How to make a hook for removing a suspended ceiling. How to remove a suspended ceiling with your own hands: step-by-step instructions. Prices for a stretch ceiling kit

How to remove the side of a stretch ceiling with your own hands without damaging the frame and PVC film will be described in this article. French or PVC ceilings are quite strong and durable structures, designed to last for 15-20 years. The installation features make them insensitive to building settlement and sagging of the load-bearing slab.

But life makes its own adjustments to people’s plans. Moreover, these adjustments are not always pleasant, and, as a rule, at the wrong time. Often it may be necessary to remove the tension fabric. There can be quite a few reasons for this: the neighbors are flooded, the electrical wiring has malfunctioned, or a planned replacement of the heating system pipes is being carried out.

If the polyvinyl chloride fabric is in good condition and suits the owners, then it can be removed and, after necessary work or drying the room, install it back.

What information is needed for the job?

Before you take it off suspended ceiling, you need to have certain information about the type of fastening of the canvas and a brief knowledge of the structure of coatings.

Methods of fastening the canvas

As a rule, a warranty card is issued for tension structures made of PVC film, which, in addition to the service life, indicates the main specifications. One of these characteristics is the method of fastening the canvas in the baguette. The method of work will depend on this method. If there is no documentation for the product, then you can obtain the necessary information yourself by studying the design features.

When installing tension fabrics, the following types of fastening in the profile are used:

1. Harpoon. Quite a common type of fastener. Canvases with such edges are made to order and are the easiest to work with. A hard edge in the shape of a harpoon is welded along the edges of the film. Entering the profile, this edge unbends and holds the film in the profile.
2. Clip (cam) type. In this case, the film is fixed due to the pressure of the elastic plates plastic baguette. With this fastening option, plugs and decorative overlays are not used. Installation can be carried out without preheating.
3. Bead type. This type of fastener involves pressing the film against internal walls profile with a special longitudinal product - glazing bead.
4. Wedge type. Easy to assemble and disassemble system, accessible for independent work.

In the second and third cases, it should be taken into account that the canvas was in direct contact with the surface of the baguette and may be damaged.

Features of fastening French ceilings

The main part of French ceilings is polyvinyl chloride film. This is a durable, environmentally friendly and elastic material. One of its features is an increased response to rising air temperatures. At temperatures above +60º C, PVC film becomes soft and stretches well. As it cools, it decreases in size, becoming hard.

Therefore, for installing PVC sheets it is used special tool- heat gun. Before you remove the suspended ceiling, you should take care of purchasing it. For a one-time event, there is no point in buying it, but renting it is quite reasonable and affordable. A heat gun will be needed both for dismantling the canvas and for installing it in place.

Attention: It should be noted that polyvinyl chloride film, having incredible tensile strength, reacts very poorly to sharp objects. It is easy to pierce or cut. And this risks replacing the entire ceiling.

Method of removing the canvas

Dismantling work can, in some cases, turn out to be more difficult than the construction itself. Question: how to carefully remove the ceiling tension type independently, is relevant for many owners of such structures. It is quite possible to carry out such an operation, provided that it works quality tools, displays of patience and consistency in performing all actions.

Tools and equipment

Working with polyvinyl chloride film requires quite specific equipment, which cannot always be found in a home pantry.

So, you will need the following property:

1. Steel width 8-10 cm. Before you remove the suspended ceiling yourself, you need to round off the corners of the spatula and grind off all sharp edges. If this is not done, you can cut the film.
2. Durable pliers with long, curved jaws.
3. Construction knife.
4. A strong screwdriver with a curved end.
5. Special clothespins for securing the canvas to baguettes during installation.
6. Table, stepladder or sawhorses.
7. Heat gun. It is recommended to use a gas-powered device. Electrical apparatus has high power and can damage household electrical wiring.

When the equipment for work is prepared, you can move on to the next stage - preparing the workplace.

Preparation of the workplace

Before removing a side of the canvas or its entire surface, you need to carry out certain preparatory work.

They include:

• dismantling ceiling lamps;
• removing cages with birds, aquariums and flowers from the room;
• protection against overheating of interior items that may be damaged by high temperature(TVs, plastic windows, Digital Watch).

After the room and tools are prepared, you can begin to remove the canvas with your own hands.

Film removal process

A video about removing a French ceiling will provide significant assistance in carrying out the work. It will reveal some nuances and answer the question of whether it is possible to remove the canvas yourself.

The technology for removing the canvas directly depends on the type of installation of the canvas in the profile. Based on this, the structure is dismantled.

Important detail: Answers to the question of how to dismantle the entire surface or how to remove a side of a stretch ceiling must be considered separately, in relation to each installation method.

Harpoon mount

Cladding with this type of adhesion to the walls is easier to disassemble than others. Why? The reason is simple: this type of fixation allows for easy assembly and the possibility of repeated disassembly of the structure. Separating the canvas should begin from a part of the wall near the corner.

Removal of the canvas is carried out in the following order:

1. The decorative strip is detached along the perimeter or only on one side.
2. Using a heat gun, the room is heated to + 70º C. This is necessary so that the canvas increases in size and relieves pressure on the harpoon mount.
3. Using a dull spatula, the harpoon is pryed up and lifted.
4. The released harpoon hook is grabbed with pliers and removed from the profile.
5. Further extraction is carried out manually without much effort.

Reinstalling the canvas is carried out in the reverse order.

Cam mount

Removing the film with this fixation option is the simplest and least expensive, since in this case there is no need to warm up the room. But, great care must be taken because the spatula will come into direct contact with the film.

To detach the film, you can proceed in two ways:

1. In the corner of the room and at a distance of 50-60 cm from it, insert 2 screwdrivers between the cams. The pressure of the cams in the segment between them will weaken, which will make it possible to freely remove the film from the clamp. Repeat the operation until it is removed required quantity material.
2. Insert the spatula between the jaws and press out the movable one. The material will come out of the clamps due to the tension of the web. The rest of the material is extracted by hand.

It should be remembered that marks from the clamps may remain on the material. During installation, they can serve as a kind of guide.

Beading option

In this case, you will need a screwdriver, a spatula and a heat gun.

The sequence of work is as follows:

1. The room is warming up.
2. The decorative plug is removed.
3. In the corner, use a spatula to press out the outer wall of the baguette, and use a screwdriver to pry up and remove the glazing bead.
4. The glazing bead is grabbed by hand and pulled out of the baguette.

If there is a sufficient supply of material, it may well be inserted back.

Wedge method

The easiest way to remove film.

The sequence of actions is as follows:

1. Disconnects decorative insert, playing the role of a wedge, which causes a weakening of the pressure on the plug.
2. The plug clings to the edge with a screwdriver and is removed from the baguette.

The blade is freely removed from the groove.

Thus, it is completely doable with your own hands, subject to certain technology.

Video on the topic

The stretch ceiling can be removed with your own hands, without the help of specialists. To do this you need to know the features fastening structure(baguette) and the properties of the material from which the ceiling is made. Ceiling reupholstery and even complete installation designs do not take much time.

You will immediately understand the presence of moisture on the stretch ceiling

The owner of the apartment can dismantle old ceiling due to its deterioration (rips, drips, stains, mold formation, flooding and strong stretch marks, warping of the canvas due to deformation of the walls). Sometimes the canvas is changed to install a ceiling of a different color and texture or new electrics. Both the PVC film and the fabric can be removed from the baguette (frame) and then installed back.

Preparing the premises

The ceiling reupholstery is done in a pre-prepared room. Objects that can be damaged by high temperature are removed from the room (if a heat gun is used).

If water has accumulated on the suspended ceiling, it is enough to dismantle one part and drain it

Aquariums are removed from the room and pets are removed. You also need to remove any things that will interfere with your work. The lamp is removed from the suspended ceiling and put away in a safe place. You can remove the lamp yourself, but if the mounting is complicated, you need to contact an electrician. Removed and removed ceiling plinth or masking tape.

Tools and equipment

Before you remove and reinstall the canvas yourself, you need to purchase necessary equipment, materials and tools. To carry out the work you need:

• stepladder or strong table;
• heat gun (for heating the vinyl sheet);
• construction spatulas, from which you can make blades and hooks, or special factory blades with a curved end;
• clamps with cords to hold the removed canvas suspended (crocodiles);
• mounting tape;
• pliers with long narrow ends;
• insulating tape;
• screwdriver;
• construction knife.

Often craftsmen invent their own tools for dismantling work. So, for example, metal construction spatulas are narrowed, ground down so that they become blunt, and the corners of the working blade of the spatula are rounded.

Spatulas for suspended ceilings

Spatulas and pliers process sandpaper to remove all burrs and smooth out irregularities. The dull blade is bent to make it easier for them to reach the protrusion of the profile into which the harpoon rests. Any tool used during work must not have sharp corners or rough surfaces to avoid tearing the blade.

Before removing the suspended ceiling, you need to find out how it is fixed in the profile (this data can be found in the contract that was drawn up with the organization that installed the ceiling). There are three types of fastening of the canvas in the profile: harpoon, wedge (bead) and clip.

How to remove a suspended ceiling with a harpoon mount

A harpoon is a plastic flexible strip, which in cross-section is a hook (or harpoon, which is where the name comes from). The plank has medium hardness and is produced by the meter.

The polyvinyl chloride fabric is marked and cut out, exactly copying the shape of the ceiling. A harpoon is welded to the edge of the canvas, along its entire perimeter. This is done using HDTV equipment, which is available at enterprises that install suspended ceilings. Once the harpoon is welded around the perimeter, it is firmly butt welded. The harpoon is inserted with a spatula into the groove of the baguette (profile), where it is fixed on the inner protrusion of the profile using its hook.

If the film is edged with a harpoon, removing the suspended ceiling with your own hands will not be difficult. To vinyl ceiling has become more flexible and stretchable, it is evenly heated with a heat gun. Recommended temperature heat flow- 70 degrees Celsius. Re-upholstering the ceiling starts from the corner of the room. Some home craftsmen heat only the corner from which the harpoon begins to be removed, and use a hairdryer to heat the vinyl.

Harpoon fastening of suspended ceilings

When removing PVC sheets it is necessary to remove the harpoon from the ledge (shelf) inside the profile. If this can be done in one place, then the rest of the canvas is removed by simply pulling it with a harpoon. The operating procedure will be as follows:

1. Heat evenly suspended ceiling, starting from its central part to the corners.
2. Take a bent spatula and a screwdriver.
3. Find a place in the corner areas of the ceiling where there is a sufficiently large gap between the wall and the surface of the canvas. It is necessary to ensure that in the removal area there is no place where the harpoon is glued end-to-end. This place is not very strong; the film may rupture under physical impact.
4. Using a screwdriver, press out the harpoon, insert a curved spatula into the crack and hook the harpoon.
5. To release the harpoon, move the spatula to the right and left by 10-15 cm, thereby slightly pushing the harpoon away from the baguette.
6. The same thing is done on the other, perpendicular wall. This way, the harpoon in the corner of the room will be hooked by 2 blades.
7. The shoulder blades are parallel to the wall and pulled down with little effort. The canvas with the harpoon comes out of the profile.
8. Then move the blades along the walls and carefully pull out the film. If the ceiling area is large, the canvas is hung on clamps (crocodiles) to avoid stretching and deformation.

If the ceiling area is small, the vinyl film can be removed without preheating, for canvases big size Preheating is required.

Dismantling a ceiling with glazing bead (wedge) fastening

Is it possible to remove a suspended ceiling with glazing beads? It is possible, but you need to keep in mind the fact that it will be difficult to put it back, since after installation the builders leave very little stock of canvas, but if there is a supply, it is possible.

Glazing bead (wedge) - special plastic profile different sections. The bead is inserted inside the profile, pressing the material tightly. This type of fastening is used when installing both vinyl and fabric ceiling structures.

In order to remove PVC film or fabric, you need to remove the glazing beads from the profile by hooking them with some kind of curved tool (curved spatula, spatula, hook). Dismantling begins in the corner of the room.

• Before dismantling, the polyvinyl chloride film is heated with a heat gun. There is no need to warm up the fabric.
• The profile is slightly expanded using any handy tool(for example, a thick screwdriver, long-nose pliers).
• A curved spatula (or two) or a hook is carefully placed behind the glazing bead and pulled down. The glazing bead comes out and the canvas is released. This must be done very carefully, since the edge of the vinyl film or fabric is not protected by anything and is easily damaged.
• At large area From the ceiling, the freed canvas is hung on clamps with cords.

Removing a ceiling with a clip fastening

Only low-stretch fabrics with polymer impregnation are mounted in clip fasteners. Clip fasteners are a special plastic profile, which in cross-section is a clamp.

Cam fastening of a stretch ceiling (clip)

The fabric is simply tucked inside the clip with a spatula, and the clip holds the fabric and prevents it from coming out.

• Seamless dismantling fabric ceiling start from the middle of the wall, not from the corner.
• To remove the canvas from the clip profile, you need to apply moderate pressure on the canvas in the place adjacent to the wall. In this case, you can slightly release the fastening with a screwdriver or thin pliers.
• The tension of the fabric will loosen and it can be carefully pulled out of the fastening.
• If the fabric was cut very short when installing the ceiling, then during subsequent installation it will be difficult to tuck it into the mount.

Stretch ceilings are beautiful, fashionable and unusual. All more people give preference this species finishing. Of course, this is facilitated by many reasons why the choice falls in favor of suspended ceilings - practicality, durability, impeccable appearance and perfect Smooth surface. In addition, unsightly communications and wires can be hidden behind the canvas.

Events in our lives sometimes develop in such a way that it is necessary to immediately remove the canvas. These situations cannot be predicted. If such a need arises, then you need to take action as quickly as possible. Many resort to calling craftsmen from the company that made suspended ceilings. Naturally, this service is provided for a fee. There is nothing difficult in dismantling a stretch ceiling with your own hands; the main thing is to follow the recommendations and be extremely careful.

In addition to the fact that there is PVC film or fabric base, there are still some nuances that need to be taken into account. Not all types of suspended ceilings can be removed from reverse installation. You need to know this when dismantling, so as not to be upset later. If you completely replace it with a new one due to a boring design or color, you don’t have to think about it, since they will install a completely different canvas.

When dismantling a suspended ceiling in an apartment, familiarize yourself with the type and type of structure installed (this data is indicated in the contract from the company). This knowledge will allow you to avoid mistakes and perform the removal yourself without the help of specialists.

Stretch ceilings are divided into types:

• Made from PVC film;
• On a fabric basis.

Installation of a stretch ceiling from polyvinyl chloride film occurs due to exposure to high temperature. Using a heat gun, the room is heated to 700 degrees. When installing a fabric-based ceiling, there is no need for heating. This is a significant advantage of this type of canvas.

As for dismantling, they are characterized by the following technologies:

• Removing PVC film from the structure begins from an angle (arbitrary);
• The fabric base is dismantled from the center.

Of course, a mention in a nutshell does not give a complete picture of the technology for removing a stretch ceiling with your own hands. Success directly depends on the accuracy of actions and slowness in the process. Read on for more information on how to dismantle both types. But first we should mention the necessary tool for independent work for removing suspended ceilings. It also differs, depending on the type of canvas.

DIY tools for removing suspended ceilings

In order to begin any work, you should carefully study the technology and prepare the necessary equipment. 99% of the success of removing a stretch ceiling with your own hands depends on accuracy and leisurely actions. The saying “if you rush, you make people laugh” is very suitable for this situation.

As for the tools, their choice depends on the type of stretch ceiling, but in general you will need:

1. Small plaster spatula;
2. Long-nose pliers (pliers with long jaws);
3. Stepladder (if it is missing, replace it with a table, stable chair, stool);
4. Electrician's knife (fitter);
5. Gloves;
6. Screwdriver with curved end;
7. Construction clothespins large sizes(clamps).

In order to dismantle a suspended ceiling made of polyvinyl chloride film, you will additionally need a heat gun. Since the installation process occurs under the influence of high temperatures, removal must be carried out using the same technology.

Grind off the corners of the plaster spatula and wrap the entire sharp surface with reinforced tape. If this advice is ignored, there is a risk of damage to the canvas.

How to disassemble a suspended ceiling with your own hands

Before you start withdrawing, it is important to know about correct sequence actions and initial preparation of the premises. Everyone is removed from the room plastic items furniture and accessories. It is also better to remove fresh flowers from the premises during both installation and dismantling. The windows are covered with fabric.

You need to start the removal process by warming up the room, and further actions depend on the type of construction (this point can be clarified in the contract):

1. Harpoon mount. Its essence lies in the hook, thanks to which the canvas is securely attached to the profile. Dismantling is carried out from one corner: the harpoon is grabbed with long-nose pliers and carefully bent. You should be very careful and pull out part of the fabric by the hook. If you pull the PVC film or fabric base, damage is guaranteed. After removing one edge, further removal is done manually (using gloves).
2. Bead fastening. This is a small element with which the canvas is fixed in the baguette. To remove it, you must also start from one corner. Using a screwdriver with a curved end, remove the glazing bead along with the blade.
3. Wedge mount. To remove it by hand, bend the profile and remove the blade along with the lock. The easiest way to disassemble, but only if the installation technology was fully followed by the craftsmen (they should leave a small allowance for convenient disposal of the canvas in the future). If they did not take this point into account, the process could drag on for a long time.

The technology for dismantling a fabric-based stretch ceiling is no different from PVC film. You just don't need to heat the room. Removal occurs from the center of the ceiling, and not from the corners. For quick and high-quality execution It is best to call someone for help. If you do it exclusively on your own, it will take a lot of time.

Partial dismantling is carried out using the same technologies (heating). Its necessity arises in the case of draining water from PVC film, since the fabric base does not retain water.

In all cases, the main thing is to treat the canvas with care. Although it is durable, it is not subject to mechanical stress. And we must not forget about accuracy and concentration.

Removal of a stretch ceiling with subsequent installation

There are times when it is necessary to remove the canvas to carry out some manipulations: get to communications, replace wiring, drain water by bending one corner (if the neighbors above are flooded). But, in order not to resort to installing a new stretch ceiling, be patient and remove it without damage. If its structure remains unchanged, then such a canvas can be reused.

Fasteners affect the removal process. The main thing is not to damage the canvas, so that it can be put back in the future. Familiarize yourself with the type of fastening and perform the work as carefully as possible while wearing gloves. Prepare all tools in advance: wrap them with reinforced tape and sharpen the burrs.

An inevitable option for dismantling are disposable profiles. In this case, the canvas is simply cut to be removed from them, without the possibility of reinstallation.

Instructions: how to remove a suspended ceiling with your own hands (video)

Removing a suspended ceiling with your own hands is not difficult, but actions must be careful and careful, otherwise there is a risk of damage to the canvas and additional costs. new installation. When carrying out work, do not give in to emotions, and then the result will meet all your expectations.

Hanging ceiling system, like any other, may need repairs, for which it has to be partially or completely dismantled. You can invite craftsmen or try to do everything yourself. Let's figure out how to remove it yourself so as not to spoil the panel.

1. Determine the type of tension systems

Before you start work, you need to decide what you have to deal with. The principle of fastening directly depends on the material from which the canvas is made. This can be one of two varieties:

• Textile. Made from synthetic fibers, soaked special compounds. It is characterized by high strength, wear resistance, and is not sensitive to low and high temperatures. Completely safe, fire resistant, and retains sound well. Among the disadvantages, it is worth noting low ductility, significant weight and higher cost compared to its analogue.
• Film. It is made of polyvinyl chloride and can have different thicknesses. Sensitive to increases and decreases in temperature. It stretches when heated, and cracks when frozen. It is safe provided that it is a high quality product.

Methods of fastening structures

Regardless of the method of fixation, installation suspension system starts with installing profiles. It is they who will subsequently hold the tension panel. Three methods are used to fix it:

• Harpoon. A special edge is welded along the edges of the canvas; its shape resembles a harpoon. The film is tucked into the profile, where the edge spreads out and holds the ceiling in place.
• Bead or wedge. The edges of the canvas are fixed in the profile with a special spacer element called a bead.
• Cam, also known as clip-on. The material is held by specially shaped elastic plates located inside the baguette.

2. We carry out preparatory work

Before you shoot, start with preparation. First of all, you need to choose a stepladder. It should be stable and high enough to make removing the canvas comfortable. In addition to this, you will need the following tools:

• Spatula for . Its main difference from conventional construction is the absence of pointed corners. If this is not the case, you can make it yourself. To do this, take a regular tool 9-10 cm wide, grind off the sharp edges on it and round the corners.
• Mounting clothespins. They are used to temporarily secure material to baguettes.
• A strong screwdriver, its end should be bent.
• Pliers with curved long jaws.
• In addition, when dismantling the PVC coating, you will also need a heat gun. With its help, the film is heated so that it becomes plastic.

After all the tools are prepared, you need to prepare workplace.

1. We temporarily remove from the room all items that may deteriorate under the influence of high temperature, remove plants, etc.
2. If possible, we protect from overheating that part of the environment that cannot be removed.
3. We dismantle everything

3. Determine how to remove a suspended ceiling with your own hands

The technology of the dismantling process depends on the method chosen for installation. Let's look at each of them in detail.

Harpoon fastening

Used only for PVC coating. The fastener is very convenient because it allows you to disassemble the structure many times without damaging the panel. They start removing the film from the corner. Actions are carried out in the following sequence:

1. If the joint is closed decorative elements, we remove them.
2. Turn on heat gun and raise the temperature in the room. This is necessary for the film to heat up and stretch. The tension will decrease and the mount can be disassembled. We heat the film from the center to the corners.
3. Use a screwdriver to press out the harpoon. Carefully insert the spatula into the gap and lift the harpoon. We move the tool left and right, thereby pressing the fastener away from the baguette. We do the same on the opposite wall.
4. Pull the spatula down, releasing the panel from the retainer. Moving the tool along the profile, we continue to remove the film.

If the covering is subsequently intended to be pulled back, it must not be deformed.

Fixation with glazing bead

Used for all types of ceilings. For dismantling, it is necessary to remove the fastening elements-beads from the profile. We offer step-by-step instructions.

1. Heat the polyvinyl chloride until it softens. If the ceiling is fabric, this is not necessary.
2. We take long-nose pliers or a bent screwdriver and very carefully open the profile.
3. Place the spatula behind the bead and pull it down. The fastener comes out of the groove and releases the panel.

As in the previous case, we secure it with clamps so as not to deform it.

If the glazing bead fastening is dismantled, it will be possible to put the tension panel in place only if the installers have left a sufficient supply of material. Otherwise, it is not possible to stretch the fabric.

Clip fastening

Designed for installation of low-tensile coatings, such as polymer-impregnated fabrics. A clip is a type of fastening into which the edge of the covering is tucked inside. To remove it yourself, you need to remove the edge from the lock. We begin dismantling from the middle of the wall.

At the junction of the ceiling and wall surfaces, press the panel. At the same time, carefully loosen the fastening with pliers or a screwdriver. The fixation of the fabric loosens and it can be removed from the clip. We do everything carefully to preserve the canvas. You will need it for subsequent installation. True, this is only possible if the fabric was not cut too short during installation.

Features of dismantling the fabric structure

Many people are concerned about maintaining the integrity of the fabric during dismantling, since it is not elastic enough. Fears are in vain if the work is done correctly. There are several rules to consider:

• Remove the fabric covering only from the middle to the corner. Subsequent installation, if provided, is carried out in the same way.
• Warming up the room during operation is necessary, but it should not be as strong as for PVC film.
• Small irregularities can be removed yourself by heating problem area. It is important to know that the heat source should not be brought close to the coating. Otherwise it will become deformed.
• It is impossible to partially remove the fabric panel, as is possible for a film panel. The fasteners will not withstand the weight of the material, which will lead to the breaking of the fasteners.

To eliminate any remaining questions, we suggest watching a video on the topic.

As you can see, if such a need arises, you can remove it and put it back. We told you how to do it right. This is a rather complex procedure that must be performed with strict adherence to technology. It is unlikely that you will be able to cope alone. It is advisable to find assistants who will ensure safety and high quality works

Information on how to remove a suspended ceiling yourself can be useful in several situations. For example, in case of damage to the canvas. This is also relevant when repairing wiring, or its first installation, when it is necessary to completely remove the structure. May also be necessary partial dismantling in case of flooding, to drain the water. If you do not want to turn to professionals for help, then with the help of our recommendations you will know how to properly remove a suspended ceiling with your own hands.

The main thing in work is to be careful, because our first goal is to preserve the integrity of the canvas. It is also important that the specialists installing the ceiling do not make it flush to size, but leave a little material so that you do not have difficulties when re-stretching it, and all the holes for spotlights and chandeliers. This idea will not take much time, since it is quite possible to remove the suspended ceiling yourself. First you need to decide what material you have and on what mounts it was installed.

Features of dismantling

Materials for dismantling are divided into two types:

• PVC: requires heat treatment during dismantling.
• seamless fabric: do not require heating, and the removal process starts from the center to the corners.

Also, before dismantling, you need to familiarize yourself with the types of profiles and determine which one you installed. Profiles, or baguettes, are used when installing suspended ceilings as support for fabric or film material. The moldings are fastened to the wall. They are divided into two types.

1. The first ones are made in such a way that it is possible to remove them without much difficulty. ceiling structure, and then put it back in the same form.
2. The second type was called “disposable” by the experts themselves, since with such a profile it is impossible to replace the tension fabric without damage.

When ordering a new sheet for the first time, consult with the installers about which profile will be used during installation. Perhaps they will offer you a choice. The best decision – aluminum profile, with which you can easily dismantle it at home. It's better to overpay once quality material than to spend money on a new ceiling again.

In addition, there are different types fastenings. It is important that the fastenings on fabric tension systems are different from those installed on vinyl. There are universal ones that are used for both types. In this case, the connection to the profile is created thanks to glazing beads, which are quite difficult to remove in case of flooding - more patience and care will be required so as not to damage either the canvas or the glazing beads. It will be difficult to do without relevant experience, so this fastening method can be called one-time, but at the same time the most popular due to its low cost.

There are systems that facilitate the process of removing and re-tensioning the fabric, and there are different systems for each type. For PVC, the harpoon method is used, for fabric - plastic clips. It is important that when fastening with clips, you cannot remove part of the canvas, only the entire ceiling.

The process of removing a PVC stretch ceiling step by step

After our article, it will be useful to watch the video on the YouTube channel to better understand how to carefully remove a suspended ceiling. This process is similar to installing the structure, only you need to do it in reverse order. First you need to remove everything in the room, especially sharp objects, cornices, and remove all light bulbs, shades, floor lamps and others lighting so as not to damage the canvas.

First, you should remove the rubberized insert between the ceiling and the wall yourself. This is a simple event in which the main task is to find the junction of two connected parts. It is securely hidden if the installation was carried out experienced specialists. The easiest way to find it is in straightforward tensile structures, since here the joints are usually located in the corners of the room. But if you installed a complex designer model with numerous decorative elements, then you will need to put in a little more effort.

The next step will be to heat the room as a whole and the canvas separately using a gas gun. If you ignore this action, it threatens to damage the stretch ceiling and make it unsuitable for use. further exploitation. Carry out the work in parts, starting from the place you are going to dismantle in this moment. Warm up this area thoroughly.

The video at the end of the article will show how to properly remove a suspended ceiling: in the case of a standard rectangular canvas, start dismantling from the corner. With curved ones (for example, an oval), you don’t have to limit yourself in choice and start with any convenient place. The best option one where you can carefully hook the edge of the film (or textile material). To identify it, you will need a stepladder and a little care. Carefully examine the perimeter, looking for protruding edges that will be easy for you to grab with long-jawed pliers. If there is no such place, then try starting from a corner or something similar, depending on the choice of design.

Life hack! To avoid damage stretch fabric using pliers, you can sharpen the outer corners of the tool (it is better to use old instrument). Achieve perfect smoothness with rounded and polished edges, and you don't have to worry about possible punctures.

Next comes the jewelry work - you need to remove the hanging material from the profile so carefully that not a single scratch remains on it, regardless of whether it is PVC or fabric. This should be done carefully, without unnecessary movements, and only in places where the canvas is well heated. Since it is not always possible to remove a suspended ceiling using a video yourself, it is better to carefully familiarize yourself with the dismantling conditions and unquestioningly follow all the instructions. It wouldn’t hurt to get an assistant who will move gas gun as you move towards the edge. Or you will have to do it yourself, which is not very convenient.

The method of dismantling will also depend on the fasteners.

1. In the harpoon system, it is correct to grab the harpoon with pliers, and not the canvas, which can be damaged. After partially freeing the ceiling, you can continue working with your hands rather than with tools. Use special gloves to avoid leaving marks on the heated material.
2. In a glazing bead (or wedge) system, the start of work is similar to that described above. To do this, you may need a narrow spatula with pre-ground sharp corners. Additionally, it can be treated with reinforced tape. Use a spatula to bend the profile slightly to release the glazing bead. Next, use a sharp-tipped screwdriver to completely pull it out. If there is no spatula, then the wedge can be removed using your hands.

For fabric, the process is the same only without preheating. To correctly put the fabric back on, follow the sequence of actions, then you will not have any difficulties on how to tighten a removed stretch ceiling. The main thing is that during dismantling all materials, including fasteners, remain intact.

Now you know how to remove and put on a suspended ceiling yourself. The main thing is not to be afraid to test your knowledge in practice. If you don't want to take risks expensive material, seek help from professionals who will do everything quickly and at a reasonable price.