, the strip of wallpaper is trimmed so that it is glued to the adjacent wall only a few centimeters. Then the wall processed adhesive solution
. After the strip is fixed on the wall, it needs to be ironed rubber spatula or press with a roller. It is important that there are no folds left at the junction of two walls, even if there is an uneven bevel of the edge of the strip on the adjacent wall. If the material is very dense, then shallow cuts can be made on the inside of the finishing paper material. In this case, the canvas will better adhere to the joint surface of the walls.
Then, on the wall where there is a smaller part of the wallpaper strip, using a level or plumb line, draw a straight line from floor to ceiling. In this case, you should retreat from the corner by the width of the roll. Next, the glue is applied to the wall, and a piece of strip is applied to the existing line. In this case, its edge will overlap the uneven edge of the previous piece of wallpaper.
When both stripes are fixed, it is necessary to determine the place of the smallest overlap. It should be divided in half and from the middle draw a straight line along the entire height of the corner, then cut through it sharp knife or a blade.
The top piece of material must be carefully removed, folded back and the cut part of the bottom strip removed. Then both edges of the wallpaper are coated again glue, close and carefully smooth with a roller. The result should be a perfectly even angle, and there will be no sagging or cracks at the joint.
When gluing wallpaper in the corners, you need to wait some time after fixing it to the wall. Otherwise, the material, wet from the adhesive, will not be able to be cut smoothly. As you can see, there is nothing complicated in this process if you follow the algorithm
.
Such angles are much less common indoors. Wallpapering them is done in a similar way:
It is necessary to remember: even in the case of perfect even corners there is no need to strive to wrap the whole canvas. This is most often leads to the appearance of wrinkles and unevenness, and there is also a high probability that the material will swell and bulge unsightly. As a result, repair work will have to be carried out again, which requires financial costs. The whole canvas is wrapped only when wallpapering on window or door slopes.
Cutting off part of the canvas will not lead to high consumption wallpaper, so gluing wallpaper on the corners will not require increased expenses. Overall the job is not difficult, but there are minor nuances. If you take them into account, everything will be done correctly in accordance with your own requirements. If you don’t have confidence in your abilities, it’s better to entrust the work to professionals.
Renovating an apartment or house is a very complex and time-consuming process. And if workers do it for you, it is also expensive, since the price for the services of craftsmen is often the same as the cost of the material. Therefore, if you do at least some of the repair work yourself, you can save a lot. Many people successfully hang wallpaper on their own, and find nothing difficult about it other than gluing wallpaper in the corners.
Wallpapering the corners - responsible and important stage work
Even in very nice apartments there are bad angles. Not good because they are not perfectly even. What do the experts advise?
When gluing the outer corner, you need to ensure that the strip fits snugly against the wall.
Never glue an entire strip of wallpaper. If the angle is uneven, the strip will lie in folds and will not meet the other strip. Leave a protrusion of 1.5-2 cm around the corner, then the strip will lie against the wall. Be sure to use a plumb line if you are gluing thick wallpaper. Glue the piece with a slight overlap onto the adjacent wall so that it is as vertical as possible.
If there are switches or sockets close to the corner, you must first remove the covers, remembering to turn off the electricity in advance. Glue the fabric onto sockets and switches, then make cuts on the wallpaper and trim the circle slightly smaller size casing. After this, return the covers to their place.
When gluing a wall near a door, it is better to approach the doors from both sides. The strip of wallpaper that spans the door should be cut vertically to the beginning of the frame. It is attached along the edge of the wall. The lip should be trimmed and fit over the door frame.
How to properly glue wallpaper in corners: step-by-step instructions
- Step 1: Preparing the Corner
This step is performed long before the actual wallpapering at the stage of filling the walls. The corners of the room should be equipped with special plastic corners. They are attached to the walls with putty, and must be fastened very securely. After this, you can move on to decorating the corners of the room.
Don't cover all the corners at once. Having chosen the corner from which you will start, prepare a strip of wallpaper of the required length. Coat the area with wallpaper glue along the width of the cut strip (plus 3-5 cm), do not forget to apply glue to the plastic corner as well. When a section of the wall and a corner have been treated with glue, attach the wallpaper there. If you started gluing from left to right, you need to attach the left side to inside angle so that the strip is positioned perfectly even along its entire length.
- Step 3: leveling the wallpaper
Level the wallpaper well in the corners to visually hide existing defects
The wallpaper is rolled out with a special roller or spatula. After this, the next section of the wall is covered with glue, and the wallpaper is glued until next corner. How to glue the closing corner? The last strip of wallpaper should have a new strip associated with it. Roll the glue towards the corner, and when the wallpaper is glued to the inside of the corner, trim off the excess along the inside line of the corner with a utility knife.
How to glue non-woven wallpaper in corners
Non-woven fabric is a special material that consists of cellulose and non-woven fibers. This is wallpaper that is intended for painting, since it outer layer unstable to mechanical damage. Gluing non-woven wallpaper in the corners is much easier than any other wallpaper, since the glue is applied only to the wall, and the dry wallpaper is attached to it. Pre-decorating the corner of the room plastic corner, stick it in the same way as described above.
How to hang wallpaper with a pattern in the corners
With a clear geometric pattern on the wallpaper, distortion must be minimized
If the pattern on the wallpaper has vertical lines, its distortion will be especially noticeable in the corners of the room. And if the pattern is horizontal, it will be skewed in relation to the ceiling and baseboards. How to avoid such troubles? It's simple. Firstly, do not forget to make a slight overlap on the adjacent wall, and secondly, hide the existing joint at the top of the corner. Thirdly, try to paste wallpaper in the corners of the room so that the smooth edge lies exactly along the vertical line you drew (plumb line). In this case, the other edge is trimmed along the edge of the corner.
It is unlikely that it will be possible to completely avoid a shift in the pattern - a slight shift will most likely remain. But this is a drawback that only you will know about. After all, to detect it, you need to carefully study the corners of the room. If you follow all the rules, the wallpaper will lie vertically on the adjacent wall, which means that the distortion of the pattern will not be noticeable.