A house for children on a summer cottage. How and from what to build a children's playhouse in the country. House on poles for children

There is a considerable selection of options for children's houses on the Internet for your beloved baby, both with a large budget and with a small one, but the budget does not play the most important role in this matter. Your imagination is also important here!

We propose to consider three options for children's houses: budget, moderate and outstanding.

Children's playhouse - budget, portable

This option is well suited for low-budget families, since it requires: little time for construction, not a large number of simple tools and not large investments.

In order to save money, instead of buying a board, we will use ordinary pallets for dry mixtures, they have a fairly strong and thick board of 22 mm, moisture resistance up to 27%, ready-made dimensions, and also in the inside of the pallet there are squares on which it will be stand the future fortress of your baby.

Material to be used

1. Board 100 mm wide, 22 mm thick, 1,200 mm long;
2. Beam 50x50; FSF plywood: Long - 2.44 m; Width -1.22 m; Thickness - 6.5 mm.
3. Screws 3.5x45 with large pitch for wood;
4. Iron fastening corners for wood;
5. 4 cinder blocks or 16 bricks.
6. If you decide to use brick, you will need: 5 kg of Ceresit CM 11 mixture. Cement and sand are also suitable.
7. Corners;
8. Door hinges and two handles.

Don’t forget that children also need a little freedom, to be alone, to have their own little secrets from adults and to develop their creative thinking in their beloved and beautiful little house.

Tool

• Hammer;
• A crowbar or pry bar;
• Roulette;
• Square 30 cm;
• Pencil;
• Shovel;
• Levels: 1 and 2 meters;
• Drill with cue ball PH–2;
• Hacksaw, Circular saw, jigsaw;
• Thread or fishing line; (lacing)

Preparation for construction

First of all, we choose a small site with an area of ​​3x3 or 4x4. The site must be clean of stones, glass and other debris!

1. Pallets must be intact, not doused with toxic chemicals, and not painted.
2. Disassemble, do not break!

Carefully remove the nails, use a crowbar and pry the board up with a pry bar. If the pallets are dirty, they should be cleaned, you can simply spray them with water and let them dry for 1-3 days, after which you can treat them with a plane, sandpaper and stain them.

• We need a tape measure, a square, lacing and four pegs.
• Place the square on the floor, set it to 90° and draw a line from the outside of the square.

We choose the length of the second corner and measure with a tape measure from the first corner to the second, it should be 2,400 mm. The width of the third corner will be 1.10 mm. We drive in pegs and stretch the fishing line around the entire perimeter.

Inside the resulting rectangle, at all four corners, holes are dug the size of a cinder block (if you decide to put brick in the holes, then it will take four bricks + glue or mortar per corner).

Before placing cinder block or brick in the holes, the bottom of each hole must be compacted with a tamper or cinder block.

Making the floor

First of all, you need to make a frame for the floor from bars. We cut the bars 1.10 mm wide and 2.400 mm long. The corners of the bars are connected to each other with 5x5 iron corners and 35x45 screws.

At least 2 more bars 2,300 mm long must be placed inside the structure along the width and also secured with iron corners.

A board is screwed along the width on both sides and squares from disassembled pallets are attached to the corners; these will be the legs of the house.

The corner posts of the structure are installed at the corners with a height calculation of 1,500 - 1,700 mm, and iron corners must also be used.

After 1,200 mm on both sides we also screw the vertical beams. From the entrance side we add another beam at a distance of 500 mm from the corner post. Lay it on the floor and screw on the FSF plywood, the corners and center of the plywood need to be cut to fit the posts from the timber.

The racks are also twisted together with horizontal bars. We choose the location and size of the windows, screw two horizontal beams at the bottom and top of the window, this will be the height, and two vertical beams along the slopes of the window, this will be the width of the window.

Gable roof

Let's move on to building the roof. First of all, the angle of the rafter leg is measured and the rafters are installed at both ends of the house, they need to be measured, after which you can saw down the rafter legs in the area of ​​the ridge and cornice and twist them on the floor.

The thread is stretched from one rafter leg to the other and the central rafters are installed. In the area of ​​the ridge, under the rafters, another beam is added, so that the letter “A” is formed.

Now we can cover all the walls and the roof of our house with 1.00 mm x 1.200 mm boards from pallets. You need to trim the house with boards horizontally, starting from the bottom, ending at the top, first, from the long sides and ending at the ends.

The excess length on windows and doors needs to be cut down and cleaned so that the baby does not get a splinter and scratch his head when he plays in the house. M

The roof can be covered with either boards from a pallet or plywood. You can also add a ladder to the roof and walls, with small handrails, so that the child can safely climb on the roof of the house.

Children's house two storeys, with swings, slide and sandbox

Who among us wouldn’t want to make our baby not only happy by giving him a one-story house, but also build him two floors with a slide, a sandbox and his own swing. In this version, we will consider just such a house with a small playground.

Material

1. Concrete: Cement, sand, crushed stone;
2. Reinforcement with a diameter of 5 mm and studs, at least a meter long and 25 mm in diameter.
3. Bolts with washers and nuts, screws 75 mm;
4. Boards - Minimum 3,000 mm long, 150 mm wide, 25 mm thick.
5. Beam - 50x50, and beam for posts 150x150 and 3,000 mm long.
6. Swing fasteners, chain, ropes or belts, seat;
7. 500 kg of sand;
8. Caps for bolts and nuts;
9. Iron corners;

Tool for building a playhouse

• Hammer;
• A crowbar or pry bar;
• Roulette;
• Stationery knife;
• Square 30 cm;
• Pencil;
• Shovel;
• Levels: 1 and 2 meters;
• Drill with a cue ball for bolts;
• Grinder with vulcanite circle;
• Wood hacksaw, circular saw, jigsaw;
• Electric or manual plane;
• Thread or fishing line; (lacing).
• Wrenches on (??x??);
• Clamps - 2-3 pairs;
• Wood drill 40 cm long;

Sequence of work

We choose a place of 6x6 m² and prepare the surface of the site.

First, the house is marked, then a recess for the bean box in 20-30 ms and finally, four holes are dug in the corners of at least 700 mm for a concrete foundation.

Concrete is hammered in with the following calculation: 3 parts cement, 2-3 parts squeak, 1 part medium crushed stone. The reinforcement and threaded studs are prepared, the reinforcement is recessed into the concrete, the stud must be at least 350 mm above ground level.

We begin to assemble the skeleton of the house. Corner posts, 150x150 by 3,000 mm long, are screwed onto studs, leaving a small gap of 10-20 mm between the post and the floor. The studs are lubricated with machine oil or grease.

Horizontal beams are measured, to tie the pillars together, at the bottom under the sandbox and at the top under the second floor floor buildings, 1,500 mm from the sandbox. The entire skeleton of the house must be twisted through the fasteners and into the ends of all the beams through the pillars. You can screw FSF plywood 20-30 mm thick to the bottom of the sandbox, so that no matter how much sand goes into the ground, grass does not grow and there is no soil in it.

The construction of the second floor starts from the floor! The sheathing must be done, and the boards are screwed with 45 screws, 150 mm wide, 25 mm thick. Windows and doors are measured, and timber is installed around their perimeter.

The slide is assembled in the form of a ladder from a beam using screws, The same boards are screwed along the stairs as on the floor of the second floor. The railings on the slide must be held tightly so that a child does not accidentally break them off, so it is worth securing one more beam along the railing on each side.

Before attaching the swing, you need to measure all the angles, file them down and collect it on the floor. Align and screw the central horizontal beam, first to the house, then to the top of the base of the triangle.

Do not forget! About safety precautions and the safety of your children. All parts must be twisted through the corners, and all existing fastening systems. Bolts and screws should not stick out from the tree, so that your child does not get hurt.

The roof begins with measuring the rafters and their angle. Three triangles are assembled on the floor, two of them are fixed to the bars of the skeleton of the house. A fishing line is attached to them and a third one is installed between them.

Now you can begin to cover the outside walls and roof of the house with boards. In the nutria it is also worth placing small benches on both sides near the windows. You need to screw the boards onto the roof with a slight overlap of 10-20 mm.

• This house can also be painted or covered with stain and varnish.
• We fix the swing, fill it with sand and call the baby loudly.

Children's house for a large family with a sports ground

1. Why plywood
2. What to pay attention to
3. What to pay attention to
4. Let's get to work
5. Additional functions
6. Let's sum it up

Apartments for dolls are often expensive and are made of plastic - a fragile material that breaks easily. The article describes how to make a toy house with your own hands.

To make a child's dream of a house for his favorite doll come true, it is not at all necessary to go to the store. You can make a cottage from your own design.

Arguments in favor of self-production

Why you should build a homemade dollhouse from plywood:

• Individuality. The project will be unique.
• Working together with a child. Helps strengthen family relationships.

• Development of creative abilities, skills, motor skills, acquisition of new experiences by children.
• Possibility to create a house of any size.

Why plywood

A dollhouse is made from different materials. The best option is plywood:

• The use of plywood for construction ensures the strength of the future home. When fastened well, the parts do not fall apart or break off.
• Plywood is easy to process with conventional tools.
• Wooden toys are pleasant to the touch.
• The beautiful appearance of wood allows you to do without additional decoration or surface design.
• Low material cost.

What to pay attention to

Formaldehyde is used in the production of plywood. They are part of the impregnating adhesive for joining fibers. To avoid poisoning or hazardous material getting into the children's room, you need to pay attention to the markings of the sheets:

• E0 - less than 6 mg of formaldehyde per 100 g of product;
• E1 - 7–9 mg per 100 g;
• E2 – 10–20 mg per 100 g.

Furniture and its components must be made from the safest class of plywood - E0.

How to do

Making a house for dolls from plywood is a multi-step process. A certain sequence of actions must be followed. To make the work easier, you can use step-by-step instructions.

Stage 1. Sketch preparation

The diagram should show the layout, floor dimensions in length, width, height.

You can find a sketch on the Internet and adjust it. The photo shows several basic diagrams of a toy home.

The most important thing is to maintain the proportions of the sizes to scale. This is necessary in case you want to change the dimensions of the product during operation.

The design can be thought out in advance in order to purchase and prepare the necessary materials for decoration.

Stage 2. Preparing accessories and tools

For assembly you will need:

• Plywood. To determine its quantity, use a drawing: calculate the number of parts, their sizes, and obtain the total surface area. Based on the result, purchase the required number of sheets. For a tabletop house you will need 2–3 blanks; for a large mansion it may take up to 7–10 sheets of plywood.
• Corrugated cardboard for the roof.
• Tool for cutting wood. It is recommended to use an electric jigsaw. It will help you quickly and accurately cut out parts of the desired shapes and dimensions.
• Wood glue for fixing assembly elements.
• Mounting tape as an aid for fastening parts.
• Fine sandpaper.
• Tape measure, ruler, pencil for marking.

For registration you will need:

• PVA or silicate glue.
• Wallpaper, color films.
• Self-adhesive film to imitate flooring.
• Colored cardboard or paper for decorating individual elements of the premises (optional).

Stage 3. Image transfer

To assemble wooden parts into a single whole, they must be cut from a blank sheet. To do this, scale sketches are transferred to paper, finished parts are cut out of it, and later used as a template.

If the windows are not indicated on the diagrams, they are drawn when transferring the patterns. On a flat-looking house without a front wall, cuts for windows are not needed.

Stage 4. Assembly

Step-by-step assembly instructions:

1. The parts transferred to the plywood are cut out with an electric jigsaw. They try to do this carefully, without going beyond the contour lines: if there is a mistake, the structures may connect incorrectly.
2. Sand the edges to make the parts safe and avoid injury.

Cutting and finishing of edges should be done by an adult.

1. Assembly begins with combining the interior space. Floors and internal partitions are attached to the vertical end walls using glue and mounting tape according to the diagram. To strengthen the connection, the inner corners are glued with thin slats. They will add rigidity to the structure. At this stage, the child may be involved in the work.
2. Flights of stairs are made of wooden rulers. They are placed in the form of slides or cut one and glued together into a real staircase.

1. Attach the back wall.
2. Assembling the roof. You can cut out whole slopes from cardboard and glue them together. Another option is to assemble the roof from individual pieces in the form of tiles.

The finished frame of the house is left for several days until the glue dries and the structure acquires sufficient strength.

After assembly, the design begins.

Stage 5. Design

The finished frame is decorated and furnished with doll accessories. Recommendations:

• The floor can be left as is or decorated. Plywood has a wood pattern, so covering it with a similar pattern is impractical.
• You can make hinged windows and doors. To do this, lay the canvas on pieces of cardboard or use small metal door hinges. The passages are covered with fabric curtains. Windows are sometimes replaced with cardboard shutters.
• The ceiling and walls can be covered with colored films, wallpaper, or painted.
• Furniture for toys is placed in the rooms.

Additional functions

Not only the aesthetic, but also the practical side of the house is important: toys need to be stored somewhere, accessories need to be put away, something needs to be hidden. You can make additional built-in drawers in the upper or lower tier. This is appropriate if the house is large and takes up significant space in the living space.

Boxes are also made from plywood. The drawing provides space for storing things. The sides of the box are cut out of plywood and glued together. Screw the handle and insert it into the compartment.

You can make a hinged door like in the photo. To do this, the cut canvas is screwed onto metal loops.

Conclusion

A homemade plywood toy house will be a good gift for any child.

The construction process will take 2–3 days, taking into account the preparation of blanks, their cutting, and drying of glue. The child can decorate the premises independently.

Children don't need much to be happy. We buy toys for children from the store, citing the eternal lack of time and energy that prevents us from doing something with our own hands. For example, a children's house made of wood, in which children could play all day long, while at the same time spending this time in the fresh air. By making a wooden house with your own hands, you will definitely make your children happy!

But adults will need few materials. As for personal time, you will have to spend a couple of days on “construction”. And don’t forget about reliable helpers, because the child will take part in the construction of his own home with great enthusiasm.

DIY plywood house

Many people underestimate the capabilities of ordinary plywood as a building material. But if you build a structure using it for your little daughter or son, it can even stand on the street for several years. The main thing is to properly process the plywood sheets and related materials. It's quite easy to make a playhouse with your own hands from plywood. Pressed sawdust has excellent moisture resistance characteristics when properly processed.

Chipboard is a durable and affordable material; it is ideal for building a children's playhouse. Chipboard is easy to process and achieve the desired look. If the house is being built for a daughter, it can be covered with colorful or pink wallpaper, if for a son, it can be covered with decorative wallpaper with a car-themed print. In general, the field for imagination is huge; the main thing is to have the desire to realize your ideas, after consulting with your child.

In addition to chipboard sheets, you will need wooden boards, nails and screws. And also a small door. The door is also made independently using wooden boards and metal hinges.

Where will you need a house?

Before you start “building” a house, you should decide on its purpose. This factor will depend on where the house will be located and in what seasons the child will play there with his friends.

We choose the following options:

• house located in a residential area;
• house for playing in the warm season;
• demi-season option.

These factors will influence the need for glazing windows. insulating walls and installing a small heater for those who like to drink tea in the fresh air in winter.

A house for children is placed in a nursery or playroom. The child spends a fair amount of time in his “home” and may put some of his toys there. This option requires a minimum amount of building material. Rather, the house performs purely decorative functions, and can almost entirely consist of beautifully decorated plywood. It would be easiest to make such a house with your own hands.

The house is also placed in the courtyard of a dacha or private house. The building is used only in the warm season. Its windows do not have to be glazed; sometimes there is even no need for doors. It is enough to make the appropriate holes in the structure made of plywood and wood.

But you can build a children's house with your own hands for all-season use. The walls can be slightly insulated, the windows should be glazed, and the door should close tightly. At least in winter you can drink tea with friends in such a building. You can even install a small electric heater here.

Depending on the chosen house option, additional materials will be used:

• glass;
• mineral wool for wall insulation;
• electrical wiring elements.

Deciding on the sizes

The size of the house will depend on the age of the child. A children's wooden house may be small in size, but do not forget that the child is growing, and in a couple of years the structure will have to be dismantled if it now has parameters of 1.5X2.

Do you want to build a more durable house for your daughter or son with your own hands? Then you will have to make structures at least two meters high. Plus the roof. The total height of the plywood will be 2.5 meters. This is for the front part. For side walls, sheets 2 meters high are suitable.

The width of the walls will be 2.5 meters. This is quite enough to place some furniture and toys inside the house.

Materials

Before buying materials for the house, you should decide what floor it will have. Let's focus on the EU version with a wooden floor, which is suitable for an outdoor house. The floor on a small hill made of logs can also be used in the cold season. The parameters of the structure may vary, so we provide only a list of materials required for construction; you yourself will be able to more accurately determine the dimensions of sheets, doors and the length of the boards. This is quite simple to do; the design does not require complex calculations.

So, we prepare the following materials:

• four sheets of plywood;
• four logs, they will be located in the corners of the house;
• wooden logs with a width of at least 10 cm, at least six of them will be required;
• wooden boards 1.5 - 2 cm thick for making floors;
• thinner roof boards.
• boards for finishing and sealing walls;
• material for the manufacture of window frames and door frames; if the windows are glazed, wooden slats and glass will be needed;
• door on hinges.

A children's house can also have a metal roof.

You also need to take care of the lighting in the house. Then you will need a wire to connect the electric lamp. You can run LED strips around the perimeter of the ceiling; this is the most economical and safe option. It’s quite easy to do the wiring yourself; as a result, the wooden children’s house will be illuminated in the evenings, which will delight the little household.

Building a wooden house

First you need to make the floor. It will also act as a base. Due to the fact that the floor is mounted on joists, the structure can be moved from one place to another if necessary.

Instead of nails, it is better to use wood screws instead of ordinary nails: this way the structure will last longer. In this case, you will have to arm yourself with a screwdriver.

When the floor is ready, we install the frame. First - corner logs, then - boards, which will subsequently support the wooden roof. Plywood sheets are attached to the outer sides using screwdrivers. The roof is covered with boards in the same way. You can also use plywood to make it, but it will quickly lose the properties necessary to protect the house from constant exposure to water and sunlight.

On the walls we outline places for windows and doors, outline them and install frames. We install doors. We strengthen the structure by installing additional narrow boards. The best option would be to install the boards vertically on both sides of the windows. A DIY children's house can be covered with wallpaper from the inside or painted with funny pictures.

Video gallery

Building a children's house with your own hands is simple and exciting. Having already gained experience in construction and repair, you can put this structure in the proper place in a day; “from the end” - over the weekend. Construction costs will be at least three times less than buying a ready-made one, and the benefit from it will be great: the desire of the younger generation to build “halabuds” has been biologically embedded in us since those times when the ability to build a temporary shelter from scrap materials was a matter of survival, like the ability to hunt or distinguish edible fruits and roots from inedible ones.

We are not primitive for a long time, but our children still need a playhouse - it is one of the means that contributes to the formation of personality, the acquisition of skills and abilities, and physical development. The playhouse will occupy little fidgets with full awareness of their importance: having their own territory and living space, they will not bother adults for irrelevant reasons, just to remind them of themselves. And dad, mom, and guests will be able to calmly go about their adult affairs or just sit at the table, without fear of generational stratification and hidden tensions in the family.

What to build?

A house for children is built, firstly, taking into account the characteristics of child psychology. As deep as, for example. at , in this case there is no need to delve into them, but it is necessary to take something into account. Secondly, the nature and duration of use matter, namely: in an apartment, a house or on the street, personal for your children, perhaps with their friends, or shared in the yard, it is designed for one generation until it grows up, or for a long time use. Thirdly, the gender of the child: it is common knowledge that girls and boys behave differently from infancy onwards.

The construction of a toy estate for offspring is unlikely to cause difficulties for “dummies” parents: the small size of the structure will help here. They affect not only the savings in materials. We will return to this later, but for now let us state: the main task in this case is to decide what exactly to build. The offers of “orphanages” for sale make your eyes widen, but the overall impression is as if you were in the 17th-18th centuries, when children were sewn the same caftans and trousers as adults, only smaller. This applies not only to the appearance, but also to the technologies used, on which the price of the product directly depends.

Children today, in appropriate circumstances, wear clothes of an adult cut, but they are not intended for play! A house for a child should be made based on the fact that they will play in it. Yes, children's games are preparation for adult life, but not learning it from instructions. A child is not a robot that needs to be “tweaked”; he is a full-fledged member of human society and can organically enter it himself, demonstrating his abilities and achieving success thanks to them. One of the most important features of the child’s psyche is the combination of pure pragmatism with unbridled imagination. Taking this into account, children's playhouses can be considered in a certain order, see fig.

Like adults

House on can conditionally be called “master’s”. It is built from wood as the most environmentally friendly, affordable and easily processed material. Durability, without careful impregnation and protection from soaking, will be at least 7 years in central Russia, which is enough for the house for its children - they will grow up during this time.

The “master’s” house is a universal structure: the inhabitants themselves have the opportunity to equip it according to their taste, needs and abilities, unobtrusively learning at the same time to invent and make with their hands. Imagine, for example, a mast with a sail on the roof - it will not be difficult for a child’s imagination to complete the rest to the “Black Pearl” or “The Walrus” of Captain Flint. We remove the yardarm, hang a flag on a pole - there you have a castle, and that snag is a fire-breathing dragon from which you need to save your sister or princess friend. Anyone who remembers being a child will come up with a lot more.

The “master’s” house is, in general, an imitation of an adult house of a simplified design; its typical layout and dimensions are shown in Fig. on the right, but we’ll see how to build one later. An indispensable feature is the enlarged window openings. It's not just that it's more convenient to play this way. Human vision is formed in childhood; In order not to spoil it from a young age, you need to follow medical instructions on the amount and nature of illumination. And when the size of windows decreases, their area transmitting light flux falls by the square of the size of the window. In order to withstand fluctuations in illumination within acceptable limits, especially when moving from the street to the house and back, the area of ​​the windows relative to that of the walls in the children's house must be larger.

– “master” modification in the form of a gazebo for sanguine/choleric extroverted children. They often have the makings of a leader; to fully develop, they need to keep in mind their surroundings. For children who are somewhat (not to the point of autism, of course) withdrawn and self-absorbed, a “house on chicken legs” is more suitable. . Let us remember that children are pragmatists to the core. For them, the aspiration of thoughts to the heights of the earth is associated with a real distance from the earth's firmament. But don't forget about lighting! Do you see the windows on the roof? These children don’t like big windows, but they need light. And on the roof - nothing, there is the sky, clouds. There is somewhere to direct your visual and mental gaze. Dreamer children tend to lack exercise; in this case, this problem will be solved by itself in the form of a ladder, and the slide will remind you of simple everyday joys.

Outdoor sandbox house - for the little ones. There is a shelf - they themselves will understand that it is more convenient to put toys there, and not throw them anywhere. And it’s more convenient for adults to collect them from there, rather than pick them out of the sand. However, sandboxes are a different matter.

Little ladies

For girls, a stall house is more suitable: a gazebo with higher sides, , or “master” with a veranda-counter and a window facing it, . There's nothing you can do about it, girls love to play bargaining. No matter who they grow up, they have to manage the household, and purchasing is a rather delicate and responsible matter. Therefore, the girl’s house, in the yard or in the apartment, , must be equipped with shelves for goods, scales, etc. For lessons without interrupting your work, the shelves are also suitable.

For girls, the style and decor of a house is more important than for boys. The “gingerbread” style is more suitable for stay-at-home mom’s helpers, . Design kits for assembling gingerbread houses are on sale, but it is not necessary to assemble them from purchased plastic parts: a typical owner’s house can easily be turned into a gingerbread house using scraps of plywood, boards, a jigsaw and paint. He needs simple but constant care, and that’s what little busybodies need.

For artistic people with the aspirations of a future pop diva or socialite, something less substantial (artistry is inextricably linked with the desire for a change of scenery), but more colorful and glamorous, will be more suitable; perhaps somewhat tawdry, . Just don’t decorate such a house right away on your own: artistic people have a healthy imagination, but individuality is clearly expressed, and self-discipline is often lame. Give her a foundation, an impetus, and then let her work for her own pleasure and improve herself in the process of work. Read more about this later when we get to cardboard houses.

A special case are tomboyish girls who are on first terms with boys. They speak “you” on “you”, but they understand that they are not boys after all. Therefore, their demands are higher and more unique. A house for a tomboy girl is a special case; like, for example build a playhouse for a girl like Pippi Longstocking, see

Video: house a la Pippi Longstocking, “Hacienda” program

To make it really cool

It’s easier with the boys: if it’s not possible to build a master’s building, they will be completely satisfied with a shelter with a ladder and a climbing frame under the porch or in a corner, . The ultimate desire of any boy is a tree house, . If you have something suitable in mind, incl. and for safety requirements, a tree, and how to build a house on it, see the video:

Video: tree house, “Dachny Answer” program

But this is rarely found on a personal plot or dacha, especially since you need to hammer nails into it; The fruit tree may die from this. In this case, you can make a children's treehouse without damaging it, as shown in Fig. left. Instead of a roof, you can hang a tent tent, as described below, or make it a hut.

A complete replacement for a tree house, “completely cool” according to children’s concepts - a hut, . However, it requires quite a lot of natural material and the ability to assemble it into a reliable structure. Therefore, instead of a hut, it is better to build a hut, . We will return to “realistic” huts for children later, but for now in Fig. on the right is a drawing of a 2-level hut house. It is strong, resistant, it does not require a base; it is simply placed on the ground. There is only one drawback: you need more space than for the “master’s” house. Assembly technology:

• A-frames are made to size from 150x75 timber. The corners are fastened with M10-M16 bolts, see bottom right in the figure, with nuts and washers with a diameter of 40-80 mm. Figuratively speaking, all the rigidity of the triangle falls on its corners, and nails/screws in this case will not be reliable enough;
• lay the frames on their sides one by one and sheathe the upper corner with 2-3 belts of boards, obtaining a frame blank. You can do more without bringing the sheathing to the 2nd level floor, but it will only be more accurate. The perpendicularity of the plane of the frames to the ridge girder is controlled with a square from 0.5x0.5 m;
• also controlling the perpendicularity, sew on the 2nd level floor board on each side;
• put the workpiece on its feet, it is already quite rigid. They put something under the sagging legs, or dig them into the ground until the ridge run is horizontal; check the level;
• lay the floor (board 100x40 or 150x40), make a staircase, partition, climbing frame, etc., finish covering the slopes - ready!

What if there are two? Or a crowd?

What to build if there are two or more children? Different sexes and different ages? The simplest option is phytobuilding, , everyone will like it. But, alas, phytoarchitecture grows slowly, and you need to think about a phytohouse long before the birth of your first child, even if you plant clematis on the base trellis.

Prefabricated option - 2-storey house, . This is an ideal playground house, see e.g. rice. on the right, but it requires a fairly strong foundation. Let's see how to do it further. Actually, a full-fledged children's play complex is a separate article; just in case in Fig. Below is a typical diagram of its structure and dimensions.

If the children are a boy and a girl with a small age difference, then the floors of a 2-story house need to be equipped according to their needs, . In this case, the house must be built from boards at least 30 mm thick: a light structure, designed for a neat girl, will not withstand boyish loads, and a rough one made of timber or logs, see below about fairy-tale houses, is unlikely to suit the taste of a refined nature. If she is alone, then she will most likely approve of Baba Yaga’s hut, but in front of the opposite sex she will be indignant at the “brutality” of the structure, if only out of spite.

Maybe you don't have the desire and/or ability to do excavation work. Let's say there is nowhere to put the house except on a well-groomed lawn. In that case, compare . Hut? Hut. But quite modern. Made using the “master’s” technology, see below, only the facades are assembled in frames with curved elements. It is more difficult to assemble these from slats, but the roof is simplified: in this case, the roof is a simple plank sheathing. And its configuration gives (especially in the children's imagination) a virtual 2nd floor with a slide; the steeper slope is a climbing frame, as it was there.

And at the dacha?

A children's house in the country is most often a type of tent. There is no particular point in building a permanent house there, unless it is an elite dacha and the area is protected. The simplest tent is made from a sheet, bedding and rope, . There are also a lot of children's tent houses on sale, , but these are easy to make yourself by fastening a frame of metal-plastic pipes (easily bent in any way) in several places with tape. The same method is applicable for apartment tent houses, which we will return to later. If there is a lack of natural supports or material for them, you can put up a corner tent, see figure on the right. The inset in it shows different design options.

The second option is a tent-hut, also known as a folding tent. The design is clear from . Boys like these more and are still more hygienic than a hut. Although doctors are unanimous in this regard: children from whom, as they say, dust particles are blown away, are more likely to grow up frail, painful and unsure of themselves.

A wigwam tent is much more romantic and suitable for both sexes. pos. 22. To prevent it from being stuffy, there should be a gap at the bottom and a hole at the top for ventilation. How to set up a tent or wigwam, see below. Finally, a more girly design is the marquee tent. It’s easy to install it, see fig. on the left, and a view of . If the daughter declares that she does not feel like a queen of Shemakha in him, then she is simply breaking down.

Fairy tale or true story?

A special type of children's playgrounds are fairy houses. Similar to those on , you can build it yourself from available materials. But, unfortunately, their gaming functionality is extremely narrow. Re-read The Adventures of Tom Sawyer. How many games did they play with Huck Finn in one summer? But even a child’s imagination will save you if you need to turn a pirate ship into Robin Hood’s cave. Unless your position allows you to order the butler: “Samuel Sigismundovich, please make sure that by tomorrow morning the house-ship is replaced by a house-castle.” It is unacceptable to zombify children in a single-line manner, because they will grow up. And what prospects could there be for a society populated and governed by moral monsters?

There are also fairy-tale houses with quite wide functionality, eg But behind their apparent simplicity lies a very complex technology of creation. Their production begins with computer modeling of the design.

Log, timber, slab

You can make a good fairy-tale wooden house with your own hands in a rustic style, i.e. rustic style. But here it’s time to dodge. For example, a product for impresses both children and adults. The latter are more expensive, somewhere around the one-room apartment in a new Moscow building. But it will be too late to look for the material yourself, not only for the children, but also for the grandchildren. Moreover, driftwood suitable for rustic creativity is highly valued, its miners earn much more than treasure hunters with metal detectors, they have a trained eye, they clean up fancy stumps, dead wood and dead wood from the forest.

A hut on chicken legs made of timber or logs, , is already more accessible. But in order to build it, you need to be able to erect a log house, and this is a rather complicated matter. For the gingerbread chopped hut, , the difficulties are at least tripled. If there is simple dead wood in the vicinity, you can build a gazebo hut, , however, the waste from pruning the garden is no longer enough for it. In this case, a cheap waste product from sawing timber - croaker - will help out. Debarking it is quite a labor-intensive task, but not difficult. Then - 4 pillars, poles, some boards for the floor and steps, and it turns out something like what is on . Quite rustic, cheap and cheerful. By the way, a roof that goes better with a hut is not a hip roof, but a much simpler gable roof.

How to build?

There is a sometimes harmful and sometimes useful law of the square-cube in technology. Its essence is that when the size of something increases while maintaining proportions, the volume of the thing increases along the cube of linear dimensions, and the cross-sectional area, cutouts, openings, grooves, etc. – according to their square, i.e. slower. In it, by the way, lies the answer to a question that often baffles young sailor cadets and shipbuilding students: why does a wide 7-meter pleasure yacht with a heavy false fin go with a strong list in a fresh wind, while a narrower one, with a larger relative sail area and without any additional means of imparting stability, a 70-meter barque - almost without roll? Only in this case the square-cube law is transformed into the law of 3-4 degrees, because both heeling, from the wind pressure on the sails, and restoring, depending on the volume of the immersed part of the hull, moments must also be multiplied by their shoulders, which have the dimension of length.

When applied to a children's house, the square-cube law works for the builder, allowing it to be built much more simply, using less material, but no less reliable. Let’s take, for example, a load-bearing beam half the size of an “adult” one. Its volume (and its own weight) will decrease by 2^3=8 times, and the cross-sectional area supporting the load will decrease by 2^2=4 times. Because the beam must also support its weight; an excess load-bearing capacity appears, which can be used to simplify the design. In addition, the elongation of the beam also changes, i.e. the ratio of its length to its greatest transverse dimension. The distribution of stresses in the part significantly depends on elongation: their diagrams can change dramatically, although the beam looks the same, only smaller. We use these and some other circumstances to build a children's playhouse easier and cheaper.

Base

A children's house does not need a foundation as such at all. If you want, install at least a monolithic one with a basement, it won’t be worse. But in general, it’s unnecessary, and on any kind of load-bearing soil, except for muddy and subsiding soils, but there is nothing for children to do there - it’s dangerous.

The point is, firstly, the bearing capacity of the soil. According to the square-cube law, the load from a house with a raging horde will not exceed 0.2-0.3 kg/sq. cm, you can count. And any more or less load-bearing soil holds from 1 kg/sq. cm; in extreme cases - from 0.5 kg/sq. see. The supply is in any case more than sufficient.

Secondly, in the peculiarities of frost heaving of the soil. On an area up to approximately 5x5 m, it is almost uniform: no obvious bumps are formed, the entire area rises by several cm in winter, and returns to its place by spring. Even a permanent structure will not feel this, and the rigidity of the children's house due to the lower elongation of its parts is higher.

Therefore, the children’s house can, after first leveling the site, simply be placed on scraps of timber (item 1 in the figure), concrete blocks (item 2), bricks, etc. Supports are still necessary to prevent the floor from rotting, but, as we will see below, they can be included in the design. Another facilitating point is that you don’t have to level the site, but choose a suitable natural one based on measurements. Construction slopes are standardized in mm/m (up to 3 mm/m or 0.003 for residential premises). For a house up to a maximum of 3x4 m, the permissible initial slope in degrees will be correspondingly greater and, due to the increased rigidity of the structure, safe.

What is really necessary to prevent rotting is treating the base from the bottom, i.e. on the side facing the ground, pos. 3. The best impregnation is natural, heated in a water bath, drying oil or special impregnating oils for wood. As a last resort - mineral oil or waste, but then small fish can be allowed into the house no earlier than 2 weeks after completion of construction. Anyone who has experience with children will probably immediately prefer drying oil.

It is best to leave the upper side of the base “bare”, untreated, pos. 4. If it is going to be painted, it needs to be dried or impregnated with a water-polymer emulsion or PVA diluted 3-5 times or more. The latter is preferable for a budget option: 0.5 kg of a can, shaken in half a bucket of water, is enough for the entire house.

What about supports?

For a house on chicken legs and, especially, for one shared on the street with a sports and gaming complex, a more solid foundation is required, otherwise the naughty brethren may knock it over on themselves. That is, the supports of the house, wooden or steel, need to be buried in the ground from 0.5-0.7 m in the first case and from 1.2-1.5 m for a collective use complex.

The technology for preparing the base in this case is usual: the lower ends of wooden supports for a length equal to the depth of the depth + (10-15) cm are treated with bitumen mastic or liquid, without filler, hot asphalt (tar). Steel ones are doused with the same tar; both are wrapped in roofing felt and dug in or concreted. A sand cushion of 10-15 cm is poured under the heels of the supports. Wells for the supports are drilled with a garden drill with a diameter of 20 cm, so that the supports fit into them at intervals of 3-5 cm, counting from the edge or corner of the pillar.

If you need foundation durability of over 15 years and don’t want to bother with concrete, the lower ends of wooden supports of the same length should be burned over a fire until charred to a depth of about 5-7 mm, continuously turning over the fire. Such a foundation is especially reliable if the supports are made of pitch pine or oak logs. During excavations of Ancient Novgorod, wooden burnt foundations of buildings were found in abundance and, according to the conclusion of construction specialists, a considerable proportion of them remain suitable for construction.

There is a trick to burning wood for a foundation: suddenly the wood catches fire, under no circumstances should it be extinguished with water. You need to knock down the flame with a felt or sand, extinguish the smoldering coals in the sand, and continue firing.

Design

The optimal technology for constructing a children's playhouse is a prefabricated panel house using a single power circuit. It is also possible to build a frame house, like a country house or, but it will be more work. The step-by-step instructions for building a prefabricated panel children's house are simple, see fig. below:

Prefabricated panel technology is suitable for modular construction without significant changes. For example, in Fig. Below are drawings of a 2-level house with a separate porch. A whole brood of 3-4 noisy “chicks” can play in this one. The elevation of the base above the ground can be increased by increasing the height of the above-ground part of the supports to 1.2-1.5 m.

When building, first assemble the bases and place their feet in the pits. Then they are leveled, adding/removing bedding, and the wall frames are placed and sheathed.

Rafter trusses are assembled according to the usual A-shaped pattern, see fig. on the right, placed on temporary jibs. Then they make a ridge from a pair of boards, at the top in the figure, remove the jibs, and lay the sheathing under the selected roofing material. The rest is as before. case.

Country-plywood option

A children's playhouse made of plywood panels is well suited for a summer cottage: for the winter it can be disassembled and folded into a compact package, stored indoors. Assembly is carried out in a way that is well known to fans of Chinese puzzles: using grips. This type of connection is also called “deep paw”, because it works in general the same way as connecting the beams of a log house into a paw.

The assembly order and connection method are shown in Fig. below. There are 2 tricks here. First, the toes of the long walls should be facing down, pos. A. Second - the edge of the last roof sheet in the order of assembly should overlap the edge of the penultimate one, pos. b. Then, not knowing that to disassemble you need to press the last sheet and move it upward diagonally, you can even turn the house over, and nothing will happen to it. And assembly/disassembly will only take a few minutes.

Hut

In terms of excitement, gaming functionality and psychological and educational significance, a hut in the garden is in 2nd, if not 1st, place in the hierarchy of children's houses. How to make a regular hut-tunnel is clear from the figure:

If there is no spruce branches, but there is hay, straw, and reeds, it will be easier to build a hut-chalet, see fig. on right.

Actually, “hut-chalet” is a tautology; "chalet" in Russian is a hut. Flexible rods or wire are placed in the flyers of the chalet frame. It is not necessary to fix the top of its frame with a thin bucket: if the support flyers have forks at the top, they can simply be hooked onto each other, see fig. left.

Bundles (sheaves) of sheathing material are hung on protruding knots in rows, starting from the bottom. To make the sheathing smoother, it is advisable to take the strapping rods with knots; sheaves are also hung on them.

The pinnacle of hut construction is a wigwam hut or a conical hut with a neck; it is never stuffy in it. The installation method is shown in Fig. below. If the lower ends of the poles are placed in a trench and covered with excavated soil, it will stand for more than one year. You can also install a gazebo for adults in the same way. Having decorated it with taste, we will see a new meaning in the famous “The rustling of silks in the hut...”.

It is advisable to add something to the hut for children's games. Child psychologists joke that a normal child should be able to get dirty even in a sterile medical room. There is no big problem in this, see at the beginning, but sometimes the little ones crawl out of a hut with a straw bedding, extremely grimy. So that adults have less hassle with washing and washing, it is better to place the children's hut on a platform. It is easy to arrange between trees, see fig. on right. And for the kids, it will immediately acquire the reputation of a tree house, which couldn’t be cooler than that.

Cardboard houses

It makes sense to make a children's house made of cardboard, firstly, for the little ones, crawlers. They have absolutely no requests for decoration (their little eyes are not yet fully visible), but they are growing quickly and will soon outgrow a solid house. The “construction” comes down to an unnecessary cardboard box, pos. 1 in Fig.:

Secondly, for artistic natures, poses. 2. A hook so that eccentricity turns into determination; in this case, the most eye-catching and technologically complex components are window and door frames. And then - create, invent, try, mom and dad will help. It’s a complete fiasco – no problem, we’ll make a new one with whatever cardboard there is.

Another option is a garden and country house, pos. 3. Do you think it's fragile? And there is plywood glued to the bottom and ceiling from the inside, it will withstand the season. If there are foam shipping inserts left from the contents, even better. Glue them onto PVA, turning the flat side inward. You just need to cover it with plywood or the same cardboard: it’s foam plastic, after all, but how can you not pick at it if it can be picked at?

House in the apartment

A child’s playhouse in the apartment is also necessary. And it is even more necessary if the family goes out of town sporadically. There is a place for a children's corner; it is advisable to build a permanent house there, from plasterboard on a wooden frame or plywood. Construction technology – conventional, pos. 1-3 in Fig. There is a place, it is advisable to make the booth larger so that a working corner fits in it; Children need privacy and peace during classes, just like adults. In this case, you can equip a loft bed on the 2nd floor.

A temporary option for an apartment children's house is a tent. Plastic pipes will be used for the frame of a homemade wigwam, pos. 4, and for the house tent - bent metal-plastic, fastened at the corners and in the middle with tape, pos. 5. Once assembled, these houses need storage space. If there is a lack of it, you can hang the tent of the Shamakhan queen, like in a garden. True, not all boys like him. To hang the tent on the closet, you need to place a pipe rod that is securely fastened. So as not to interfere when not needed, it is made rotating, sliding, telescopic, etc.

Do you need papers?

A children's playhouse, unless it is on a foundation, is not a building structure under the law, nor is it real estate. In fact, this is a homemade toy not for sale, the production of which is not regulated in any way. It is still possible to “tighten up” gaming complexes to accommodate sports equipment with all the requirements for it, but as the litigators say, if there is a clue, there will be an excuse. Therefore, the documentation of a yard children's house for collective use is extremely simple, and is not at all necessary for personal use.

If the house is intended for all the surrounding children, its design consists of the following sheets. On the sheet - on the views of the facades of each module, with cross sections and a plan, as in the figure, and for the modular one, a general view; possible in isometry. That is, for a house with a porch you need 3 sheets, and for a simple one - 1. Another one is for a diagram showing the location of the house on the site. These sheets are shown to the representative of the company managing the house, or, if the house is in the collective management of the residents, they gather their general meeting and present it to him. A permitting resolution from the manager or a resolution in the minutes of the meeting is sufficient for the house to gain full legal force. As for the rest, as long as the children like it.

Almost all adults in childhood built small buildings that resembled a house. For children, this is an ideal place where they can play, relax and do interesting things. Of course, you can make a hut from branches or a structure from cardboard, but the service life of such products is very short. Therefore, it is better to build a high-quality children's house with your own hands for a long time than to constantly build dilapidated buildings.

A little about the wooden house

For building a house for children They often choose wood materials with their own hands. From an environmental point of view, it is safe. Although the material, unlike stone, is characterized by less durability, a wooden house will last at least several years, and if you use a special impregnation, the service life will increase significantly. Preference is given to coniferous trees. They're not just environmentally friendly, but also have a positive effect on health. A house for a child is necessary because in such a place he can develop and feel independent.

The main task of parents is to make a children's house with their own hands without a lot of money, safe and aesthetically pleasing, so that it fits into the interior of their summer cottage. In addition, the building can be used as a warehouse and equipment can be stored there, however, if the dimensions of the house allow this, and the garden supplies will not destroy the building.

Initially, you should think over a work plan and make a drawing. You need to know in advance what style and size the house will have and choose the material for construction. To draw up a plan, you must adhere to the following points:

• decide on the type of building - closed or open;
• choose an area for construction in the country yard - whether the building will be on a tree or on the ground;
• choose a material that won’t hurt your pocket, but it’s also important not to go cheap;
• will there be doors and windows, and what material will they be made of;
• will other objects be built that will be attached to the main house, for example: stairs, fencing, slide and sandbox;
• what roofing covering will be used for the roof;
• choose the paint colors in which the building will be painted;
• decide on the interior decoration.

There are many options for how to build a mini country house with your own hands. Mostly parents prefer the following ideas:

• forest hut on a tree;
• nomadic yurt;
• Hobbit House;
• Indian wigwam;
• house in the shape of a pirate frigate;
• Robinson's hut;
• antique mini castle.

In fact, you can come up with a huge variety of ideas. But if the family budget does not allow such a dream to come true, then a house made of fabric or a hut made of branches is chosen as a budget option.

DIY small country house can be made with a hip or hip roof, have more than 3 windows, a second floor equipped with a balcony and a porch. But according to the standard, the plan looks like this:

After creating a working plan and choosing a building style, it is recommended to make a drawing and sketch (sketch of the house). If you don’t want to do such work, then ready-made drawings can be found on the Internet.

After planning and creating drawings with estimates, you should purchase materials and tools for the job. So, what supplies will you need to build a mini house:

Step-by-step construction of a mini-cottage

So, the work plan has been thought out, materials and tools have been purchased, a drawing has been drawn up, a site for construction has been selected, which means we should get to work. Typically, professionals build such mini buildings in a few days. If you have no experience in such matters, then you should not rush and speed up the work. It is important to make the house not only reliable and durable, but also smooth and beautiful.

You must understand that this is not a large-sized cottage of 150 square meters. m., but a small children's building that does not require a reinforced foundation. It is enough to dig a 60 cm deep ditch along the perimeter of the future building and lay a foundation of brick or cinder block. It is also possible to use wooden supports, but they will quickly rot. Therefore, a stone base is the ideal solution.

However, if for some reason it is difficult to purchase a cinder block or brick, then it is recommended to use rubble or wild stone. The material can be found anywhere. But in this case, concrete mortar and pouring of the foundation will be required. However, it is cheaper.

Installed on top of the base wooden frame from beams. The structure is secured to the foundation using anchors. It is important to first lay a layer of roofing felt under the wooden frame - this prevents moisture from getting on the tree.

Construction of a wooden frame

The frame is assembled from beams, which are attached to the frame on the foundation. 4 vertical posts are installed and fixed with metal corners with holes for self-tapping screws. 4 bars are mounted on top of the supports. The design will be in the form of a box. In the window and door openings, two beams are placed in a vertical position. Jumpers are installed between them.

To make the frame rigid, beams are installed diagonally on all sides of the future house. From corner to corner. The beams are secured by metal plates or corners, which are screwed with self-tapping screws. The frame is sheathed either with MDF sheets or boards. Only window and door openings are left.

Floor installation

The floor is installed according to the standard scheme - on logs. Logs are attached to the timber frame with a certain pitch, for example, 40 cm. Boards or plywood sheets are mounted on top of the frame. The flooring is secured with self-tapping screws.

After the work has been done it is necessary sand the floor. It’s better to do it right away than to breathe wood dust in a cramped room. Coarse and fine-grained sandpaper is used. It is not recommended to sand the floor surface without a respirator.

Making a roof begins with a frame. The bars are taken and installed in a triangular shape. A ridge beam is laid on top of the rafters, which will connect the entire structure. For additional rigidity, jumpers are installed. Here, metal corners and plates are also used to strengthen the structure. It is recommended to make the frame to the point where it becomes motionless when trying to stagger.

So, the roof skeleton is ready. Now we need to build the gables using boards or MDF sheets. Next the sides of the roof are sheathed. Next, a waterproofing film is installed on the roof surface. Then metal tiles or ondulin are installed. It is important that the roof slopes protrude beyond the walls by 15 cm.

Then the fillies are made and screwed to the rafters. Next, boards are screwed onto the frame to form a box. The structure is then covered with siding.

The building should reflect the real house as much as possible, so it is necessary to make a minimum of furniture. The first step is to impregnate the wood with special agents against rotting and beetles. After which the inside of the room should be varnished.

After processing, it is necessary to build furniture, for example: a chair, table, bed, etc. Only the furniture must be of minimal size to fit the mini house. Instead of making mini furniture, you can buy the same one, only plastic. All you have to do is go to a children's goods store and find the accessories you are interested in.

Manufacturing of windows and doors

In this final step, the windows and doors are installed. To make doors, you should cut out the MDF sheet to the required size and saw off the product with an electric jigsaw. A handle is attached to the door, installed in the opening and fixed evenly using wedges. Next, the door hinges are attached. After which the latch is installed.

Windows are installed using a slightly different technology. Two openings are equipped with cross-shaped lintels. You can also install glass there, but it is not recommended, since it is a breakable material that can harm a child. It is preferable to use polycarbonate. This material is mainly used for greenhouses. It is durable and flexible. It also transmits light. Pieces are cut to the size of the opening and screwed with self-tapping screws.

There are some nuances that need to be taken into account. They affect the safety of the child in the house. To keep the premises safe, it is recommended to adhere to the following rules:

1. The site for the construction of a mini-house should not be embossed or contain driftwood or similar objects that can cause injury. If a tree is chosen for a house, it must be reliable and strong.
2. After processing the wood, an inspection is carried out to identify defects. Because it is necessary to prevent the entry of splinters.
3. The screws are screwed tightly so that the caps do not peek out, otherwise you can get hurt by them.
4. By attempting to shake the structure, its strength is tested. If it wobbles, then additional reinforcement of the structure should be done, otherwise destruction from the wind or for another reason may occur.
5. The sharp corners of the metal tiles should be hidden, as the child may cut himself.

Mini cottage on a tree

This construction option is more complex than a regular house on the ground. In this case, the object is placed on a tree, or more precisely, on a branch. Otherwise, the technology is almost identical to the first option. The construction of a mini cottage on a tree consists of step-by-step actions:

1. For such purposes, hardwood trees are selected. But soft species, for example, walnut, are not suitable because they do not have a dense enough structure. Therefore, there is a risk of branch fracture. They also choose not old trees that have dried up or are about to dry out. They begin to rot, turning into dust. This is dangerous, because the tree can fall at any moment.
2. This step involves working out the idea for the house, and then creating a plan and drawing.
3. It is not advisable to install a building on a tree. It's easier to make the structure on the ground. The remaining fastening work is carried out on wood. The platform on which the mini-house for children will stand should be strengthened as much as possible. Each tree has its own individual shape, so supports and other reinforcing structures are made according to circumstances.
4. At this step, the ladder is installed. The structure is also assembled on the ground and then attached to a tree trunk. Be sure to tie a rope next to the stairs to ensure a safe descent.

True, it is safer to choose the option where the house is on the ground. After all, children run the risk of falling from a height of 3 meters, which can result in serious injury. However, as you can see, building a house for children out of wood with your own hands is very simple.