GC TechnoSpetsSnab: sale of industrial and construction equipment. GC TechnoSpetsSnab: sale of industrial and construction equipment Design, principle of operation

The MAKAR TV5 fan heater is designed to create and maintain a constant thermal regime, heating in workshops, garages, shops, construction sites, warehouses and other premises. The fan heater can also be used as an addition to traditional heating systems, for example, for a store, workshop, warehouse, and for technological purposes (drying surfaces after painting or plastering).

• Power 3.0 / 5.0 kW
• Voltage 220 V
• Installation - floor
• Dimensions 280x340x315 mm
• Weight 7.5 kg
• Temperature difference C° 35

Contents: fan heater, instruction manual, packaging. (Power cable and plug are not included)

Cable cross-section for connection - 3x2.5 mm (copper cable)

MAKAR devices are fully automatic. When the room temperature reaches the value set by the thermostat, the heating elements automatically turn off. At the same time, the engine continues to run. As soon as the room temperature drops, the heating elements automatically turn on.

Distinctive features of the MAKAR fan heater:

• The highest air temperature at the outlet of the heat gun is due to the patented composition of the insulator of the heating elements.
• Heating elements made of stainless steel are used as heating elements. The minimum service life of heating elements is 25 thousand hours. This is about three years of continuous work.
• All heat guns are equipped with electric motors, the minimum service life of which is 28 thousand hours. This is more than three years of continuous work. (1 year - 8760 hours)
• In hot areas, the wiring is made of high-temperature wire with special fire-resistant fluoroplastic insulation (does not burn, does not smoke). Similar insulation is used in the aviation industry
• The body is painted by powder coating with a high degree of adhesion in a painting chamber at a temperature of 220 degrees C, which ensures a long service life of the painted surface (at least 10 years)
• The air temperature in the room is controlled by a thermostat.
• Protection against overheating is carried out using a temperature sensor, which turns off the heating element when the case overheats, and turns on the heating element when the case has cooled down.
• Short circuit and phase imbalance protection
• Structural protection of electrical switching units and the electrical system of the heat fan from mechanical damage and moisture on the power units (! Which is very important when used on construction sites, etc.).
• Heat guns and fan heaters "MAKAR" are fully automatic. When the room temperature reaches the value set by the thermostat, the heating elements automatically turn off. At the same time, the engine continues to run. As soon as the room temperature drops, the heating elements automatically turn on. Thus, heat guns (fan heaters) "MAKAR" are fully automatic. Many analogues of heat guns and fan heaters of other brands do not have such an automation system, therefore, after the heating elements overheat, they have a COMPLETE shutdown of the heating elements and the engine. On equipment from OTHER MANUFACTURERS, to resume operation, you must press the “reset” button, which returns the automation system to its “original” position.

Distinctive Features heat gun (fan heater) "MAKAR" are fast heating of the air in a heated room, stepwise power control, protection against overheating using a thermostat.

You can buy a 5 kW 220V fan heater - MAKAR TV-5 electric floor-standing

Contact us

Do you have a question, haven’t found the equipment you need, or something else?

If equipment selection is required, indicate the maximum possible amount of available data, preferences, restrictions, or vice versa possible changes

and/or fill out the questionnaire

Power, kW: 3.0/4.5
Power, V: 220
Dimensions, mm: 300*420*360
Weight: 7.5
Article: MAKAR TV-5/220M

Fan heater "Makar TV-5" 220 V

To choose the right fan heater needed for heating, you need to know its structure and operating principle.

The function of the Makar TV-5 fan heater is to create and maintain a constant temperature regime at construction sites, workshops, warehouses, garages and other premises, as well as in addition to heating systems and for drying the surface after painting or whitewashing walls.

All fan heaters are equipped with electric motors that can operate continuously for about three years. Heating elements made of stainless steel, the service life of which is at least 25 thousand hours, are used as heating elements. The wiring is protected by special fire-resistant fluoroplastic insulation and is made of high-temperature wire. There is short circuit protection. The air temperature is regulated using a thermostat, and the TV 5 fan heater is protected from overheating by a temperature sensor, which turns off the heating element if the housing heats up and turns it on when the temperature drops. Thus, “Makar TV 5” is a fully automatic fan heater.

The switching units and electrical systems of the device are protected from mechanical damage and moisture. Light in weight, only 6.5 kg, these fan heaters are quite productive - 535 cubic meters. m/h. Fan heater TV 5 has a power of 5 kW and an outlet temperature of up to 90 °C. It can heat up to 50 square meters of area with an air flow length of 1.2 m. Therefore, if it is necessary to heat larger areas, you can use several devices of equal power.

– a heating device for use as a main or additional heat source in various industrial premises.

Price: 3500 rubles

Application form Description

Used in construction for drying painted and plastered surfaces, for warming up engines in moderately cold climate zones.

The unit is not suitable for use in domestic or home conditions not related to business activities.

Do not expose the device to atmospheric influences. The permissible humidity level is 80% (at ambient temperature + 15°C).

Technical specifications

Characterized by the following basic technical data:

• Air capacity: 535 m³/hour;
• Power supply voltage: 380/220V;
• Power consumption: 5 kW;
• Outlet temperature: +90°C;
• Product dimensions: 165×350×400 mm;
• Weight: 6.2/6.2 kg.

The design provides for continuous operation. Power supply – from a single-phase or 3-phase power supply.

The Makar TV-5 fan heater is equipped with a temperature relay for smooth regulation of the microclimate in the room, and has a protective sensor with automatic return.

During operation, no electromagnetic, electrostatic fields or ionizing radiation arise. The unit has protection against electric shock in accordance with GOST 12.2.007.0-75 (class 01).

Contents of delivery

Supplied in a packaging box, complete with support legs (2 pcs.), instruction manual, socket and self-tapping screws 4.2x25 (4 pcs.).

Device, principle of operation

Structurally, it consists of a metal case on a support stand, equipped with a handle for carrying. Inside the case there is electric motor, axial fan and heating elements.

In the front part of the panel there are switches and a control thermostat.

Restrictions on use:

Forbidden:

• Allow water to get inside;
• Block the outlet or inlet;
• Touch the internal parts of a device connected to the network;
• Use the heater without grounding;
• Use the appliance with a damaged plug or cord;
• Leave flammable mixtures near a running fan heater;
• Direct the operating unit with its outlet towards a wall located less than 1 meter away;
• Use the product with the control panel removed and the protective walls removed.

During prolonged inactivity, the power cable plug is disconnected from the socket.

Preparing for work

The procedure for preparing for operation is as follows:

1) Remove the product from the packaging;

2) Assemble according to the diagram, secure the stand legs with screws;

3) Provide access to the switches, ensure free air intake with appropriate openings;

4) Set the switches to the “Off” and “Fan” positions;

5) Connect the mating part of the connector to the switchboard through a circuit breaker.

Exploitation

When the switch is turned to the “On” position, it starts in fan mode. After setting the “Heat” mode, the unit begins to operate at full rated power.

Shutdown is performed in the following sequence:

• The “Fan” mode is set;
• A time of 3-5 minutes is maintained to cool the heating elements;
• The unit is turned off by moving the switch to the “Off” position;
• The power cord plug is disconnected from the outlet.

Power adjustment

The thermostat ensures that the rooms are heated to the desired level. It works on the principle of turning on/off heating parts depending on the current temperature. By rotating the control thermostat handle clockwise, the set temperature is increased, and in the opposite direction, it is decreased.

To work with Makar TV-5 fan heaters, technical personnel must be instructed and familiarize themselves with the operating manual.

A compact, high-performance heating device capable of warming up a room of up to 50 square meters in a short time. m!

The only fan heaters on the domestic market with a three-year warranty!

Description: MakaR automatic fan heaters are full-fledged heating devices that can both complement traditional heating systems and independently heat the room.

Distinctive features of MakaR fan heaters are rapid heating of the air in a heated room, stepwise power control, and protection against overheating using a thermostat. MakaR fan heaters are fully automatic. When the room temperature reaches the value set by the thermostat, the heating elements automatically turn off. At the same time, the engine continues to run. As soon as the room temperature drops, the heating elements automatically turn on. Many analogues of heat guns and fan heaters of other brands do not have such an automation system, therefore, after the heating elements overheat, they have a COMPLETE shutdown of the heating elements and the engine. On equipment from OTHER MANUFACTURERS, to resume operation, you must press the “reset” button, which returns the automation system to its “original” position.

The highest air temperature at the outlet of the heat gun is due to the patented composition of the insulator of the heating elements. Heating elements made of stainless steel are used as heating elements. The minimum service life of heating elements is 25 thousand hours. This is about three years of continuous work. In hot areas, the wiring is made of high-temperature wire with special fire-resistant fluoroplastic insulation (does not burn, does not smoke). Similar insulation is used in the aviation industry. The body is painted using powder coating with a high degree of adhesion in a painting chamber at a temperature of 220 degrees C, which ensures a long service life of the painted surface (at least 10 years)

Manufacturer: The Makar brand was founded in 1999. This brand is the first brand of industrial equipment in Russia to unite several manufacturers. Currently, the MAKAR trademark is one of the most famous and dynamically developing. MakaR brings together only the best, proven examples of industrial equipment. All manufacturers included in the Makar program set themselves the goal that the equipment produced under this brand is of increased quality and reliability.

Warranty and post-warranty service for MakaR products is supported by service centers located in Moscow, St. Petersburg, Samara, Yekaterinburg, Ufa, and Krasnodar.

Options:

Power, kW - 5
Voltage, V - 220
T-ra at the exit, C - 90
Flow length, m - 1.2
Production, m3/h - 535
Lv. noise, dB 34
Dimensions, mm - 165/350/400
Weight, kg - 6.5

General information

Fan heaters "MAKAR" are used as the main or additional source of heat and are intended to create and maintain a constant thermal regime in residential, office, retail, warehouse and industrial premises, as well as on construction sites, workshops, garages, etc. In addition, the equipment is used in construction and in technological processes - for drying surfaces after painting or plastering.

Distinctive features of MAKAR fan heaters are rapid heating of the air in the heated room, protection against overheating using a thermostat. Effective efficiency - no less than 98%.

When the temperature in the room reaches the value set by the thermostat, or the temperature of the heating elements approaches critical, the heating elements automatically turn off. At the same time, the engine continues to run. As soon as the temperature in the room decreases, or the automation detects that the heating elements have cooled down, the heating elements are automatically turned on. Thus, fan heaters "MAKAR" are fully automatic and can work without human intervention.

Many analogues of fan heaters of other brands do not have such an automation system as the MAKAR equipment, therefore, after the heating elements overheat, they have a COMPLETE shutdown of the heating elements and the engine. On such equipment, to resume operation, you must press the “reset” button, which returns the automation system to its “original” position.

Take this circumstance into account when choosing a fan heater!

The main advantages of fan heaters and heat guns "MAKAR".

• outlet temperature up to 95C°;
• high air performance;
• high speed of heating of rooms;
• noise level 32 dBa;
• effective heat flow range 1 meter;
• fully automatic;
• air flow direction adjustment;
• fully equipped and ready to work;
• dust- and moisture-proof design;
• fireproof;
• protection against overheating, short circuit and phase imbalance;
• guarantee - THREE of the year.

Specifications