How to install blinds on plastic windows. How to install blinds on plastic windows yourself. Bracket mounting

Since windows are made to order and can have different parameters, it is very important to correctly measure the window when ordering blinds. It is necessary to measure the window height and width to the nearest millimeter. Remember that the length and width of the blinds should be slightly larger. For measurements, use only a steel tape measure; other types of tape measures (fabric, etc.) may introduce measurement errors.

It is very important to decide how you want to install the blinds: inside the window opening or outside. For the first option, the length of the blinds should be 1 cm less than the height of the opening, and the width should be 2 cm less than the width of the opening. If you are going to hang blinds over a window opening, then the length of the blinds should be 5-7 cm longer, and the width of the strip should be 20 cm larger than the width of the opening.

How to attach blinds

There are 4 main ways to attach blinds:

Mounting to the wall above the window

In this case, the window and slopes will remain intact; there are no clear restrictions on the width of the blinds (you can make them wider or narrower than the opening). Many manufacturers have begun to produce windows with already installed mounts for blinds. If you have installed a package that does not have such fastenings, then you will most likely have to use this particular method of installing blinds.

Before you begin assembling and installing blinds, you need to understand the structure of blinds. Horizontal blinds consist of several parts:

The top part of the blinds includes a rotating axis, rollers, curtain rod, brackets, control cord retainer, rotating mechanism and top cover.

The middle part consists of a ladder, lamellas (a thin plate of plastic or other material) and a plug.

The lower part includes the lower cornice and side cover.

Assembly of horizontal blinds

In order to assemble the blinds, you will need scissors, a screwdriver, screws and a drill. Take all the necessary tools and follow the instructions.

It is necessary to obtain and check the availability of all components for the blinds.

Take the top and bottom of the crossbar, which has a U-shaped cross-section configuration. It must be cut to the size of your window.

Make a small hole in the top rail for the control cord adjustment. All sharp edges of the hole can be covered with a plastic insert, which should be included in the kit.

After this, it is necessary to fasten the lower cornice with special clamps of the side covers along with a line of strung lamellas.

How to assemble horizontal blinds: video

Since you might not understand something from the text description, we recommend that you watch a video of how horizontal blinds are produced and assembled.

Installation of horizontal blinds on plastic windows

Fix the brackets (fasteners) on the top panel of the blinds.

Attach the blinds to the window and mark under the top fastenings.

Disconnect the brackets from the blinds and secure them with self-tapping screws to the window. After this, insert the blinds until they click.

Attach the adjusting bars.

Independent installation of different types of blinds on plastic windows is a troublesome process, but economical - on the one hand, and interesting and educational - on the other. Blinds in the house are a unique decorative element that allows you to transform plastic windows and decorate the interior as a whole. But there is one “but”. Blinds cannot be hung in two minutes, like cotton or tulle curtains. This requires a whole arsenal of knowledge and practical skills. Installing blinds with your own hands on plastic windows requires time, certain knowledge and skills. If you are new to this area, take your time with the activity, learn the basics of the design, installation methods and fastening rules, and only then go into battle.

The ideal option is to invite qualified specialists. The process will be quick, but not financially profitable. Doesn't fit? You don't know how to install blinds on plastic windows, but want to do it yourself? Then we suggest installing them yourself, having previously familiarized yourself with the basic rules and technology.

Blind mounting options

The design of blinds is a complex mechanism that requires not only a share of responsibility on the part of a specialist or “self-taught” person, but also a certain amount of knowledge, skills and abilities. There are many types, they all have common installation basics, but each of them has some nuances that are important to know about. If you take into account the subtleties of each type of blinds, they will last for decades without reminding you of themselves.

Before choosing mounting methods, pay attention to the condition of the walls and their architectural features.

You can attach blinds in one of three existing ways:

1. into the window opening;
2. on window sashes (for each separately);
3. onlay.

Which method should you choose? The choice depends mainly on the wishes of the owner, but also on the design features of the window.

What do you need to know about windows so as not to make mistakes?

Let us pay attention to a common mistake that occurs if you approach the issue of installing blinds on plastic windows incorrectly.

If you have installed horizontal blinds that look like a solid canvas on plastic windows facing the slopes, rest assured that you are guaranteed discomfort when opening and closing each of the sashes. This method is incompatible with blinds in the form of solid curtains, since each time you open a window or vent you will have to pull them up and then lower them again. This is a very troublesome task, especially in the kitchen, when plastic windows are opened very often for ventilation.

The solution is to fix the blinds not in the slopes, but on the window sashes.

How to install vertical blinds?

Installation occurs using brackets.

1. Make markings by marking with a pencil the places where you plan to hang them. It is desirable that the distance between them be from 30 centimeters to half a meter.
2. Fix the curtain rod in the brackets according to the instructions included with the curtains and additional elements.
3. When installed correctly in the brackets, a clicking sound is heard.
4. Do the same with the slats, installing them in the runners until you hear a click. The slats need to be hung sequentially if they have photo printing or a pattern.
5. Connect the lamellas with a chain both from the inside and from the outside.
6. Check the operation of the entire mechanism.

Installing vertical blinds has one, but very significant nuance. It is important to consider the width of the slats. If it measures more than 160 cm, then the number of brackets used must be increased to at least three.

Installation of horizontal blinds

A huge plus of horizontal blinds is that they can be installed on plastic windows of any shape, even roof windows are no exception.

Installation on a frame is an ideal option for horizontal slats, allowing you to open and close windows separately or simultaneously.

To install horizontal slats, you need to stock up on a screwdriver, a screwdriver and marking material (chalk, pencil or alcohol-based felt-tip pen).

Having decided on the mounting method, proceed to the following steps.

Find out the window sizes(measure width and height).

• If you are going to install blinds in the first way - in the window opening - you should subtract 2 centimeters from the height. This way you will achieve a result when the slats do not touch the window sill.
• If you chose the third method - attaching the blinds with an overlay - add 5 centimeters to the width, but always on each side. In this case, the height is determined by the desires of the owner.
• Installing blinds on windows (on each sash) is considered the simplest and easiest method of installation. The dimensions of the window must be measured taking into account the fittings, that is, so that they do not limit the window or touch it.

Remember: both plastic windows and blinds must function perfectly and efficiently. Therefore, it is very important to take accurate measurements before hanging them.

• Unpack the blinds. Assess their quality, inspect for defects, and check the components. Everything is in place?
• Place the blinds against the window. It is important that the body fits between the boundaries of the beads on both sides of the glass.
• Close the blinds tighter. They must be in the same plane as the window.
• Assess the overall situation. The blinds should be located at the top of the transparent area.
• Visually note the presence of a gap, which very often forms between the fastening elements and the window sashes. The size of the gap can be different and vary from a few millimeters to a couple of centimeters. They do not depend on the correctness of your actions; these are rather the costs of the design of the window and double-glazed window. Manufacturers foresaw the possible risk and, to correct the current situation, equipped the blinds with linings and special elements that allow them to achieve the required thickness and reduce the distance between the fastening elements and the window sashes.

Be sure to pay attention to the marks on the base of the linings. They can be of two types: R (from the English word right) and L (left). Right and left application respectively.

• Fix the gaskets until tight pressure is established. Then secure them in the gap between the fastening elements and the window field.
• Mark the fastening.

The geometric shape of the curtains is the main guideline for marking. Be sure to check that nothing prevents the window from opening and closing. Install an additional fastener where the cord is adjusted.

You can attach the blinds using one of two options.

1. Bead mounting. A very delicate process that requires care in choosing the length of the screws. An incorrectly chosen length is the first step towards depressurization of the glass unit, the result is a violation of the thermal insulation properties.
2. Profile mounting- a simple and safe process, but requiring care and clear actions.

Remember! The bead can always be replaced, the profile cannot.

• Install the structure

Install the blinds using long screws. It is advisable that you use the self-tapping screws included in the kit. The aesthetic appearance of the window after installing the curtains depends on them. This step must be taken with great care.

• Install the cornice, runners, slats

Place the decorative cornice on the mechanism and secure the plugs on the sides. Using a drill (diameter should be 3 millimeters), make a hole for the plastic “fungi”, they are located in the lower edge of the bead. This will allow you to install the guide line. After pulling it tight, secure it and cut off the excess.

• Control step - checking the functioning of the entire structure

What should you consider?

Do you want the installed curtains to serve for a long time, and their mechanism and fastening not to lose their original functions?

Tip 1. When buying blinds, try to ensure that all components are of high quality.

Tip 2. Choose the adjustment mechanism taking into account the convenient side for use.

Tip 3. Make sure that when the windows are fully opened, the blinds fold completely.

Tip 4. Turning the handle should not limit the mechanical impact on the elements.

Tip 5. Carry out maintenance in a timely manner.

Everything ingenious is simple. Now you are convinced of this. Installing blinds on windows with your own hands is not difficult if you have detailed instructions at hand. Choose a convenient method for yourself, use the instructions provided, and tomorrow the windows will “thank you.”

Installing blinds on windows is not such a complicated process; you can do it yourself. There are different mounting methods for different types of curtains and each of them has its own installation nuances.

Mounting methods

There are three types of fastening blinds: to the wall, to the ceiling, directly to the frame, and two ways - with and without drilling. The universal basis of any fastening is the cornice, which is attached to the wall, frame or ceiling in different ways.

With drilling

Fastening is carried out using self-tapping screws and brackets on which the cornice and fishing line are installed. Additionally, you will need a pencil, ruler, drill, and screwdriver.

First you need to make markings in the places where the brackets will be located. For reliability and accuracy, it is necessary to drill holes for the clamps in the marked places. Then, applying the brackets one by one to the PVC frame, use a screwdriver to secure them to the markings. Next, the cornice is installed and the entire structure is assembled.

No drilling

If you plan to replace blinds or other window decoration options in the future, it is not recommended to damage plastic windows. The holes from the screws will remain in the frame forever and will significantly spoil the appearance of the windows. In this case, it is easier to turn to a method that does not require drilling.

In this case, the brackets are attached in two ways:

• behind the top of the PVC profile on opening sashes(you can simply hang it like a hook);
• on double-sided tape, which can be glued without fear of leaving marks.

Mounting blinds on the balcony requires a special approach. The balcony design plays an important role here. The type of glazing determines the possibility of choosing certain blinds and the method of their fastening.

In general, almost all options are available for balconies. Particular attention should be paid to the type of blinds, since not all of them are universal for different types of windows.

For example, horizontal blinds are not suitable for a balcony with sliding windows, as they can become deformed during use or from strong winds.

The nuances of installing different types of blinds

Horizontal

The light-protective design with horizontal lamellas has become familiar, almost classic for window design. Advantages:

• Compactness. Installed directly on the window, leaving the window sill free. This saves space and allows you to place greenery on the window in favorable conditions.
• Light weight structure.
• Strength and rigidity of the lamellas, preventing deformation.
• Fire safety.

• Simple control mechanism.
• Special coating or impregnation against dust, dirt, odors and grease.
• Resistance to humidity and temperature changes.
• Various materials for making lamellas: wood, plastic, aluminum, less often fabric.
• Easy installation.
• Affordable price.

Some disadvantages are worth mentioning:

• When mounted on a frame, the angle of inclination is limited window sashes when opening.
• The slats produce a characteristic knocking or ringing sound when the wind blows. To avoid this, you need to purchase lower fasteners, which are not included in the kit and quickly become unusable.
• The structure is subject to repair in case of severe deformation of several lamellas, but it will cost the same as new blinds.
• Not suitable for balconies and loggias with sliding windows.

Vertical

Blinds, as the name already implies, are a simple and convenient light-protective structure consisting of longitudinal vertical plates.

They are distinguished from horizontal ones by:

• More aesthetic appearance. Horizontal blinds are more likely to be functional, while vertical blinds are decorative.
• Possibility to cover a large area with one cornice. Horizontal blinds, as a rule, consist of narrow slats and are designed for minimalistic decoration of small windows. Vertical models have different widths and easily cover the area of ​​​​large windows, arches and doorways.
• Variety of materials. They can be made of wood fibers, wood, aluminum, bamboo, plastic, woven and non-woven fabric, mirror, blackout, thread. The abundance of materials provides another advantage - variability of colors and textures.
• Modern and original window design, opening up more design possibilities.

• Simplicity of control mechanisms. Both mechanical and electrical are possible.
• Possibility to place photo printing on curtains due to the larger surface area and better material characteristics.
• Practicality. Larger slats are easier to wipe when necessary, which occurs infrequently. If, in the event of severe contamination, for example, in a children's room, the slats still need to be subjected to hygienic procedures, this will not take much time - they can be washed by hand and in a washing machine.
• Possibility of installation on non-standard windows(triangle, trapezoid, arch, bay window).
• The structure is subject to repair. To replace this or that part, you do not need to call a specialist; the repair is simple enough to do it yourself. You can replace the lamellas one at a time without dismantling the entire structure.

Rolled

Roller blinds and roller blinds are solid canvases, often made of textiles, but other materials are also possible, which, like horizontal blinds, are rolled up.

The height can be adjusted by fixing the curtain with a weighting agent on the bottom strip of the canvas.

There are different types of roller shutters: with an open drum (for mounting directly on the window) and with a decorative cornice; “mini” for installation on each frame separately and “roll-cassette” for covering the entire window.

There is an opinion that roller blinds are the most budget-friendly and practical option for window design, but this is not entirely true.

Of course, roller shutters have their advantages: a variety of natural and synthetic fabrics, colors and patterns, ease of care (wet cleaning is allowed) and operation, the ability to fix the curtain at the desired height, special impregnations against dust, moisture, high temperatures and glare, compatibility with other types of curtains.

A roller blind is convenient if you need to hide a room from the sun, or decorate a window with beautiful tulle so that from the street you cannot see what is happening inside.

But with so many advantages, curtains also have significant disadvantages:

• The budget price is a misconception. Yes, a medium-sized curtain made from a common material will not cost much, but it will look boring. In order for the window design to be complete, it is necessary to consider additional decor, and this increases the cost several times.
• Roller blinds in the bedroom, office and rooms with high windows need electrical control. Electric drive designs are expensive, and some manufacturers also produce noise.

• It is impossible to make custom-made curtains from certain textiles. You can only choose specific products of a certain brand, since the range of fabrics for the production of roller blinds is very limited: translucent, textured, reflective, perforated, blackout.
• The maximum width of roller blinds is 280-300 cm, that is, covering a large area with one cornice, for example, a panoramic window or balcony, will not work.
• There may be problems with installation not on the wall, but in the window opening, since the bobbin is wider in width than the curtain itself. There will inevitably be gaps on the sides of the window openings. Ceiling or wall mounting is preferable.

Pleated

This type of blinds is similar to both horizontal and roller blinds. The design consists of a control mechanism (chain or electric drive), weights, and pleated fabric that resembles accordion bellows. The range of materials, colors and textures is very diverse.

Peculiarities:

• They close from top to bottom, like classic canvases, from bottom to top, or from both sides at the same time. In this case, the degree of density of the “accordion” can be adjusted, thus closing either the upper, lower, or central part of the window.
• Suitable for curtains windows of irregular shape.
• The optimal solution for attic rooms, attic, ceiling and inclined windows.
• “Opening”, the canvas compactly gathers into a fold and hides inside the cornice.

• Convenient for installation on all types of windows and double glazed windows.
• Various mounting methods and control mechanisms (manual and electric).
• The woven fabric is washable.
• The curtain fabric can be made of two types of fabric at the same time, which makes it possible to regulate the degree of transparency, darkness, and sun protection.
• Easy installation you can do it yourself.

Kinds

• Classic. In appearance they are most similar to horizontal blinds, however, they can also be vertical. Made from fabric, paper or plastic. Designed to darken the room, protect against heating by the sun's rays, and zone the interior space of the room.

• Inclined. A type of pleated specifically for windows that are located at an angle in the attic or ceiling. Their peculiarity is in a specific assembly system, which does not allow the canvas of any material to sag when at an angle. Mostly inclined models are produced with electronic control.

• Corrugated. This type is a vertical and horizontal double pleat. As a result, the folds look smoother, neater and denser. Corrugation made of plastic and paper in this design absorbs a significant part of the heat and protects from bright light.

• Arched. The most flexible canvases that take any shape, like a paper fan. A good solution for rooms with non-standard window shapes (arches, trapezoids, triangles, sloping windows).

• "Day Night". The fabric of such blinds consists of two layers of fabric: light, light-transmitting fabric for daytime use, and thick, dark fabric for protection from the bright sun during the day and prying eyes in the evening.

Cassette

Such systems involve either the use of horizontal slats or a solid fabric, but are not horizontal blinds or roller blinds.

They differ in the types of cassettes (angular, round, flat), controls (various types of mechanical and remote), and the materials used (plastic, textiles, bamboo, aluminum).

Their main feature is their design, the special structure of which makes it possible to fix the blinds at a minimum distance from the window glass. This prevents deformation, sagging, wrinkles and unevenness, and completely opens the window sill.

Advantages:

• Compactness. Cassette blinds take up minimal space, leaving owners the opportunity to use their imagination and organize additional window decoration or leave the window sill as a functional surface.
• Simple and clear type of control.
• Long service life. Special impregnation protects the canvas from dust, grease, dirt, moisture, and abrasion.
• Ease of hygiene procedures. Cassette systems do not require special care. It is enough to wipe their small surface area with a damp sponge and soapy water once every few months.

• A variety of designs for interiors in any style.
• The tight fit of the canvas to the surface of the glass protects equally well from heat and cold.
• Possibility to install the system yourself.
• A variety of materials - from light window decoration to total blackout protection.
• Possibility to combine blinds with curtains, tulle, lambrequin.

Measurements and tools

The final result depends on how correctly the measurements are taken. Even expensive, beautiful models will not look good on the window if there are gaps in the opening or the edges of the slats constantly ride up against the wall.

It is important to pay attention to the following points:

• For the most accurate indicators A steel tape measure and metal screws are used.
• The resulting numbers cannot be rounded., accuracy must be maintained down to millimeters.
• When ordering blinds The width parameter is indicated first, the length parameter – second.
• Not a single standard window opening has absolutely ideal geometric shapes, therefore measurements in height and width must be made at least at two points.

Horizontal

If you plan to attach blinds to the movable half of the window, you will need to measure the gap between the glazing beads and add at least 30 mm, which will prevent gaps from appearing in the structure. The height of the blinds is equal to the height of the window sash. For installation inside a window opening, measurements are required at three points in height and width, since openings are not always absolutely proportional.

The width is identical to the wide side of the glass plus the thickness of the rubber seal. The length is identical to the height of the window (including elastic bands) with a margin of 1 cm. To install the cornice, an additional 30-40 cm will be required to the slopes and hinges. The control chain is 2/3 of the window height. When choosing to fix the cornice on the wall, the width parameter increases by 10 cm, the height is measured from the point of attachment of the brackets to the floor at random.

Vertical

When installing in a window opening, you need to determine the width at the top of the arch and subtract 20 mm. To determine the height, compare the height of the left and right sides of the arch, subtract 1 cm from the smaller value. For wall mounting, you need to add at least 10 cm to the wide side of the slope. The length of the slats can be any, but it is recommended to retreat 2 cm from the edge of the blinds to the floor. Ceiling installation involves determining the height (to the floor or window sill) minus 2 cm, it is recommended to increase the width of the arch by 100+ mm.

Rolled

To install canvases to the wall, only one measurement is required - from the edge of the window sill to the markings for the brackets, and the width can be up to 300 cm. In the window arch, roller blinds are installed after measuring the width, from which you need to subtract 4 centimeters, and the length of the canvas is equal to the height of the window minus 15 mm.

Pleated curtains similarly do not require a professional approach to taking measurements and installation.

How to hang it on the wall yourself?

Installation work on window decoration requires certain skills and experience, but if you want to try it yourself, you need to take into account some of the nuances and features of this work. Installation of blinds begins long before preparing the working surface and a set of tools.

The first step of this process is an informed decision regarding the type and variety of blinds, material, color and texture, depending on the functionality of the room.

So, it is more advisable to choose vertical blinds for the living room that let in light, for the bedroom - automatic electric roller blinds made of blackout fabric, and for the kitchen, where cooking smells and food combustion products are constantly in the air - plastic blinds that do not absorb grease and dirt.

The second important point is the correct marking. A lot depends on it, including how easy the installation process will be.

If all the architectural features of window openings are taken into account by specialists when ordering blinds from them, everything will go easily and smoothly without the help of professional installers. It is also important to consider whether it will be possible to open the window after installation, how the light protection devices will work, and whether there is a risk of their deformation.

The installation of blinds must be carried out exactly with the markings and subsequent verification of the functionality of the structure. The most important point here is the choice between fastening - with or without drilling. It is also necessary to provide for the type of control.

For low windows, an excellent solution is one of the types of mechanical controls. Magnetic, automatic (electric) control with an electric drive is suitable for roof and inclined windows, windows in the bedroom.

Ceiling installation instructions

• First of all, you need to mount the blinds, assemble the brackets and install them on the reel. Then this structure must be fixed to the ceiling in order to mark for fastening.

• The second step is to attach the brackets with adhesive tape at the top of the frame and the string tensioner at the bottom. It is not necessary to pre-attach them with tape, but it is advisable to eliminate problems with subsequent drilling of holes for screws. After installing the guide string, the curtain itself is mounted into the mechanisms.

What is the best way to install automatic electric window blinds?

Automatic blinds are the most convenient way to decorate a window yourself.

They are attached in three ways: to the ceiling, to the frame with drilling, to the frame without drilling. In all cases, the fastener is a cornice with or without a decorative facade.

The brackets on which the structure is supported are fastened with self-tapping screws, hung or glued with double-sided tape.

Special adhesive tape, despite its apparent impracticality, is fixed very firmly, so it is important to correctly apply the markings for installing the brackets. Once they are glued, moving them will be very problematic.

Installation procedure:

• Preparing tools. You will need a stepladder, a set of screws from the kit, a building level and drawing supplies, a drill, and a screwdriver.
• Applying pencil markings for installing brackets. To securely fix the fasteners, it is recommended to drill holes for self-tapping screws at the same stage.
• Attaching the brackets in a suitable way (with or without drilling).
• Installation of cornice.
• Installation of slats. To do this, you need to pull the control cord on which the fastenings for the slats are located so that they are in the desired position. Then fix all the slats on the hooks of the fasteners.

How to attach cassette tapes yourself?

You can also install cassette blinds yourself. Before installation, you must read the instructions, make sure that everything is complete, and prepare all the necessary tools: a screwdriver, drawing tools, a screwdriver, a drill, cotton pads or a small piece of cloth, and a degreaser.

When everything you need has been collected, you can proceed to the first stage - degreasing the glazing beads. Then you need to remove the side covers of the box, lift it to the top of the frame, focusing on the guide protrusions, drill holes for fastenings, and secure with screws.

You can use a screwdriver for this purpose, or you can perform the process manually using a Phillips screwdriver.

Once the box is installed, you need to secure the covers to the sides. After this, you can glue the guide strips to the degreased frame. The guides should be several centimeters below the angle of the bead.

We hang aluminum curtains and blinds on sliding windows

For installation you will need a set of tools: wire, drill, Phillips screwdriver, screwdriver, drawing supplies.

The instructions for installing blinds on sliding windows contain a list of items that are carried out step by step:

• Draw a marking line for installing brackets. It must take into account the distance between the clamps and the control mechanism, between the brackets (from 60 cm) and to the extreme areas on the blinds (25 cm). For large blinds and significant weight, it is recommended to use intermediate fasteners.
• Drill holes for installing dowels on the surface to which you plan to attach the brackets. It is possible to use blinds on plastic windows without drilling.
• Installation profile.
• Fixing the top rod of the blinds on the brackets. It is important to remember that the blinds at this stage are already assembled.

Working with aluminum options on inclined surfaces requires a little more effort and skill.

How to secure the bottom?

The easiest and most affordable way to do it yourself is to mount without drilling using double-sided adhesive tape. Suitable for tilt-and-turn mechanisms on windows.

Performed step by step:

• Degreasing of frame areas and fasteners, which will be connected with adhesive tape.
• Marking fastening roller shutters.
• Installation. The chain mechanism can be installed on any convenient side.
• Assembly brackets.
• Marking for fastening brackets. To do this, you need to install them on the assembled roller blind, install it on the window without fastening, mark with a pencil the places for the adhesive tape, and remove the curtain.
• Applying adhesive tape on the back surface of the brackets, mounting on a window.
• Installing the guide string against sagging. It is attached to the “ear” of the top bracket and the weighting of the curtain, and at the bottom it is fixed in the tensioner, which is installed on the frame.

This video shows how to hang horizontal blinds with your own hands.

It is not always convenient to use curtains. In some cases, blinds are more practical and convenient. They make it possible not only to protect yourself from immodest glances in the evenings, but also to regulate the level of illumination during the day by turning the slats (plates). We will talk about how to install blinds on plastic windows in this publication.

Designs and installation methods

There are two types of blinds for windows - vertical and horizontal. Vertical slats are usually made of plastic or special dense fabric, cut into strips 10-15 cm wide. Less commonly, you can find slats made of aluminum or synthetic threads.

The slats of horizontal blinds come in plastic, wood and metal. Regardless of the type and material, they consist of a cornice and slats. Cornice is a plastic or aluminum U-shaped profile in which the controls are located and from which the lamellas are suspended. Lamels are horizontal or vertical stripes/plates that actually cover the opening. In order to be able to open and close the blinds, there are controls - chains or threads.

In horizontal models there is also a control rod connected to a rotating mechanism. By rotating the rod, the angle of inclination of the lamellas is changed. This is how you can change the amount of light and the “degree of transparency” of the window. If the slats are placed vertically (almost), they completely block the view. When positioned horizontally, they hardly interfere with the view, but there are many other positions.

Installation of horizontal and vertical blinds

When installing blinds, you need to attach the cornice. To fix it, the kit includes specially designed brackets. These brackets are attached to the window or wall, and the cornice is simply put on them (until it clicks).

There are several ways to install blinds on sash windows:

You will have to decide on the method of installing the blinds before purchasing: the size of the canvas depends on this. So the type of installation must be chosen before taking measurements.

We take measurements

You need to decide on the type of blinds (horizontal, vertical) and the method of installing them (on a wall, on a ceiling, in a sash window, in a window opening) before purchasing. And even before you start measuring. Because different installation methods require different sizes. Only with correct measurements will it be easy to install blinds on plastic windows.

Another important point: Each window must be measured separately. Sometimes it just seems like they are absolutely the same. Believe me, there is a difference. You also need to write down the measurement results and sign which specific window you measured and which sash it is. Accurate and detailed records will help avoid confusion during purchase and installation.

In the window opening

Although the appearance of the products is different, when measuring there is no difference between horizontal and vertical models. If you are going to install blinds in a window opening, you need to subtract 2 cm from its width on each side. You can subtract 1-3 cm from the height of the opening. Such gaps are needed so that the canvas hangs freely in the opening and the lower edge of the slats does not rub against the window sill.

Please note that you can install blinds on plastic windows “into the opening” not flush with the edge of the opening, but deeper - near the glass itself or by stepping back 5 or more centimeters from the edge. If the opening has a trapezoidal shape, the height/width of the opening will be smaller for the glass, so we take careful measurements. And also, in this case, it is better to put marks for installation when measuring. Then you will know exactly where you will need to install blinds on plastic windows so that their dimensions fit perfectly.

On the ceiling or wall

Here the measurements depend on your desires. The length of the blinds can be up to the floor or just up to the window sill. Moreover, depending on the type of installation chosen, the slats can cover the window sill or not. So the length is whatever you like.

This is wall mounting. When mounted on the ceiling, the length will increase, but how much is up to you

The width of the blinds with this installation method is wider than the window opening. How much wider depends on your desire, but the minimum offset is 5 cm on each side. But if the window is in the same plane as the wall surface, you will need additional brackets, which are not included in the package: the slats must be placed at a distance of at least 5 cm from the glass surface so that they do not interfere with opening the doors for ventilation.

On the doors

When installing blinds on a multi-leaf window, there are two options - install one device on each sash or order one long one for the entire window. Usually the first option is chosen - it makes it possible to open and close the shutters with the blinds lowered. If you choose this installation method, you will need to measure each sash and record the results. The doors may be different, so be careful.

The width of the blinds when installed on the shutters is taken to be 3 cm wider than the glass. When hanging, the lamellas overlap the profile by 1.5 cm. This is convenient and does not interfere with opening/closing windows. The length depends on the location of the fastener, but usually it is 5 cm longer than the height of the glass.

Once again we draw your attention: we measure each sash!

How to install blinds on plastic windows: attach to a wall or window opening

The first step is to apply markings. We install brackets in the cornice. We place them on the right and left so that they do not interfere with the operation of the blinds. The installation height depends on the selected product length.

We attach the curtains, mark with a pencil on the wall the places for installing fasteners in the brackets. If we are installing horizontal blinds (they are light and create almost no load), it is enough to install one screw/dowel. Vertical ones are heavier, so you need to install all the fasteners from the kit.

There is a second way. At the selected level, use a building level to draw a horizontal line, try to avoid tilting - this will affect the blinds (skew). Place the bottom of the bracket against this line and use a pencil to mark the holes for drilling. If the length of the cornice is more than 2 m, an additional bracket is required to increase the rigidity of the structure, which is attached in the middle.

When attaching to brick or concrete, drill holes in the wall or ceiling at the marked points. A drill or a hammer drill - whoever has what is available. The diameter of the drill depends on the size of the dowels. They usually come included, but you can supply your own.

We insert spacer dowels into the finished holes and carefully hammer them in with a hammer. We install the brackets, fasten them with screws or nails (if dowel-nails are used). We install the cornice on the brackets and insert the plugs on the sides. For horizontal blinds, attach a rod (handle) to control the swing mechanism. To do this, install a special hook (included) directly into the mechanism itself, and attach the tip of the rod to this hook.

Installation of horizontal blinds on PVC window sashes

With this installation method, the blinds are attached with small self-tapping screws (included in the kit) to the window profile. They must be installed so that they do not interfere with the handle turning. Be careful: if you drill too close to the bead, you can damage the glass unit. Therefore, in this case, correct measurements are very important.

Installation step by step

The procedure is as follows:

Having to drill holes in a window frame can be intimidating, but it's no big deal. In case of incorrectly made holes, the unsuccessful ones can be filled with sealant. White silicone, not acrylic (acrylic quickly turns yellow). The performance of the windows will not be affected. What can be dangerous is getting into a double glazed window. Then it may crack. But this is not fatal either - it can be replaced, although it will not be cheap.

We install the lower clamps

But that is not all. To finally install horizontal blinds on plastic windows, you need to drill a couple more holes - for the clamps (also called anti-wind). These are additional fastenings at the bottom of the opening window sash. The lower edge of the blinds is tucked into them. They do this so that when ventilating, the blinds do not hang down, dangle in the wind, or knock over objects on the windowsill.

Don't hang out...

We install the clamps like this: we try it on, pulling the blinds down a little, mark the fastening points, drill holes, and install. We tuck the bottom bar into the installed clamps. Now, even with a draft or an open shutter, the blinds will not dangle. The only thing you need to watch out for during installation is not to get caught in the glazing bead (this is a long strip that runs along the glass unit and holds it in place). It is necessary to drill a hole in the frame itself, stepping back at least 1 cm from the edge. Otherwise there are no problems.

No drilling

There is also a way to install blinds on plastic windows without drilling the frame. This method is only available for those blinds that are hung on opening sashes. In this case, they are simply hung on plastic mounts/brackets, which are placed on the frame from above. To prevent them from moving, a strip of double-sided tape is attached to the back of the bracket. After removing the protective film, you can glue it (but you don’t have to fix it).

These L-shaped plastic brackets are not included, but can be purchased at a store or company that sells horizontal blinds. This method is convenient by simply dismantling the blinds, which is convenient if they need to be repaired or washed.

Assembly of vertical blinds

Vertical blinds are installed exactly as described above. The difference is that the slats are installed after the cornice (the guide along which the runners move) has been secured. For convenience, before attaching the slats, you can use an adjustment cord to turn the sliders so that the slots in them are perpendicular to the cornice. Next, we simply snap the slats into the runners, inserting the strip until it clicks. So, we fasten all the slats one by one.

If the slats are made of fabric, then after installing them do not forget to insert the lower weight. Next, we attach the lower connecting chain to the lamellas.

The installation of vertical blinds is complete.

At first glance, it may seem that installing horizontal blinds seems like an easy and simple process. However, it is worth considering that windows and walls in houses are most often uneven, so installing horizontal blinds requires appropriate experience and knowledge.

If you are confident that you can install the blinds yourself, then you must adhere to a certain installation technology.

To do this, you will need tools such as a Phillips screwdriver, hammer, hammer drill or impact drill, drills and drills. The first thing you need to do is decide on the method of installing horizontal blinds - attach them to the frame or in the window opening, to the wall or to the ceiling.

Only after choosing the mounting location and taking correct measurements can you begin to install the blinds. In order for the installation of horizontal blinds to be carried out reliably and efficiently, it is necessary to use fastenings - brackets or brackets, which are included with any blinds.

Brackets can be used to securely mount blinds on almost any surface.

Video: Blinds for plastic windows. Measurement and installation.

Technology for installing horizontal blinds:

1. Mark the places where the brackets will be attached. When marking, you need to take into account that the brackets should not touch the latch and the control device. Using a ruler and level, mark the placement of the fasteners from each other at a distance of more than 60 cm and less than 25 cm from the uppermost sections of the blinds.

If the width of the blinds is large, you can use intermediate fasteners to increase the reliability of the installation. One of the brackets must be placed near the lifting and lowering device, since in this area the blinds device is subject to the greatest load.

2. Consistently drill holes in the wall and insert dowels into the markings. Screw the brackets with screws. It is very important that the screws and dowels are completely similar to the fastening, wall or ceiling material.

If you plan to attach horizontal blinds to a PVC window frame, then it is not necessary to drill the window profile, since there are special brackets designed for metal-plastic windows. It is worth noting that this fastening method may only be suitable for a swing-and-turn sash.

3. The blind curtain rod is installed on the mountings.

4. The top bar of the blinds is placed on the brackets and locked with a lock. Moreover, horizontal blinds must already be assembled.

The installation of inter-frame horizontal blinds has some differences from the technology presented above. Such blinds should be installed in the internal space between the glass panes.

That is why, when installing them, the brackets are first attached to the upper cornice. Then, by crimping, the flexible adapter is attached to the rotary rod.

The control device is brought inside the room through a pre-drilled hole. Only upon completion of these operations can you proceed to attaching inter-frame horizontal blinds to the frame.

Video: How to install horizontal blinds yourself