How to install a toilet door. How to install a door in the bathroom and toilet yourself: instructions. The process of installing a bathroom door

There are two approaches to choosing a door block for the bathroom. The first of them assumes that the door is purchased for wet room, and therefore must be made of waterproof material. Adherents of the second approach believe that if the ventilation works normally and the installation of the door block is done correctly, ordinary ones can be installed in the bathroom and toilet. interior doors good quality– made of solid wood, veneered, MDF, etc. Whichever approach you choose, the selection and installation of doors in a typical bathroom should be carried out taking into account the specifics and features of the room.

How to choose suitable bathroom doors

Choosing a bathroom door is not a trivial task. When solving it, it is necessary to take into account the influence large number factors. The main ones:

• size and layout of the room;
• intensity of use of the room;
• presence and functionality of exhaust ventilation.

It is clear that if the entrance to the bathroom is located in such a way that water constantly gets on the door, the ventilation leaves much to be desired, the room itself is small, and even several people use it, then the door is made of natural wood It's better not to put it. In this situation ideal option There will be frosted glass or plastic. And vice versa: if the bathroom has sufficient area to freely accommodate a closed shower stall, corner bath with partitions, plus a powerful hood is installed in the room, then you can safely install a door made of solid wood or with veneer finishing. But even in this case wooden structure must be impregnated with an antiseptic and coated with a special waterproof varnish.

On a note! As for the color, design and decor of the door, there is design rule: if several doors open into one hall or corridor, they should all have uniform design. Only the finishing is allowed to vary.

Installation Features

So, the problem of choice is solved. It remains to solve the question of how to install a door in the bathroom with your own hands. Installing bathroom doors has a number of features:

1. Doors for the bathroom must have ventilation gap between the threshold and the door leaf. The gap is approximately 10 cm. An exception is special doors for bathrooms with a grille located at the bottom of the door leaf.
2. If the doors are made of solid wood, the entrance to the bathroom should be located as far as possible from sources of steam and water. If this requirement cannot be met, choose another option. For example, doors with laminated coating are practically not inferior in aesthetics to solid solid structures, but at the same time they are much more practical natural wood.
3. Handles and latches must be reliable, since during operation they will be subject to increased loads.
4. The width of the box should correspond to the thickness of the walls. If the walls are too thin or the box is too wide, you will have to increase the thickness of the bathroom wall, thereby reducing usable area premises, or cut off extra centimeters from the box, which is not in the best possible way will affect appearance door block.

Advice: if a kitchen or room is adjacent to the bathroom, and they are located in such a way that it is impossible to open the doors in both rooms at the same time, it is recommended to install a sliding door in the bathroom.

Self-installation

Tools and materials

You will need:

• electric drill;
• screwdriver;
• spirit level (building level);
• roulette;
• wood hacksaw;
• chisel;
• crowbar;
• polyurethane foam;
• self-tapping screws;
• anchor;
• plastic dowels;
• wooden wedges;
• gypsum plaster;
• pencil.

Preparing the doorway

Do-it-yourself installation of doors in the bathroom and toilet begins with dismantling the old door block. Dismantling is carried out in the following order:

• remove platbands;
• remove the door leaf;
• make two cross cuts on the box;
• vertical parts are broken out piece by piece old box using a chisel or crowbar;
• break out the top beam of the box.

Main stage of work

Before direct installation, check whether the frame matches the size of the doorway, and then do the following:

As you can see, installing a door to a toilet and bathroom is a labor-intensive process, but quite doable. All work is carried out using the simplest available tools.

And finally - video:

Before you install a bathroom door, there are some facts you should know. The room is constantly exposed to changes in temperature and humidity. Therefore, it is necessary to take the choice of door seriously. of this premises. It must be resistant to water vapor and at the same time retain its color, geometry and structure for as long as possible.

To install doors you will need standard fittings. It does not require special processing. But handles, latches and latches should be looked after.

The technology for installing bathroom doors must take into account the dampness of this type of room. This type of door differs from an interior door by the increased gap between it and the floor. This is required to install more ventilation for an often damp room. It also differs in the height of the threshold under the door.

Required Tools

To install the door, installation will require a number of things:

• chisel;
• drill;
• construction knife;
• level;
• hacksaw;
• roulette;
• pencil;
• screwdriver

The materials you will need are a frame, doors, anchor bolts, wooden wedges, polyurethane foam and self-tapping screws.

During repair work the opening leading to the bathroom must be waterproofed. This is necessary due to the fact that doors are often made of natural wood, veneer or MDF. They are all susceptible to humidity. And the door must be protected from it. To do this, use a diffusion waterproofing tape with self-adhesive backing. It is placed around the perimeter of the entire opening, as well as on the box. Of course, the surface should first be cleaned of dirt and dust deposits. And prime it well.

Box installation: features

An ordinary bathroom door differs from the standard one in width by about 10 cm.

Therefore, before purchasing a door, you should take careful measurements and write them down in a notebook.

It’s great if the frame and door leaf purchased in the store are the right size and ready for installation. Just screw in the screws. In this case, no adjustment is required. The door is easily installed in its place.

To make your work easier, you should assemble the frame and door structure separately. All components, including doors, are laid out on the floor. Next, the frame is assembled around the door itself. Holes are drilled for the fasteners, everything is marked, cut - in general, the box is thoroughly prepared for installation.

Otherwise, you will have to assemble the loot - the door frame and the door itself. To do this, you need to do several sequential processes.

1. Cut the box posts to a length of 2005 mm. There's a reason for this. The usual height of a bathroom door is 2000 mm. For the gaps located at the top and bottom between the canvas itself and the box, you will need to use the remaining 5 mm.
2. The next step is to trim the bottom and top of the loot. Their size includes 600 mm, 5 mm allocated for gaps, and double the thickness of the profile of the box itself. The usual door width in a standard bathroom is 600 mm, but if it is larger, then depending on the situation we use from 700 to 1000 mm.
3. The horizontal part of the box is processed. In this case, the protruding piece of the profile is removed from both ends. This is done for a reason. Remove it as much as possible. To do this, a cut is made using a jigsaw. After which the unnecessary part is chipped off. To do this, a chisel is driven from the end.

Assembling the door frame: nuances

First of all, the awnings are cut in ( door hinges). They are installed on the right or left post, depending on how the door opens. They cut in from above and below the edge at a distance of 200-250 mm. To do this, a canopy is applied, outlined with a pencil and processed with a chisel. It is easier to make a groove for awnings using a milling tool manual machine, if available.

Next, the actual collection of the box is carried out. On the floor, one long rack is connected to a short jumper. Next, 2 holes are drilled on the side of the rack. Self-tapping screws are screwed into them. They connect the 2 parts of the box. Do the same with its remaining 3 corners.

The loot is ready. It is much easier to install a door in a bathroom without installing a lower threshold.

How to install the door leaf?

Preparing the door leaf itself involves cutting in hinges, latches and installing handles. Non-mortise hinges are installed in the same way as they are installed on the door frame.

To install the latch, you will need to drill deep hole with a 25 mm diameter from the bottom at a height of 850-900 mm. For this, a drill and a feather drill are used.

After this, holes are made for the handle. They are drilled through the canvas opposite the hole in the end. It is performed using a feather drill with a 20 mm diameter. The main thing is not to damage the door when the feather comes out of the door. Best option- drill the door on both sides.

Next, the latch is installed. Before this, a groove for the decorative overlay is inserted using a chisel. The size is determined by location using a pencil. Attach the latch from the end. For this purpose, 2 small self-tapping screws, tightened with a screwdriver, are suitable.

To install the handles, you will need to insert a square and secure it with a screw. Next, the required latch hole is threaded through it, and the handle is attached to the canvas. After checking its operation, the same is done with the second handle.

Mount the box in the opening leading to the room. To do this, a rail or profile is filled. They are placed at the top and bottom of the box itself, so that they extend beyond the dimensions of the loot by 10-15 cm. The nails are driven in with future overlap with platbands. The profile will act as a stop.

You can insert a pre-measured box into the opening and wedge it with wedges made of wood or plastic. After checking the horizontal and vertical positions using a plumb line and level, the box itself is secured with dowels (bolts) inserted flush into the material itself.

The wedged box is marked with anchors at the fastening points and drilled. Holes in doorway are made in this way: they are marked through the box, which is removed, and drilled with a drill. Dowels are inserted. They mount the frame and secure it, cut in the hinges and hang the doors.

The door frame is foamed, filling the gap between it and the opening. This is done according to the instructions using a construction gun.

Sometimes the foam compresses the box and interferes with the installation of the canvas. To avoid this, install 3 or more spacers. Their size larger size blades 5 mm.

The foam dries in 6-24 hours. After this, the door is installed using awnings. You should pay attention to the gaps under and above the canvas. As is clear, installing bathroom doors is not as difficult as it seems if you act carefully and prudently.

Having decided to install bathroom doors with your own hands, House master often encounters some surprises: a bathroom is a room with high humidity, and therefore requires taking into account some features. In general, professionals say that installing a bathroom door is not much different from other similar ones. installation work. But it’s worth understanding the details to avoid mistakes.

Preparation of work: box

The installation of a bathroom door is carried out as part of general renovation work around the house. Upon completion of the renovation work, the frame in which the door to the bathroom needs to be installed will be prepared, but waterproofing is still important. It is needed to prevent moisture from spoiling door panel, and installing a bathroom door has not become a habit.

Important! How protective element Waterproofing diffusion tape works well. The presence of a self-adhesive base allows you to mount the tape around the entire perimeter of the doorway or directly on the frame. The full effect is achieved only if there is a clean and leveled surface.

Door frame installation technology: how to assemble it yourself

After the work with the opening is completed, it is worth taking on the next stage of work, which is required by installing a door to the bathroom: assembling the frame. If you bought a toilet door or an assembled bathroom door in a store, you are in luck; replacing the door in the bathroom will not take much time and will only require screwing in a certain number of screws and installing the door in place. But if all the parts arrived home disassembled, installation of the door in the bathroom will begin with assembling the frame, only then the door block and final adjustment.

Door frame installation

1. Trim long loot posts to 2005 mm. The length is determined by the standard door height dimensions (2000 mm), and an additional 5 mm is allocated for both gaps between the door frame and the hinged leaf.
2. Cut the top and bottom of the tray by 600 mm, adding the thickness of the box profile, multiplied by 2 and 5 mm, allowing for gaps. If the bathroom door has a width larger than the standard one, then the established norm of 600 mm should be changed to 700-1000 mm, respectively.
3. At the very bottom ends of the frame, remove the protruding section of the profile, which serves as a rebate for the door. Make a crosscut cut and then remove the desired part.

Important! You need to cut the profile exactly to the thickness of the slit at the widest point!

1. Installing a door in a bathroom requires good opening and complete closing, because mandatory operation is the insertion of canopies. From where the door in the bathroom opens (right-left), you need to attach the canopy at the top and bottom, keeping a distance of 20-25 cm from the edges, outline the outline and mark the groove for the canopies. If you doubt your own skills, buy loops! Thanks to the specially designed design, they do not need to be cut in and the technology for installing bathroom doors will become much simpler.
2. All that remains is to connect all the components of the door frame. Connect all the parts on the floor, this will make it easier to put the structure in place later.

The loot is completely ready. You can do without it door threshold in the bathroom, but, firstly, installation is much easier with it, and secondly, such protection against flooding of the apartment will not harm. But if you want, you can make a bathroom door without a threshold. By the way, this particular model is popular in homes where there are children and elderly people.

Preparing the door leaf

Installing bathroom doors requires preliminary preparation door leaf. This includes:

• insertion of latch, hinges,
• handle installation.

Inserting the hinges does not take much time, and in the case where there are no canopies, the hinges are already installed, so all that remains is to work on the latch. How to make a bathroom door:

1. Using a drill in the center of the end, hollow out a groove to fit the length of the latch;
2. drill a hole for the handle (it is better to arm yourself with a pen drill). It is better to drill carefully and on both sides. The alignment alignment should be determined in advance;
3. install the latch in the groove prepared in advance. The latch is secured using self-tapping screws;
4. Installation of handles is done as follows: insert a square into one handle (fixed with a small screw), thread the square into the hole for the latch and secure the handle to the canvas. Simply place the other handle on the protruding square.

All! Now you know how to restore a bathroom door if the fittings require replacement or you have finished preparing the door leaf for subsequent installation. Detailed videos The lessons posted below will help you understand how to change a bathroom door with your own hands, so you should pay attention to them. Such detailed videos will tell you not only how to install a bathroom door, but also how to replace or move the door in the bathroom.

Manufacturing details of installing a bathroom door

Once all the preparatory issues have been resolved, the question arises: how to install doors in the bathroom. All the work comes down to correct installation boxes and canvas canopy.

Important! In order not to create problems with positioning, it is better to fill the rail or profile on the side that will face the bathroom. You need to fill the profile not only from above, but also from below so that the protrusion behind the loot is approximately 12-15 cm. These strips serve as an excellent stop.

Now you can install the box in the opening, seal the cracks with foam and let it dry (it will take up to 6-10 hours). Do not forget that foam tends to expand and can compress the door block so that the leaf does not fit, so it may turn out that after installation the door to the bathroom does not close. Spacers to the size of the width of the canvas in the amount of 3 pieces must be cut in advance and installed: opposite the latch and in two spans.

Bathroom doors: final stage

When to install bathroom doors? After installing the box and completely dry foam. This is done by connecting the canopies to the box. There is nothing complicated, the main thing is to calculate exactly the gaps above and below the canvas. By following the sequence of installing the bathroom door, you can update the door in the bathroom or mount the transfer of the bathroom door.

To ensure ventilation of the room, the following rule must be observed: when it is already possible to install doors in the bathroom, it is better to provide slightly larger gaps or to cut them in ventilation grille into the canvas. The price of this additional accessory small, especially since knowing how to update and install a bathroom door yourself can save a lot of money, but ventilation will extend the life of the door itself and the lining inside the room.

It is better to carry out all stages of the process exactly, otherwise after completion you may find that the bathroom door does not close due to errors in measurements. The main thing to consider is when to install the door in the bathroom: only after assembling and installing the frame, threshold, sealing the cracks and preparing the door leaf.

The question often arises: how to install a door in the bathroom at home if it is episode 137. The fact is that standard sizes doors are not suitable for of this type buildings, therefore it is necessary to carry out some reconstruction of the openings. It is best to entrust this operation to specialists, having previously specified the cost of the door and work.

It happens that after installing the canvas everything was fine for some time, then the door to the bathroom stopped closing, what to do:

1. determine what exactly changed the size: the door itself or the frame;
2. the frame has been knocked down - remove the canvas, trim a little foam and put the door back in place;
3. the door is swollen from moisture: wait until it dries and takes its original shape, install good ventilation in the bathroom or carefully cut a piece of canvas so that the door begins to close again.

If any of the above problems occur, then after eliminating the shortcomings you need to measure the latch level. It is best to leave some power reserve, then problems with swelling of the door leaf will be solved without any special worries. Now you know how to update bathroom doors, carry out repairs, restoration, or completely replace the frame and panel, so you can carry out all the work yourself.

The equipment of a modern bathroom differs in many ways from the standard one that everyone was accustomed to in Soviet times. And interior design in rooms where it is used a large number of water, has also undergone a noticeable evolution. Doors to a bathroom, mini-pool or toilet are now selected in a single key with plumbing and other equipment. But it is not so easy to select and install a door leaf made of moisture-resistant laminate so that the doors meet all the search criteria.

Features of choosing a bathroom door

At first glance it seems that there is nothing easier to install doors to the bathroom, but this is a specific room with increased level humidity and a high probability of water penetration outside. The doorway must close sufficiently tightly at the bottom, while at the same time allowing for sufficient air recirculation and ventilation. It is these features that are important to consider when self-installation bathroom doors.

In city apartments standard layout the doorway has standard dimensions. Therefore, the size of the bathroom door, when replacing with a new one, must exactly match the previous model. Additionally, you have to change the entire door frame - in most cases, the design new door does not coincide in any way with the old design of the doorway. You can use special solvents to remove old layers from the loot. oil paint or purchase the doors along with the frame.

It is not recommended to install the first doors you come across in the bathroom, especially decorative interior ones - they can warp from excess fumes and lose their attractive appearance. Into a room with high humidity It is best to choose a door leaf made of moisture-resistant laminate or other material that is not afraid of excess moisture:

• plastic;
• glass;
• aluminum;
• composite materials.

When installing doors in a bathroom, home mini-pool or bathroom, it is important to take into account the height of the threshold, which is made a little higher than in other rooms. This is important in case someone forgets to turn off the bathroom faucet or there is a water main leak. The high threshold allows you to keep spilled water on the bathroom floor while the water supply is turned off. But the threshold should not be too high to avoid stumbling.

There must be a small gap between the door and the threshold or at the top of the door to allow air flow for sufficient ventilation. Many people know how saturated the air is with steam after taking a bath, but excess humidity is poorly tolerated by people with diseases of the lungs and cardiovascular system. It is for this reason that the bathroom is sometimes equipped with a valve. supply ventilation or leave enough clearance in the doorway when installing a bathroom door.

In a city apartment, the door block of the bathroom is much narrower than in the interior partitions, and in private houses the wall thickness can be arbitrary. Remember that when purchasing a door frame, the structure must be wider than the wall at the entrance to the bathroom or bathroom. The standard parameters of the doorway are 2.0 x 0.6 m plus the threshold. However, when purchasing, it is important to try everything on thoroughly.

Features of choosing a door leaf

To do right choice, first you need to understand what kind of doors there are and choose the most suitable ones for your home. Remember that they should look good from both sides and harmoniously fit into the design of the room adjacent to the bathroom or bathroom. Example decorative doors to the bathroom photo.

There are 2 types of doors:

• swing (swing open towards and away from you);
• sliding (moves to the side and guide).

There are also single and double doors- they are installed on a wide doorway.

A single swing door is a common type of door for a bathroom or toilet; it opens to the side using a handle. More often, budget options of this type, and they are usually installed in city apartments. The choice remains with the material, type of locking mechanism and door leaf design. The swing door to the bathroom opens, most often outward - into the corridor or hallway, where there is enough space for this. Sometimes the door opens into the bathroom, but there must be enough space there.

Also note that there are doors:

• rights;
• left.

Attention: This is especially important when the apartment or house has little space in the adjacent room. If there is another wall nearby that is perpendicular, then the doors should not interfere with each other when opening.

Sliding doors to the bathroom undoubtedly save space; they are installed where they are used swing door uncomfortable. Their installation is more complicated, the price is higher, this is due to the expensive roller mechanism and guide fixed in the floor. Most often, their installation is entrusted to specialists. When opened, such doors move along the wall.

Any interior door should fit harmoniously into the overall interior design, therefore, when choosing the interior style for the bathroom, it is important to observe reasonable balance. If the interior design style of the bathroom and the adjacent room does not radically coincide, then it is better to opt for a neutral option - with modest decor.

Attention: A door made of ordinary, not moisture-resistant materials, on the bathroom side must be coated with a special waterproof varnish or treated with a special compound that increases its resistance to moisture evaporation!

When installing a bathroom door, pre-impregnate natural wood with an antiseptic and a special antifungal compound, especially if it is made of solid wood! Special composition They also impregnate veneered interior doors, as well as chipboard and MDF doors. This is especially important if the doors for the bathroom or bathroom are made by hand or by special order.

Tip: If you want to order a handicraft bathroom door from a small private workshop, be sure to make sure that it is covered with all protective equipment. It often happens that money is paid, but the work is not completed - no impregnation or special protective treatment was not produced.

When choosing a door, also pay attention to the locking mechanism, since the built-in latch tends to close from the inside - be careful not to confuse it! If a latch handle is not provided, there must be a latch or other internal lock.

Materials for making a bathroom door

1. Plastic doors for the bathroom are very convenient and aesthetically pleasing, although they did not receive widespread for this type of premises. They are most appropriate for rooms with high air humidity. They are easier to care for - just wipe them when a layer of moisture forms. They are convenient and reliable, and are least susceptible to adverse effects. These are very light doors, so they can also be used for sliding design. They have affordable price and practical fittings - you don’t have to invent how the doors to the bathroom should close.

2. Glass bathroom doors - practical decorative option. Do not be afraid that they will break; only heavy-duty glass is used for them. Care - wipe off moisture regularly. Glass door It has additional benefit- it allows enough light to pass through, even if it is opaque. This allows you to further save electricity when using the bathroom in daytime. If you are confused that the doors can be transparent, then you can choose matte, mirror or corrugated glass: photo.

She also applies to inexpensive options, and you can even order such a door from thick frosted or sandblasted glass from the nearest glass workshop. But don't forget to purchase in advance special fittings in advance, so that the glazier draws all the holes - for the handle, locking bolts and fastenings. Finished door from decorative glass costs an order of magnitude more.

3. Laminated door with film coating or PVC - excellent performance in protecting against moisture, splashes, drops and fumes. These doors are quite common, they are environmentally friendly and hypoallergenic, and due to their popularity they make up the lion's share of the range of doors for bathrooms and bathrooms.

This door does not deform, is very convenient to use and practical to maintain. Cleaning - with a sponge with any detergent, wipe off moisture with a dry cloth. Decorative properties the doors are also undeniable; the surface copies any texture of natural wood. This is important for decorating the interior of adjacent rooms in a single design, and the prices for these doors are attractive. Budget laminated doors of economy class are presented in large assortment in all construction supermarkets and online stores.

4. Veneered doors are a coating of wood chip “halva” thin layer decorative wood valuable species. Furniture veneer is beautiful and reliable, the only thing that many manufacturers do not take into account is the practicality of such doors in rooms with high humidity. But if a layer of protective high-tech impregnation or multi-layer water-repellent varnish is provided, then the selected model will be good for adjacent rooms and practical for the bathroom.

5. Doors made of natural solid wood (wood) are high-quality, reliable, but everything mentioned about veneer is true for natural wood. Only possible with a reliable protective coating use in the bathroom. Such doors are expensive, they are not available to everyone, but they can be ordered from a carpentry workshop and all stages of impregnation can be monitored. When purchasing, it is important to read the instructions in detail or technical description to make sure it is possible to use a solid wooden door in a bathroom or bathroom.

Attention: In any hardware store Don’t be shy to ask if you don’t understand. It is better to contact consultants for obtaining and general reference information, And detailed description selected door. If the product fits perfectly in all respects for your bathroom, but is a little longer, it can be shortened by special machine and make a trim. Check to see if this store provides this service. It’s worth asking - how to install a door to a bathroom, do they have a technician come to your home, is this included in the price of the door? If you intend to install the doors yourself, make sure that you do not automatically overpay for their installation.

When installing a door, you need to consider whether it will be for the first time after completing the main stages of building a house, or whether dismantling is required old door? In this case, the process and all stages of installation will be organized differently - installation of a bathroom door video at the end of the article.

There are several options for installing a door, but remember that the bathroom definitely needs a threshold, and if you don’t have one, you should also familiarize yourself with this process in detail. It must be installed correctly and also receive sufficient sealing. Keep in mind that old doors are usually dismantled without the door frame, but if it does not match in style and it is difficult to redo anything, then you will have to remove the entire structure, along with the threshold.

Advice: It is important to eliminate wall defects before installing the door frame, and unevenness and discrepancies at the doorway can be covered with platbands or extensions.

Installing a bathroom door: step-by-step instructions

This is a responsible and time-consuming process, regardless of whether it is a door to a small bathroom or an extensive renovation of a large bathroom or home mini-pool. However, it is not recommended to experiment with this if not similar experience And carpentry tools under your hands.

When a door is purchased together with a frame, experts recommend assembling the entire structure on the floor and then installing it in the doorway. You can purchase an already assembled version when it matches your doorway size - then installation is much simpler:

• prepare the doorway;
• install finished design and wedge it, checking the level and plumb, we fasten the wedges between the wall and door block and a wall;
• secure the frame in the doorway with anchors or screws;
• fix the structure with foam on one side and place spacers in the box so as not to deform it;
• check the verticality of the structure again - this is important when closing the door;
• after 2-3 hours the first layer will set, after which the mounting foam is applied on the other side, removing the excess;
• seal the threshold on the bathroom side;
• cover the mounting foam with the outside decorative elements door frame;
• After a day, check the reliability of the installation - the box should not wobble, if this is noticeable, you need to strengthen the fastening to the wall.

Attention: When setting, the polyurethane foam increases fivefold, so it is better to apply it slowly in small portions until the space between the structure and the wall increases. Experts recommend foaming a third of the space. If foam creeps out in unwanted places, you can scrape it off with a knife and wash the surface of the finish with a sting solution.

If the door frame does not require replacement, then the purchased door remains to be tried on door frame and hang it on the hinges. They are secured to the door leaf and frame with self-tapping screws. Usually 2-3 door hinges are enough, but they need to be installed correctly by making indentations with a chisel - watch the video.

On final stage When renovating a bathroom, the question arises about installing doors. This process has some differences from the same process for installing a door in any other room.

IN in this case Moisture-resistant materials must be used, the closure must be hermetically sealed, and at the same time ensure air recirculation.

These features make installing bathroom doors a more responsible procedure.

Contents of the article:

What do you need to know before installation?

Before installing bathroom doors, you need to take into account the microclimate of this room when choosing the material from which the door is made. High humidity can deform a product made of natural wood, and then the question of premature replacement will arise.

If there is a closed shower stall and large area rooms natural materials allowed, but with a waterproof coating.

Installation is carried out after finishing the alignment of walls and other wet work so that the box does not leak from dampness. The subfloor must also be completed, when you can find out the thickness of the finishing floor in order to make the installation, taking into account the height of the threshold. If the doors themselves are being changed, then these steps can be skipped.

When choosing a door and frame, even if they have markings on them and are sold as a set, you need to personally verify the accuracy of the dimensions. This is due to the fact that the manufacturer may make inaccuracies in manufacturing, which will create great difficulties during installation. The frame beam must be smooth and free of black knots, and its thickness is the same as the door leaf.

Preparatory work

Installing bathroom doors begins with dismantling the old block, which is carried out as follows:

• They tear off the platbands;
• Remove the old door tightly;
• The box is sawn through in two places;
• The vertical segments of the old box are dismantled using a crowbar and a chisel;
• Remove the top parts of the box.

When the opening is freed from the old structure, it is cleared of the remains of the old installation material and plaster the defects, if any were made during dismantling. After this stage, and also if the door is placed in a new opening, it is necessary to prepare it. For this:

• The opening is waterproofed to prevent the influence of moisture on the door frame material;
• Dust is removed from the entire opening and a primer is applied;
• If the boxes are made of wood, diffusion tape, which has an adhesive backing, is glued along its entire perimeter. It also covers the perimeter of the opening.

Self-installation of the door

During installation work, doors will need following materials and accessories:

• Screwdriver and hand electric drill;
• Construction level, mallet, chisels;
• Construction knife and pencil;
• Miter box, hacksaw, cue ball, hammer;
• Feather drills;
• Self-tapping screws for wood;
• Small nails for casing and glazing beads;
• Polyurethane foam;
• Substrates made of wood or plastic;
• Locks and hinges.

First, the door frame is assembled and installed. If it has already been purchased finished form, all that remains is to insert it; if not, then after assembly and installation you need to make its final adjustment.

For this:

• The entire structure is assembled on the floor, after which it is installed in the opening;
• Long racks are cut to 200.5 cm when standard height opening. If the dimensions are non-standard, then the dimensions are calculated based on these dimensions;
• The top of the loot is similarly shortened to 60 cm with a standard width;
• The canopies are inserted at a distance of 25 cm from the edge;
• The box is assembled, holes for fasteners are made in advance.

The hatch can be mounted without a threshold, which makes passage more convenient. The next step will be preparing the door leaf:

• Loops are hung on it in a similar way to the same operation on a loot;
• The latch is fastened and mounted at a height of 85-90 cm from the floor;
• Drill with a diameter of 20 mm. a hole is made for the handle;
• Using a chisel, select a place for the lining from the end, having previously marked it, placing it in Right place latch. Self-tapping screws are used to secure it;
• To install the handles, use a protruding square, which is threaded into the hole, and the handles are attached to it.

The installation of doors begins with the installation of the frame. The work is performed in the following order:

• The box is inserted into the opening and fixed with special wedges;
• Using a plumb line and level, check the correct installation and make the necessary adjustments;
• The box is secured with anchors or with dowels, which must be screwed flush. Marks are placed on the doorway regarding the fastening points, the box is removed, and holes for fastening are made according to the marks;
• The frame is put in place, fastened, and the door is hung on the screwed hinges;
• The gap near the box in the opening is foamed to seal the seams. Filling occurs to a third of the volume, as the foam expands, the operation is carried out from the bottom up. Upon completion of the work, the structure is not touched until 24 hours until the foam hardens.

How to avoid mistakes?

When installing doors there is typical mistakes which are most often performed by inexperienced masters. During work, you need to pay attention to the following features in this type of work.