How to heat water in a plastic pipe. Effective methods for defrosting a plastic water pipe underground. A plastic pipe is caught in the frost, what to do?

How to heat water in a plastic pipe.  Effective methods for defrosting a plastic water pipe underground. A plastic pipe is caught in the frost, what to do?
How to heat water in a plastic pipe. Effective methods for defrosting a plastic water pipe underground. A plastic pipe is caught in the frost, what to do?

Freezing is common in winter water pipes in private homes. If pipelines are laid underground, then most often the reasons are insufficient depth and insulation of pipelines in combination with stagnation in the pipes. If pipes located in the walls freeze, this phenomenon may occur due to very severe frosts. In any case, the home owner needs to know how to defrost water pipes in a private home. Below we will look at how to eliminate ice jams in metal and plastic lines.

It is not enough to know how to defrost a pipe underground. First you need to find the immediate place of freezing. This can be done in a simple and proven way. The water supply to the water supply should be shut off. After this you need to unscrew any plug connection, which is located after the tap. A plumbing cable is inserted into the opened hole. It is gradually introduced into the pipeline until its end hits the ice plug.

This will be the freezing point. To mark its position on the outside of the pipe, the cable can simply be attached to the ground to the same length as it entered the pipe. This is where you should look for the freezing point. So in a simple way can be found Right place in a pipe made of any material.

Methods for defrosting pipelines

The material from which it is made is of no small importance when defrosting pipes. The methods of influencing the pipeline depend on this.

Defrosting metal pipes

Let's look at how to defrost metal water pipes in a private house. Usually they run underground, so there are certain difficulties in digging a trench in winter, although it is also possible to locate them on open areas. After the pipeline is exposed, it is affected in the following ways:

  • Use an open flame. For example, from a gas burner or blowtorch. You can also make a fire on a frozen section of pipe;
  • Use welding transformer. One wire from it is connected to one frozen section of the pipe, and the second wire to the second. The ice plug melts very quickly;
  • The pipes are poured with boiling water after wrapping them with rags.

Important: While defrosting the pipeline, the water taps must be kept open. This is necessary for free flow of defrosted water from the pipes.

It is easier to defrost a sewer pipe, since all the melted ice will go down the drain, but with a water supply the situation is the opposite. The released water will have nowhere to go, so it is advisable to disconnect the pipe from the taps or at least open the taps.

How to defrost plastic pipes

Plastic pipes require more careful handling due to the lower strength of the material. Let's look at how to defrost water in a plastic pipe that is in plain sight:


We looked at heating the open section of the pipeline. How to defrost a tap plastic pipe underground? There are also several ways to do this:

1. Submission hot water. The plastic pipe is disconnected from the tap. In some large container, for example, a barrel, water is heated. A smaller diameter hose is used that fits freely into the pipe. It is pushed inside the pipe until it reaches the frozen area. After this, hot water is supplied to the pipeline. This can be done using a pressure pump.

The melted water will gradually flow out of the pipe along with the supplied hot water. The end of the hose should be pushed further and further until all the ice plug is removed. After this, water will flow under strong pressure.

Tip: Plastic or metal-plastic pipes should be pre-insulated in open areas to avoid the occurrence of additional ice jams.

2. Use of a steam generator. The plastic pipe is disconnected from the taps. A special hose from a steam generator with a special nozzle at the end is inserted into it. It is injected until it reaches the frozen area. Steam is supplied through the hose into the pipe, quickly melting the ice. As the frozen plug melts, the sleeve moves deeper into the pipe. With such a device, the question does not arise of how to defrost a pipe located in a wall or underground.

3. Use of electricity. This method It works on the principle of heating water with a boiler. To do this, you need to stock up on a thick two-core wire of sufficient length. The veins are separated. Each of them is released from the insulation and then twisted. The result is two thick twists, located at a distance of 1-2 cm from each other. The possibility of connecting them to each other must not be allowed to avoid a short circuit.

The wire is pushed inside the pipe to the plug location. After this, the end of the wire is connected to the mains. Ice melts by heating it with electric current. Wherein plastic walls do not heat up, since only the current-conducting water is heated. As the ice melts, the wire moves further along the pipeline.

4. Hydrodynamic cleaning. Using a hydrodynamic machine, you can eliminate any ice plug in the pipe. Hot water is supplied into it under pressure through a special nozzle, which helps to destroy the ice in a very short time. As the plug breaks down, the hose with the nozzle moves further along the pipe. It should be noted that such equipment is located mainly in specialists due to its high cost.

5. Another method of defrosting a water supply is shown in the photo.


Freeze Prevention

We looked at how to defrost polypropylene pipes(and pipes made of other types of plastic) or metal pipelines. Equally important is preventing pipes from freezing. The occurrence of this unpleasant situation can be avoided if you adhere to some rules:


We have looked at the main ways to get rid of ice blockages in water pipes. However, it is much easier to prevent water from freezing in pipelines than to fix problems that arise later.

Almost every private house has drainage and sewer pipes through which water and wastewater are supplied and discharged. Since this system is the property of the residents, in the event of any breakdowns or problems, they often have to deal with everything themselves. One of the most relevant and unpleasant situations problem that we have to deal with is the freezing of water in pipes in winter period. It is very important to be able to defrost pipes correctly so that the ice does not break them during melting, compromising the integrity of the entire water supply system.

Peculiarities

For water supply in a private home, both metal and plastic pipes can be used, but some and others are not protected from freezing in winter if the installation process was carried out incorrectly. The most main reason The fact that water freezes in a pipe underground in cold weather is due to insufficient deepening of the water supply system. If the installation technology is carried out correctly, then the entire system is located at a level where frost does not reach.

Due to the fact that the main pipelines have a large diameter, they do not freeze even in winter, because water moves through them all the time. Home systems are installed using pipes with a diameter of 20 mm or more - 32 mm. It is important to deepen such thin elements well so that frost does not reach them, but this is not always possible, so you need to know what means you can use to insulate pipes to protect them from the cold.

If all the recommendations have been followed, but the water still freezes, then in this case it is necessary to keep the system turned on all the time so that water always flows through the pipes in at least a thin stream. This is quite expensive, considering the cost of water, but you will not need to waste time, effort and money on defrosting the entire system.

In order to avoid having to carry out heating work on water pipes every year, it is important to prevent all possible problems still at the stage of laying the entire network.

During installation, it is important to follow these rules:

  • The depth of the trench should be greater than the level of soil freezing, which is typical for this region. There are relevant SNiP standards that will help you design a water supply system correctly.
  • When choosing a location for pipes, it is important not to lay them next to reinforced concrete products, because their thermal conductivity is greater than that of the soil.
  • If the installation is carried out under the foundation, then the pipes are insulated from reinforced concrete using a large layer of thermal insulation, which works best with mineral wool.
  • When planning a water supply system underground and on its surface, it is best to use pipes with a diameter of 50 mm, because thinner products freeze much faster.
  • When choosing a material for pipes, you should give preference to polymer products that can increase the size by several millimeters, which saves them from cracking during freezing and freezing.
  • To ensure a calm winter, you should lay a heating cable near the pipes that will support optimal temperature and will prevent the system from freezing.
  • If the house is used only in the summer and is empty in the winter, then it is important to drain all the water from the system so that there is nothing in the pipes during frosts. This will protect them from freezing.

What will you need?

If a pipe that supplies water or discharges wastewater is frozen in a private house, you must first determine the location of the blockage in order to eliminate it and not aggravate the situation. The most simple option The search will be to use an iron cable, which is inserted into the water supply, which was previously shut off and immediately untwisted under the tap at the junction of the structure. It is important to choose the longest cable because problem area may be either at the beginning of the system or at its end.

Once the plug has been discovered, you can excavate the affected area of ​​the pipeline and accept everything necessary measures for defrosting. If the structure is old and the pipes are metal, then the easiest way to heat the water inside is with current, for which a welding machine is used. But this method is no longer suitable for a HDPE pipeline. For them, the use of external means brings little results; a different approach needs to be taken.

The most effective, but expensive, would be to use a hydrodynamic machine, which can deliver a stream of water at such a speed that ice and some other substances melt from such an impact. Only a professional can work with the device, because it is important to know the technology and follow the work algorithm. If you need to quickly eliminate the problem, but do not have the necessary skills and equipment, you can simply call a specialist who can easily do everything necessary to restore the water supply.

Another method of heating a pipe involves a steam generator, the operation of which looks like this:

  • pour 2-3 liters of water into the container;
  • connect the heat-resistant hose to the place where the safety valve is located;
  • insert the hose into the pipe to the place where the plug has formed;
  • turn on the device and wait for the result.

Work should only be carried out in correct sequence and it is better to have assistants with you, because after removing the hose from the pipe where the ice was, a fountain will simply flow. This water must be collected in buckets, which must be prepared in advance. You can prepare more rags.

If you don’t have a steam generator, it doesn’t matter; a boiler will do for defrosting the pipes. To use this option, you need to prepare a wire; it must be copper, two-core and have a cross-section of 0.5 mm, and its length must be equal to the pipe. In addition, you also need steel wire, the diameter of which is 3 mm. Copper wires are stripped to 60 cm, and the second wire to 1 cm from the cut. Separate turns are made on each wire so that there is no contact, otherwise a short circuit will occur.

Electrical tape copper wires screwed to the steel and the whole thing is immersed in the pipe. In this simple way you can build a homemade boiler. It must be connected to the network to warm up the pipe, which will push out the plug from the heat. Once the problem is solved, the boiler is turned off and pulled out, and the pipe is closed. When the system starts again, everything works as it should.

Defrosting of pipes can be done welding inverter. This is a wire that connects to the pipe where there is icing and heats it up. It is important to work with the device correctly and not overheat it by giving different voltages. After just ten minutes of such exposure, the ice turns into liquid and the plug dissolves.

Heating water pipes in the event of ice blockage is one of the most effective option. For an iron pipe, the method of external influence is suitable, and for a plastic pipe - internal. The means by which it is convenient to deal with icing can be anything, and everyone chooses what they like and can afford, the main thing is that there is a result, but it is best not to lead to such situations by correctly laying the water supply and insulating it well.

How to warm it up?

In order to warm up a metal-plastic water pipe in which water has frozen, Several techniques can be used, including:

  • Exposure to hot water, for which the structure is wrapped with foam rubber or rags and very hot water, almost boiling water, is poured inside. This option is quite simple, but it is effective for pipes inside the house. In the case of underground ice jams, this method can break through the barrier for up to ten hours.
  • Using hot air, for which you need to have a hair dryer or heating device. The icing area can be heated by any of the devices for two or more hours, it all depends on the degree of freezing of the water inside. It is not difficult to do such work, but it is important to carry out all activities carefully, because from high temperature the pipes may become warped, further exacerbating the problem. Efficiency this method not too large, because with large energy and heat losses, the real result does not come soon.

  • Heating using thermal conductivity. It consists of winding pipes with cable, which is used in a heated floor system. When everything is ready, the resulting structure is connected to electricity and begins to heat the pipe itself. The work process lasts approximately three hours and allows you to prepare only those pipes that are above ground and in the house. Wires for heated floors are quite expensive, so buying them in order to defrost the system once is unprofitable due to their high cost.
  • The process of heating the pipes inside can solve the problem quite effectively. To work, it is important to have access to the problem area in order to pour hot water into it using a special device that forces liquid under high pressure, but you can also use a device that looks like a boiler. The work proceeds slowly, the problem is completely resolved in at least three days. It is prohibited to use this option for those sections where the pipes run vertically. The system must be in a horizontal position to ensure functionality.

If you have to deal with plastic pipes, then you can deal with defrosting them yourself, the main thing is to know what exactly needs to be done. For those pipelines that are located underground and the system is a network of turns and various bends, then all the previously listed options will not be able to help. The most the best option in this case there will be a welding machine that needs to be connected to different ends of the pipes and turned on. If you don't have the right equipment, you can just use hot water.

To do effective remedy To defrost pipes, you need:

  • find a rigid hose or small-diameter plastic pipe;
  • place the hose or pipe in the water supply and move until it hits the ice;
  • pour hot water or brine;
  • for the water that will form from the ice plug, you need to place a container;
  • As soon as the problem area is completely eliminated, you need to turn on the hot water in the tap and thoroughly clean the system.

If they were laid metal-plastic structures, then to defrost them you need to do a number of actions:

  1. To find the problem area, simply probe all the pipes. The freezing point will be much colder than the rest of the surface.
  2. The icing area is covered with rags and all water taps are opened. It is necessary to ensure that there is a supply of hot water.
  3. The pipe surface is treated gradually and is used immediately. cold water, that's why it's hot. This is important in order not to damage the structure with a sudden temperature rise.
  4. The melted water will begin to come out of the pipes through the taps that were opened earlier.

If there is no desire to carry out such operations annually, or even several times during the winter, it is worth quickly organizing insulation of the area, which is especially susceptible to freezing.

In cases where water freezing occurs in areas inaccessible to humans, for example, under a foundation, then You can deal with problematic situations using a number of measures:

  1. You need to purchase a barrel, a pump and a hose with oxygen. You need to fill the barrel with hot water, the temperature of which will constantly rise.
  2. Insert the hose into the pipe and push until it hits the ice.
  3. You need to open the tap and connect it to a hose that goes into the barrel. If you don’t have one, you can use a simple bucket.
  4. The pump starts, with the help of which hot water is supplied to the pipes to defrost the ice. From time to time the pump must be turned off to drain the accumulated water.
  5. As soon as the problem goes away, the hose must be removed and the water in the pipeline drained.

If the problem concerns the sewer system, then you can deal with it if you know how. Typically, sewer pipes do not freeze because the water used is usually warmer, but in very severe frosts this is possible.

To combat ice plugs in the sewer, you can:

  1. Light a fire in the place where the collector is located. This option will be effective if the pipes are not far from the surface. The flame must be maintained for as long as possible in order to be able to heat the ground, and with it the sewer system.
  2. Usage table salt. A homemade but very effective method is to place a large number of a solution of concentrated table salt, which will not freeze even in severe frost, and the salt will begin to dissolve it upon contact with ice.
  3. You can use an electric cable, which should be run until icing occurs through the toilet or inspection hatch. Once the device is installed, turn it on to the network.
  4. You can use the inspection hatch of the septic tank, where a watering hose is inserted through the outlet garden plants. It needs to be advanced to the place where ice is expected to be present, and then hot water from the water supply must be poured inside. The process must be continued until the ice is completely gone.

In case of severe frosts in winter time and water freezing in pipes, you need to know how to cope with the situation. First of all, it is important to understand what material the pipes you are working with are made of, how deep they are laid and a number of other nuances, after which it will be much easier to choose correct option combating ice jams.

If problems with pipes are discovered in a private house, namely their freezing in winter, then you need to know some secrets in order to prevent such phenomena or skillfully deal with them.

To prevent such phenomena, you should:

  • Install water supply and sewerage pipes lower than the frost, and this is at least a depth of 120-140 cm. In case of problems with such a deepening, the pipes are carefully insulated.
  • By using pipes that are large enough in diameter, you can avoid their rapid freezing. The optimal size would be 50 mm.
  • To avoid stagnation of water in the system when arranging it, it is worthwhile to provide an angle of inclination so that it flows faster into the source.
  • When laying pipes, you should stay away from beams and foundations, the thermal conductivity of which is higher than that of the ground, which poses a danger to the pipes. It's worth doing if possible good insulation, if there is reinforced concrete nearby.
  • If the water supply is in non-residential premises where there is no heating, then it is important to additionally insulate it, for which it can be used mineral wool, glass wool and foam.
  • Living in regions with very harsh winters, when installing a water supply system, it is better to lay a cable nearby that will heat the pipes. Its advantage is that it itself determines the moment when it needs to turn on and off, but there are also manual models.
  • When choosing a pipe, you should give preference to polyethylene rather than polypropylene, because they withstand the process of freezing and defrosting ice well.

There are a number of other tips that will help protect the system from freezing or deal with it more effectively:

  • To protect the pipeline from freezing, it is worth studying the temperature regime of the region and lowering the structure a meter below the level where frost usually falls. This will allow you to forget about any problems with water in cold weather.
  • If pipes freeze where the ground intersects with open space, then a regular hairdryer can help, but especially difficult cases– construction.
  • If problems with pipes arise every year, then you should set the goal of redoing the system rather than constantly struggling with the consequences.
  • When the freezing is very serious or difficult to solve on your own, it is best to call a professional who can remove the ice blockage without any problems.
  • If you manage to deal with ice on your own, but at the same time you have to constantly clean the system by running water, it can be collected in special containers and then used for household needs.

For those who still use metal water or sewer pipes, ice plugs can be dealt with using terminals that are attached to the problem area, after which a current begins to flow, which heats up the pipe and the ice inside begins to melt. If freezing occurs in the pipe leading directly from the toilet, then one of the options may be to heat the water directly in the plumbing, for which you will need a heating element or a boiler. Metal pipes They also warm up using a blowtorch, for which you need to make a trench at the location of the sewer and heat the pipe with the lamp, going from bottom to top. Work is being carried out from outside cesspool or a septic tank, if there is one, to allow the unhindered release of water after melting.

July 22, 2016
Specialization: Capital construction works(laying a foundation, erecting walls, constructing a roof, etc.). Internal construction work (laying internal communications, rough and fine finishing). Hobby: mobile connection, high tech, computer technology, programming.

I have told many people about manufacturing technologies many times engineering systems in private homes. And all the time I drew attention to the fact that pipelines must be laid below the freezing point or carefully insulated. However, from time to time people contact me with questions about how to defrost a plastic water pipe.

I remember a time when a neighbor in the country called me in mid-January and tearfully asked me to fix the water supply. As it turned out, he planned to spend his anniversary outside the city, and upon arriving at the site after a long stay in warm countries, he was faced with the fact that water was not flowing from the taps. And all the complex electronics that provide water to the cottage don’t work either.

As it turned out, the culprit was an ice plug that clogged a metal-plastic pipe laid underground. And since he could only sign business papers with his own hands, he had to call me for help.

Of course, we dealt with the problem, and I turned out to be the most honored guest at his holiday. I decided to tell you about how to defrost plastic water and sewerage pipes. Perhaps the instructions below will provide you with invaluable help. Especially when a reliable plumber friend is not nearby.

Causes of pipeline freezing

In my practice, I have very rarely met people who make or order modern utility networks (water supply, sewerage) from steel pipes. Plastic is more common.

And I think this is correct, because the price of polymer pipes is decreasing all the time, and operational properties such solutions have always been at their best:

  • plastic pipelines have an attractive appearance;
  • pipes are not subject to corrosion throughout their entire service life;
  • mount utility network as simple as possible without the use of electric welding (maximum - a soldering iron);
  • pipes do not conduct electricity and do not accumulate static electricity.

The only thing that cannot be avoided under any circumstances is the danger of the liquid in them freezing. However, I know for sure that people encounter this problem only in cases where they entrusted the installation to an illiterate engineer.

Only such a person can lay a water supply system at insufficient depth in the ground or fail to insulate the engineering system. As a result, you arrive at your dacha to celebrate your birthday, and nothing flows from the tap. Sadness.

To prevent this from happening, it is necessary to dig a sufficiently deep trench for the water supply and sewerage pipes. The average depth of soil freezing in the Moscow region is 1.4 meters. However, this indicator depends on many other factors, so to determine exact value It’s better to contact specialists or use special cards with tables.

By the way, many people ask why they don’t freeze central water pipelines in cities. I will answer without reserve. There, the flow of water does not stop around the clock, so the liquid is in motion and does not turn into ice.

And at the dacha, the pumping equipment is turned on only from time to time. Therefore, it is imperative to take measures to insulate water transport pipes.

Pay special attention to insulation and deepening drainage systems where water flows at low speed. Otherwise, a traffic jam will form and you will have to decide how to defrost the plastic sewer pipe. This task is difficult and far from pleasant.

If for some reason it is not possible to dig a ditch of a suitable depth, it is necessary to wrap the pipes in thermal insulation materials or come up with systems for heating them. Or use both options.

If you know that your pipes are poorly insulated, and at night they promise very severe frost, leave the water on overnight to ensure flow in the pipe.
In this case, the likelihood of ice appearing is significantly reduced.

But it often happens that people return to issues of pipe insulation only when they are already faced with freezing water. There’s nothing left to do here; we’ll have to melt the ice. I’ll tell you about this now.

Defrosting water transport communications made of plastic

underground

First, let's look at how to defrost a plastic water pipe underground. This, in my opinion, is the most labor-intensive and time-consuming process. Especially in winter, when not only the water in the pipes froze, but also the ground itself where they were laid.

The simplest scheme is as follows:

  1. It is necessary to light a fire over the place where the plastic pipe passes. You can use wood or coal, and also light car tire. The latter will burn for a long time, but will emit black, smoky smoke. Take this into account.

The advantage of this method is that not only the water in the pipe must heat up, but also the earth itself must thaw. And we need this in order to move on to the next point of our work.

  1. I then suggest digging up the pipe to check if it is damaged. This will be easy to do, since the fire will soften the ground and it will be easier to swing the shovel.
    Usually, high-quality plastic pipes are not broken by ice, so there is no need to repair anything. The main thing is not to break the pipe during excavation.
  2. After making sure that the communications are intact, I recommend insulating the pipeline thermal insulation materials or pave . If this is not done, then I personally will not give a guarantee that after filling the trench with earth, the water in the pipe will not freeze again.

If you ever encounter water freezing, I recommend redoing the engineering system in the summer. After all, your friend will not always come to the rescue in time and dig up this pipe. It will be necessary to either deepen the trenches or insulate the water transport system along its entire length.

By the way, someone once told me that they insulated pipes with empty plastic bottles. The scheme is like this:

  • you dig a pit and check the pipe;
  • take more plastic bottles, you wrap the plugs so that there is air inside;
  • you line the pipe with them;
  • you cover everything with earth.

The point here is that the air inside has a low thermal conductivity coefficient and will prevent the water in the pipes from freezing.

What can I say? In my opinion, you will spend more time collecting bottles than working. Better go to the store and buy basalt shells. It will be clean, neat, efficient and not very expensive.

And to everyone folk recipes I've been coming here less and less lately. Unless he himself is confident in their effectiveness.

Another way to remove ice blockage is to use hot water. I see several disadvantages here:

  • you will have to disassemble the plumbing system somewhere in order to fill it with water;
  • the pipe will remain uninsulated and the liquid may freeze again at any time;
  • the method will not work if the ice is on long distance from the place where you are going to pour boiling water.

Nevertheless, sometimes I resorted to this method. To make it more effective, I'll give you a few own advice, which were formed during the work:

  1. If your dacha is connected to central water supply, do not turn off the taps. Additional pressure from the central water supply can help break the plug.
  2. If water comes from pumping station(i.e. well or well), the equipment must be turned off. Otherwise, you will ruin expensive electronics as the water will drain from the pipes.
  3. You can tell that the blockage has been removed by the fact that the water poured into the pipe will all flow out.

Another proven method that I have sometimes used to defrost pipes. It must be implemented carefully, as you may get hit electric shock. Nevertheless, I will describe the technology, in case you have no other way to fix the problem.

The scheme is like this:

  1. I'll take it electrical wire, I separate one core from the other and remove part of the insulation. Then I roll one wire into a spiral. I do the same with the second core, but the twist needs to be placed a little behind, about two centimeters.
    It is very important here to ensure that these twists do not move during the work and do not touch each other. This may cause a short circuit and electric shock. So be very careful to secure the ends of the wire.
  2. I insert the tool prepared in this way into the pipe until it hits the ice plug.
  3. After this, the wire must be connected to electrical outlet. Heating of the liquid inside the pipe will occur due to the potential difference across the twists. The walls of the pipe will not melt; the water temperature will not rise to this level in any case.
  4. As it thaws, you need to move your device deeper until the patency of the engineering system is completely restored.

Remember that thawed water must be drained at all times, otherwise it may freeze again.

There are also special devices for thawing pipes. It's about about steam generators, autoclaves and hydrodynamic devices. It is not necessary to buy them; it is enough to rent the necessary unit from a specialized construction supermarket.

The work proceeds as follows:

  1. Steam generator. It is necessary to place the device hose inside the pipe and release steam under pressure. Considering that the temperature of the environment is much higher than the boiling point of the liquid, the defrosting process will occur very quickly, and the plastic will not be damaged.
  2. Autoclave. Steam is also used here, but the operating principle is somewhat different. First, water is heated in a container until steam is formed from it. Then a hose is inserted into the water pipe (up to the ice plug), the second end of which is connected to the autoclave.
    As the ice thaws, the hose must be moved along the pipe until the water flows in the direction you want.
  3. Hydrodynamic machine. It destroys ice not by temperature, but by a jet of liquid pumped under high pressure. As a result, the traffic jam can be removed very quickly and efficiently.

And if someone advises you to just bend the wire and break through the ice, you don’t need to do it. So, with a high degree of probability, you will damage the plastic shell of the pipeline itself, but not the ice plug.

Overhead

As you understand, defrosting plastic pipes laid openly (for example, in a basement, pantry or other unheated room) is much easier. Here you will not need the help of a specialist at all. Especially if you follow my advice.

The easiest heating method is a hair dryer or other similar heat source. By directing the air flow to the engineering system, you gradually heat the walls of the pipes, which give off their thermal energy water. And the ice melts.

By the way, the hair dryer can be replaced with a regular heater, which is placed near the pipe.

You've probably seen how metal pipelines are heated with blowtorches. So, this heating method is absolutely not suitable for plastic. The polymer has very low temperature melting (about 140 degrees), so a flame from a gas or gasoline burner will melt not only the ice, but also the pipe along with it.

Naturally, mandatory stage any defrosting involves insulating pipes or installing heating elements that support required temperature liquids. I offer several options to choose from:

  1. Take mineral mats and wrap them around the pipes. It is imperative to protect all this from above waterproofing material to avoid moisture and some kind of protective cocoon. A roofing material that will cope with both tasks is suitable.

  1. Buy and attach special foam shells to the pipes, basalt fiber, foamed polyethylene and so on. The simplest option. They are installed quickly and easily, without the use of special tools.

  1. Wrap the pipe with heating electric cable. This method is suitable for both heating ice and preventing its further formation. You just need to make sure that the cable is constantly connected to the electrical network.

It’s best to wrap the pipes with cable and then with insulation. A combination of these methods will provide you drinking water at any time of the year, regardless of the outside temperature.

Defrosting a sewer pipe

I’ll tell you separately about the method of removing a cork from drain pipe external sewer system of a private house. This is the problem that most residents of private country houses face.

So, to fix the problem you will need:

  • rigid steel wire;
  • hydraulic level (dense polymer flexible tube);
  • Esmarch's irrigator;
  • a bucket for collecting dirty liquid;
  • hot water.

I fixed a similar problem like this:

  1. I removed a piece of sewer pipe, opening access to the pipe connecting the internal and external sewer systems of the house.
  2. I aligned the steel wire and attached a hydraulic level to it with electrical tape, through which hot water will flow into the pipe.
  3. Then he put this entire device into a sewer pipe, and attached Esmarch’s mug to the opposite end of the pipe.
  4. After that, using an improvised pump, he began to pump hot water inside, gradually moving the device inside the pipe.
  5. Excess water and thawed sewage poured out through the neck. I collected them in a pre-set bucket.
  6. As soon as the water stops flowing out, it means the plug has thawed and you can assemble the engineering system.

As in the case of plumbing, to avoid freezing of the drain, you need to lay pipes at the required depth or insulate them with heat-insulating materials. It’s better to spend time and money on this in the summer than digging through waste in the winter, on the eve of your birthday.

Regardless of the chosen defrosting method and the method of laying pipes, I will give a few more tips that must be followed when thawing pipes:

  • if you know exactly where the ice plug is located, you do not need to heat this particular section of pipes from the middle;
  • to ensure the outflow of melted water, it is necessary to open the water tap;
  • I recommend starting the defrosting procedure from the consumer (supply tap) to the source of water intake (vertical riser).

Conclusion

There are a lot of ways to defrost pipes, and everyone who has encountered a similar problem knows their own way to defrost ice. I would be glad if you would share it with our readers by describing it in the comments to this article.

And I suggest everyone to watch the video in this article, where you can find many other tips regarding the operation of the engineering systems of a residential building.

July 22, 2016

If you want to express gratitude, add a clarification or objection, or ask the author something - add a comment or say thank you!

There are both external and internal methods of influencing a frozen area. Naturally, the effectiveness and labor intensity of each method is different, as is the time to achieve a positive result. When preparing to defrost plastic pipes, you should be prepared for the fact that the length of the frozen section inside the building, as a rule, is no more than 3-5 m, and underground it can reach more than 20-30 m.

How to defrost a plastic water pipe underground? You can also use the hot water method to defrost underground water pipes. Only for its implementation in field conditions A longer length of tubing will probably be required.

More effective option The way to warm up a plastic pipe in the ground is to heat water to the state of steam and supply it under pressure to the place of freezing. To heat the liquid, you need to use a sealed vessel with a pipe at the top. A flexible and durable oxygen hose or hydraulic level tube is suitable as a supply tube.

How to warm up a plastic pipe of an internal polymer water supply? From the outside it may seem surprising that the pipes inside the room are frozen. The situation might look like this. A water pipe branch without sufficient thermal insulation runs inside unheated room and with a sharp, significant drop in temperature, it froze. This can also happen at the entrance of the pipeline to the house if the pipeline is not insulated and comes into contact with concrete or brick structures foundation or walls.

Let us immediately note that most methods for heating steel pipes cannot be used. Below we will show how to defrost water in a plastic pipe without traditional torches and a welding machine.
In our arsenal of tools there are several answers to how to defrost a plastic water pipe. But first you need to determine the place where the ice plug has formed and, preferably, its extent.

If there is no collapsible connection point or tap in the frozen area, or it is located far away, you can try to use the external impact method by pouring hot water over the pipe. In general, this method of defrosting plastic water pipes is ineffective due to the low thermal conductivity of the pipeline itself, but it can help with its small diameter and small frozen area.

The other method will also require hot water. Its essence is to supply coolant inside, directly to the place of freezing. For implementation you will need flexible pipes of small diameter, a funnel and a container for collecting thawed water. If the area to be defrosted has no bends, you can use a metal-plastic pipe. The step-by-step process of how to defrost a plastic pipe in the ground is as follows:

  • You can use a tap to enter the pipeline; if you don’t have one, disassemble the nearest connection point;
  • We place a container near it to collect water;
  • place the tube inside the frozen pipeline;
  • we move it to the place of the ice jam;
  • We supply hot water through the funnel;
  • As it thaws, the water will come out, and the pipe needs to be pushed further.

This method is more effective than the previous one, but for its successful implementation you need to have constant access to hot water.
If the water in a plastic pipe freezes, what should you do? You can try to warm it up with a self-heating cable. For any pipe diameter, spiral winding will give the desired effect over time. And taking into account the fact that this material can be purchased either in a coil or as a finished product with a fork, the labor intensity of the process is minimal.

Heating a plastic pipe for sewerage

How to defrost a plastic sewer pipe? There is an opinion that it is correct installed pipe gravity sewer, even without thermal insulation, cannot freeze due to its slope, large diameter and elevated temperature drains. And if this happens, it should be checked for blockages, damage due to soil subsidence, etc.

Fundamentally, the ways to thaw a frozen plastic sewer pipe are not much different from defrosting a water supply. Here external heating is used with the opening of the trench, electric heating pipes and subsequent installation of heat insulation. The most commonly used method is heating the liquid inside the system. Why assemble a device from a flexible metal-plastic pipe and a water heating element.

How to heat a plastic pipe using electricity

Another means of heating a plastic pipe underground is electricity. This ingenious method is at the same time simple, effective and extremely dangerous, since carelessness can cause a short circuit and receive an electric shock. When carrying out preparatory and main work, do not forget about the means personal protection and compliance with safety regulations. The material you will need is a copper two-core wire, as well as a compressor or pump to pump out the thawed liquid.

First you need to prepare the wire:

  • from a segment of 70-100 mm we remove the upper insulator;
  • one of internal wiring where the insulation is cut, we bend it and press it to the main wire;
  • completely clear the second wiring;
  • We also press it to the main wire and at the very edge, we make 2-3 tight turns on top of the first one, cut off the excess;
  • retreating from the created turns, we expose the pressed first wire and also make several turns in parallel, without touching the turns of the second wire;
  • We install an electrical plug at the other end of the wire.

In this design, it is important to ensure that the exposed wires do not move. During its operation, the wire is inserted into the pipe all the way to the frozen area and electricity is supplied, under the influence of which the ice quickly melts. As you progress, the thawed water must be removed and the wire must be pushed further.

But what if none of the proposed methods suits you? What to do with frozen water in a plastic pipe? The answer is simple. Call a team of specialists who, using an industrial steam generator, will restore the functionality of the pipeline, regardless of its purpose.

Uninsulated pipeline - sewerage, heating system or drinking water- With high degree probability may freeze in winter along with the contents, that is, speaking professional language- unfreeze. This situation - defrosting of heating pipes or other routes - often happens if the local climatic realities were not taken into account when laying the route, or the pipe laying conditions were simply grossly violated.

Causes of pipeline freezing

So, without thermal insulation of any communication pipes, they can defrost in severe frosts. This applies to both underground and surface communications with liquid. There is only one conclusion - it is necessary to insulate the routes in a timely manner. But what to do if the route is already frozen and the pipeline needs to be defrosted? Life experience gives quite a few methods for thawing pipes with your own hands, both cheap and expensive, but always effective.

  1. Firstly, some pipes may have little liquid, which creates conditions for it to freeze more quickly, for example, in an incomplete sewer;
  2. Secondly, the pipes may be incorrectly sized in diameter, and this is a direct path to water freezing;
  3. Thirdly, critically low regional temperatures may not be taken into account, and even correctly, insufficiently insulated pipes may freeze in severe frosts.

Reliable defrosting of pipelines occurs in accessible or open sections of the route - for this it is often sufficient to use a powerful flow of hot air, for example, from construction hair dryer. But thawing underground communications is a much more complex issue, and sometimes very original technologies, for example, Esmarch's mug, which will be discussed below.

The main methods for defrosting heating or water pipes consist of using common available tools and materials: a blowtorch, a stream of hot water, blowing with a construction or household hair dryer, etc. Some points need to be clarified here:

  1. It is easier to defrost steel pipes if you use welding machine: the cables are connected to the ends of the pipe, this section is heated under the influence of current for 2-4 hours;
  2. Polyethylene pipes high pressure Now they are installed everywhere, and welding is not an option for them. It is also forbidden to clear them of internal ice with a crowbar or rod, so as not to damage the walls.

Based on these restrictions, consider traditional technologies defrosting heating mains and other pipelines.

External heating of pipes

Since methods for defrosting open heating pipes, sewer systems or water supply is clear to us, we are considering external defrosting of underground routes, which is immediately complicated by the fact that the pipes will need to be excavated. The technology depends on the diameter of the pipe and the length of the frozen area - you can dig it out manually, or you may have to rent an excavator.

After digging a trench and opening the pipe, determine how the pipeline was insulated - the technology for defrosting it will depend on this: for example, polyethylene pipes can't be reheated open flame or by applying current. The temperature of the hot air stream from a hairdryer or fan heater should not be more than 100-110 0 C so that the water in the pipe does not boil and rupture it.

Steel or cast iron pipes can be heated blowtorch or gas burner, fire or other sources of open fire.

Internal heating of plastic pipe

Defrosting sewer pipes, unlike heating or plumbing, has some peculiarities. Large diameter PVC pipes allows you to warm them up from the inside, and this is a plus. But pipes can be clogged not only with frozen water, but also with debris, and this is a minus. Therefore, defrosted sewers must not only be warmed up, but also cleaned.

To defrost from the inside plastic sewer collect protozoa homemade device: connect a cable to a U-shaped heating element with a bend diameter slightly smaller than the pipe diameter and attach it to metal-plastic pipeØ ½ '' required length. Most often, the distance to the frozen area is known, so calculating the length of the cable and the length of the MP guide tube will not be difficult, even visually. After this, connect the device to the network and push it into the sewer, as shown in the figure:

It is necessary to start moving the heater from the wastewater receiver side so that the melt water can drain freely. Large diameter water pipes can be heated in the same way.

Defrosting iron pipes

It will be most effective to defrost from steel or cast iron pipes using a special industrial equipment. The principle of operation of this device is as follows: terminals through which voltage is supplied are connected to the edges of the defrosted pipe, the pipe heats up under the influence of current, and the water thaws.

As an example, the following data can be given: steel pipe length 25 m and Ø< 6 см оттает за 40-60 минут. Если диаметр трубы больше, то клеммы подсоединяют на более коротких участках, при этом нужно следить, чтобы в трубе находилась вода под некоторым давлением – это касается разморозки отопительной и plumbing systems.

Non-traditional technologies

The use of hot water implies one peculiarity in the behavior of ice: the ice plug will not let hot water into the pipe if you simply pour it from above. Therefore, hot water is supplied inside the frozen area using a hose or pipe of a smaller diameter. For example, when defrosting a straight section of a water pipe Ø 25-30 mm, it will be effective to use a piece of metal-plastic tube Ø 16 mm.

The inner tube must be straight so that it can be inserted into the water supply to the freezing depth. As soon as the tube rests on the ice, hot water can be poured into it. The flow of melt water will pour out through the gap between the pipes, simultaneously increasing the gap. The ice will melt on all sides of the plug, freeing up space for the metal-plastic tube to move further. If the frozen area has bends and turns, then instead of a tube, use a flexible but rigid hose.

A country watering hose is not suitable for defrosting - the high temperature of the water will make it soft and it will be impossible to push it further. Oxygen or gas hose, which are connected to gas or oxygen cylinders. Practice shows that such hoses can even be pushed softened over a distance of up to 15 meters. A certain difficulty will be caused by the fact that the hose remains solid.

But so far we have considered easy cases - defrosting on straight and short sections. But what should you do if the pipe froze several tens of meters from your home, and the route is still complex - with turns and bends horizontally or vertically?

Such complex problems are solved by using an Esmarch mug complete with a construction hydraulic level and a coil of rigid steel wire. You can buy all these components without any problems, their cost is low, and the effect of use is one hundred percent.

The wire and water level tube are aligned and their ends are connected on one side of the device. For greater rigidity and permeability inside the pipe, the wire is bent at the end, making a small loop. The hydraulic level tube should be 1-2 cm in front of the wire loop. The other end of the water level tube is connected to Esmarch's mug, and the tube with the wire is pushed all the way into the pipeline.

Next, you need to pour water into the water level tube - a kind of hot “enema”. Don’t forget, if you are thawing a pipe indoors, place some kind of container under it to collect the melt water. The volume of the container is easy to determine - as much hot water as you pour into the device, the same amount of cold liquid will pour out of the pipe.

As the ice melts, the tube is pushed further until the ice plug completely disappears. This technology takes a lot of time (1 linear meter per hour), but is very effective and inexpensive.

How to prevent pipes from freezing

In order not to use all of the above methods, you need to take preventive measures to prevent freezing of water pipes:

  1. Pipe laying should be carried out at a depth exceeding the level of soil freezing in the region. It is recommended to install sewerage and water supply systems at a depth of ≥ 1200-1400 mm;
  2. It is not recommended to install iron pipes sewerage, heating or water delivery in direct proximity to concrete surfaces– floors, walls, grillages and foundations, since the thermal conductivity of reinforced concrete is several times higher than the same parameter for soil, and the risk of soil freezing from reinforced concrete objects increases many times. If this cannot be avoided, then the pipes must be insulated, and it is advisable to do this with solid thermal insulation materials - extruded polystyrene foam, bulk substances;
  3. Additional protection against pipe freezing will be provided by laying a self-regulating heating cable next to the pipes;

  1. Places where pipes are laid through walls or ceilings are recommended to be insulated with soft heat insulators - polyurethane foam, mineral wool (basalt, fiberglass, stone), ecowool or other loose materials so that there is no contact between the pipes and the walls;
  2. When constructing a pipeline on your own plot of land It is recommended to take pipes Ø≥ 50 mm, since small pipes freeze faster;
  3. When choosing synthetic pipes, remember that PPU (propylene foam) pipes can crack after several cycles of freezing and thawing, and PPE (polyethylene) pipes will last as long as you need;
  4. If sewerage, heating and water supply are not used in winter, then the water from the pipes must be drained.

Since in winter the owners of private housing constructions and apartments are sometimes faced with the need to defrost water pipes, you need to remember that the faster you react and take the necessary steps to defrost a pipeline for any purpose, the smaller the section of the route that will fail. All methods are good for defrosting pipelines - both traditional and those invented out of necessity - your comfortable further living in the house depends on this.