Do-it-yourself dismantling of brick partitions. Dismantling walls made of brick and concrete Features of dismantling partitions made of different materials

Removing a wall is not an easy task. Having certain knowledge and basic experience will greatly simplify its solution. In most cases, breaking is easier than building, as the wise saying goes. But not in the case of dismantling the walls in the apartment. You definitely won’t be prepared for so much dust and dirt, as well as hours of loud noise. However, as another saying goes: “If you are afraid of wolves, do not go into the forest.” If nothing can scare you, go ahead! To victory over dismantling!

Before starting dismantling, it is necessary to have a new layout of the apartment or house, as well as obtain permits for carrying out repair work. Having a new layout will allow you to avoid mistakes with the choice of the wall to be dismantled.

Documents for permission to demolish walls must be required. Firstly, not every wall can be dismantled (if the wall bears the main load, then its absence can cause deformation and further destruction of the entire house due to excess load on the remaining load-bearing walls). Risk, of course, is a noble cause, but not in this case. Secondly, it is prohibited by law to dismantle the walls yourself.

What walls are allowed to be dismantled?

There is a category of walls whose demolition is strictly prohibited. If you don’t understand this yourself, invite specialists. This will save you from a number of unpleasant moments. It is allowed to dismantle walls made of foam blocks and bricks, as well as plasterboard, concrete, wood, and stone. The easiest way to deal with wooden walls. Brick walls also lend themselves well to demolition. Dismantling monolithic walls is more labor-intensive.

Preparation for dismantling work

Before starting dismantling work, you must:

• turn off the heating;
• cut off access to gas;
• shut off the supply of cold and hot water;
• turn off all household electrical appliances, including the television antenna;
• isolate the radio point.

It is imperative to obtain an oral (or better yet, written) agreement from neighbors to carry out construction work. If your neighbors ask you to take a break from work for a certain time, you will have to meet them halfway. All work associated with increased noise and vibration can be carried out exclusively during the daytime - from 9.00 to 19.00 on weekdays. On weekends - prohibited!
Tools required for dismantling walls: sledgehammer, simple hammer, jackhammer, steel wedges, grinder (grinder), chisel, hammer drill, crowbar. Have thick construction bags ready to take out the trash.

How to dismantle a foam block wall

Foam block is a universal material from which it is easy to lay walls. It is also easy to saw and dismantle. First, remove the plaster, then use a sledgehammer to knock out one block at a time.

Dismantling plasterboard walls

When working with drywall, a lot of dust is generated, so all things need to be taken to another room, the furniture and floor should be covered with cloth or film.

Then proceed directly to dismantling:

• find and remove screws;
• remove the casing and disassemble the frame;
• demolish the wall with a hammer or sledgehammer (this is the cheapest method of dismantling);
• demolish a wall using diamond cutting (a rather expensive method that requires knowledge and experience).

How to dismantle a brick wall

To demolish a brick wall, you only need a sledgehammer. One brick at a time is knocked out of the wall, starting from the top, from the ceiling. If the integrity of the wall is lost, cracks will begin to appear between the bricks, and they will easily fall out with little pressure on them.

Dismantling partitions

When planning the demolition of walls, decide on the method by which you will carry out the dismantling work.

Dismantling can be done as follows:

• Breaking down walls in parts. Using a marker or felt-tip pen, divide the wall area into separate cells so that the weight of each cell does not exceed 10 kg. Then, using a grinder, cut the wall.
• Chiseling. You will need a chisel and a hammer drill. The method is one of the fastest, but at the same time the noisiest and also inaccurate.
• Drilling method. It is necessary to divide the wall into segments with a marker, then drill holes along them, closely adjacent to each other. After drilling, the dismantled area must be tapped and then removed using a chisel. You can use a hammer.

Before starting dismantling work, moisten a thick cloth with water and cover the room in which you are going to work with it. This way you will minimize dust contamination in the remaining rooms.

Home owners often think about how to properly demolish a wall in anticipation of redevelopment: the cost of dismantling is comparable to the construction of the same structure, and the desire to save money encourages them to do it themselves. The subtleties of the process are determined by the material: brick and blocks are easier to disassemble than a concrete surface.

Load-bearing walls are the fundamental elements of the structure; they serve as supports for the floors, so breaking them is prohibited. You can demolish conventional partitions made of the following materials:

• brick,
• concrete,
• foam block,
• stone,
• tree,
• drywall.

Their thickness usually does not exceed 38 cm.

If the repair affects internal partitions and walls - complete or partial demolition, formation or filling of openings - you first need to make sure that prior approval from the housing inspection is not required. Permission is not required in situations where manipulations affect only non-load-bearing structures.

In this case, the redevelopment will be legalized after the work has been completed. But there are exceptions: listed houses and buildings with wooden floors. In such a situation, before starting work, it is necessary to submit to the housing inspection a conclusion on the condition of the structure and the safety of the planned intervention. In relation to load-bearing walls, regulatory authorities can only give permission to construct an opening.

General rules of the process

If a wall is dismantled unprofessionally, there is a high probability of redistributing the load on the structure, so partial demolition is often carried out: an opening is formed, for example, resting on a column. Also, you cannot knock out the wall along the perimeter in one piece, otherwise the middle will collapse (this could be hundreds of kilograms), and disassembling and removing it will be extremely problematic.

Regular rules of operation using the example of a brick partition:

• the canvas is disassembled in small segments, knocking out brick by brick;
• in the case where there is a doorway in the location to be demolished, first remove the door lintel, gradually expanding the coverage upwards and to the sides;
• the main working tool when dismantling a brick surface is a sledgehammer; the wall is destroyed in the direction from the ceiling down;
• During the process, cracks form in the canvas, due to which the material will fall out on its own.

General techniques for correctly breaking down a wall in an apartment:

1. It will be easier to break the structure into parts. It is necessary to outline the weight and dimensions of the pieces to be removed in advance. In the case of concrete and brick, it will not be possible to lift more than 10 kg at a time. A concrete partition can be sawed with a grinder using an appropriate disk; it is advisable to first mark it with a marker. Such manipulations do not create much noise, but a lot of dust is generated.
2. Walls are often chiselled with a chisel and sledgehammer. It is important to act carefully here so as not to destroy the surrounding structures.
3. Professionals use a hammer drill and a drill: they divide the area into sections using markings, drill holes and gouge out pieces with a hammer or chisel.

Concrete and brick surfaces are generously sprayed with water to reduce the spread of dust. For the same purpose, the entrance to the room is covered with a wet sheet or piece of fabric.

Overview of required tools

The choice of tools is determined by the material from which the walls are made. In particular, if it is necessary to demolish a brick partition in the bathroom, it is advisable to prepare:

• pickaxe, crowbar;
• steel wedges;
• chisel;
• sledgehammer;
• jackhammer.

A wooden structure can be disassembled using a chainsaw; for a concrete structure, you will need a hammer drill, grinder, and jackhammer. More serious instrumentation in the latter case is explained by the presence of metal reinforcement in the concrete slab.

You will need the following protective equipment:

• respirators;
• gloves;
• masks;
• glasses;
• tight closed shoes;
• film for covering furniture, windows, floors.

Depending on the volume and scope of work, a spatula, nail puller, construction vacuum cleaner, or shovel may also be useful.

Preparatory work

When preparing an apartment, first of all, all communications are turned off: heating, water supply, television antenna, gas pipeline, sewerage, electricity (the list depends on the specifics of the premises affected by the redevelopment). You should also take care of packaging for the resulting construction waste - here you will need bags made of durable material.

A major overhaul involves getting rid of switches and sockets, built-in cabinets, screeds, doors and windows. As a result, bare walls and floor slabs should form.

Inside the dismantled surfaces there may be water pipes, fittings, and electrical wires. To find a hidden electrical network, you should use a non-contact probe. If wires become visible during demolition, you need to tap the pieces around them as carefully as possible, in no case allowing heavy pieces of material to sag on them.

Concrete walls in panel houses contain steel reinforcement, and here the fastest and most effective method of dismantling is the use of an angle grinder with a metal disc. The tool allows you to cut metal components efficiently.

If you are planning a bathroom renovation, you need to keep in mind that the plumbing is often hidden in the partition under the tiles. When purchasing an apartment that has already been finished, there is a high probability that there are pipes in the concrete wall. Therefore, the structure should be disassembled in the least destructive way. To prevent an emergency, you need to turn off the water and carefully dismantle the old communications.

Each region has its own regulations for organizing repairs in apartment buildings: hours are set during which noise is prohibited, and in most cases it is forbidden to disturb the silence on weekends.

Implement options

It is most convenient to use a grinder, a jackhammer, an impact drill or a hammer drill when destroying partitions. The choice of tool is determined by the scope of work and the base material of the wall.

A concrete wall can be cut down with a grinder equipped with an appropriate disk. To make the work easier, you should first mark the wall: as a result, pieces should be formed that are easy to control and move.

When choosing equipment, you need to take into account its power and the radius of the disk: the larger the last parameter, the thicker the wall to be removed can be. The advantages of the method are accuracy and lack of noise, the disadvantage is that a lot of dust is generated. Therefore, this method is not suitable for working in small rooms, for example, when demolishing a partition between a bathroom and a toilet: dust will instantly fill the space, and you will have to wait 15-20 minutes for it to settle, and with a new cut everything will repeat. Having a construction vacuum cleaner will help neutralize this effect, but it is common only among professionals.

Using an impact drill and hammer drill

This is the most convenient way to solve the problem yourself; it consists of drilling through holes close to each other according to pre-applied markings. When the piece is completely processed around the perimeter, it can be knocked out with a chisel and hammer, systematically tapping the material. The method is very noisy and dusty, but from the point of view of one’s own safety it is effective.

Using a jackhammer

A powerful tool allows you to quickly eliminate an unnecessary partition; it makes a lot of noise and requires careful handling. If you hammer without a clear plan, there is a high risk of destruction of surrounding structures.

Wall dismantling technology

Drywall and foam blocks are the most common materials for partitions, and their dismantling is not difficult: the texture and density of the structures facilitate their quick disassembly.

From foam block

This is a universal building material that can be used both in the construction of apartment buildings and in the construction of private houses. The blocks are quickly installed and exhibit excellent sound and heat insulation properties. Therefore, it is customary to assemble internal partitions from blocks, which must be dismantled; a little less often they are used in the construction of external walls.

The raw material for foam blocks is cellular concrete; it is light in weight, can be easily sawed and cut, and holes can be drilled in it using an electric or hand drill. You also need to take into account that special glue is used to connect products, and metal reinforcement is laid to enhance strength.

Taking into account the specified characteristics of foam blocks, it is necessary to prepare the following tools for work:

• sledgehammer,
• grinder,
• hammer,
• saw.

First, the top decorative layer (in particular, putty, plaster) is removed, then individual pieces of material are knocked out using a sledgehammer or hammer. In general, dismantling does not create difficulties; a lot of dust does not form during work.

It is prohibited to throw construction waste into standard containers located near houses, so the foam block wall should be broken into small fragments and packed in durable construction bags.

After all manipulations are completed, the waste is taken to a landfill.

From plasterboard

In apartment buildings built at the end of the last century, partitions based on plasterboard are common. This universal material is easy to break; the main thing is to take care of comfortable working conditions.

The preparatory stage boils down to the following activities:

• when destroyed, drywall creates a lot of dirt and dust, so it is important to vacate the premises in advance and carefully pack in film all furniture that cannot be removed;
• in the process of demolishing this type of partition, the floor will not be damaged, but it will have to deal with all the dirt that is generated. To facilitate subsequent cleaning, it is advisable to cover it with protective material or thick oilcloth;
• From the wall that is planned to be eliminated, you need to remove not only decorative elements, but also the door frame and electrical wiring.

Demolition of a structure can be carried out in several ways, depending on its type, since the composition may include plaster slabs or a metal frame. Here are 3 convenient dismantling methods:

1. If the partition is assembled from sheet cladding, first of all you need to find the screws and carefully remove everything (a magnet will help in the search). Next, remove the casing and begin disassembling the frame. The advantage of this method is the possibility of reusing the lathing and sheets to build a partition in another place. But there is also a drawback: to maintain the integrity of the materials, you will have to spend a lot of time and effort.
2. The easier impact method is based on the use of a sledgehammer or hammer. In this case, the material is completely destroyed and taken to a landfill.
3. If the task is to make a smooth opening in an existing wall, you should use a diamond cutter. This expensive equipment requires certain working skills.

In the latter case, it is important not only to rid the structure of wiring, it is advisable to draw up a plan for the future interior in advance in order to accurately mark and maintain proportions.

The question of how to demolish a wall in an apartment yourself, preferably without dust, arises when the need arises to remodel the home. When preparing for this work, you should understand that during its implementation you will have to face various unexpected problems, but it is quite possible to complete it on your own.

To eliminate the possibility of extremely unpleasant surprises and provide yourself with legal protection, first of all, you need to obtain permission from the housing authorities.

If you decide to demolish a wall in an apartment without first checking the possibility of performing this operation, you may encounter extremely unpleasant problems.

Before carrying out work, you must invite a specialist architect who can advise on the possibility of redevelopment. The same specialist can assist in drawing up a sketch of the upcoming demolition. If the redevelopment is quite extensive, then a project will be required, which should be ordered from a construction company. Permission to demolish wall structures is obtained on the basis of a project, which is then submitted to the BTI for changes.

The work must be carried out in strict accordance with the project, and upon completion, the correctness of the work must be checked by a specially invited commission.

What tools are needed to demolish a wall in an apartment yourself?

It will hardly be possible to demolish a wall in an apartment completely without dust. Therefore, before starting work, all furniture should be carefully covered with film. You also need to make sure that there are no communications or electrical wiring in the wall.

Then you should choose the tool that suits best. To demolish a wall you can use:

• grinder, about the choice of which;
• a powerful hammer drill, which you can read about;
• with a jackhammer.

The work begins with marking, and the demolition of the wall is always carried out in parts.

How to demolish a wall with a jackhammer

The use of this tool is only possible if no one lives in the apartment and it is completely free of household items. This is because working with a jackhammer is extremely noisy and dusty.

Having decided to demolish the wall with the help of knock-down milk, you need to completely empty the apartment

How to break a wall with a grinder

In order for the grinder to be able to cope with dismantling work, it is necessary to install a disk on it that allows cutting concrete. To perform dismantling, the wall material is cut into pieces, following the pre-applied markings. The advantage of using an angle grinder is to minimize the noise produced and to be neat.

This is how a wall is dismantled using a grinder

How to demolish a partition with a hammer drill

Demolition of a wall using a hammer drill is the least dusty and efficient. To dismantle the partition, through holes are drilled in it along the existing marking lines. Next, individual pieces are simply knocked out using a chisel and hammer.

This is how a wall is demolished using hammer drills

Upon completion of the work, all waste is collected and removed.

Wall dismantling: cost of work

Since dismantling walls is a fairly complex job, you can turn to specialists to carry it out. On average, the cost of this operation is about 500 rubles/m2. However, this figure can vary significantly depending on the thickness and material of the wall being dismantled.

How to demolish a wall in an apartment yourself (video)

In addition to those described above, there are other methods for dismantling interior walls in an apartment. One of them is presented in the video, which we invite you to watch.

Today, many people are experiencing a shortage of living space. In particular, this applies to residents of Khrushchev and other houses of similar construction. The peculiarity of such buildings is that the rooms and premises have a rather small area. As a result, this leads to discomfort. Who would want to live with such restrictions? This problem is solved in different ways. If you know how to tear down the wall between the kitchen and the room, then solving the problem is a matter of time.

Redevelopment

In fact, space shortages are solved in several ways. In the first case, you can sell a small apartment and buy another property with a larger area. But not everyone has the opportunity to carry out such a financial transaction. An alternative way is to demolish the wall between the kitchen and the room. The redevelopment will slightly increase the usable area of ​​the apartment.

When demolishing the wall between the room and the kitchen, certain features must be taken into account. To begin with, this concerns the design of work. According to the law, work related to redevelopment is initially coordinated with the BTI. Otherwise, serious problems await you. Unauthorized redevelopment can lead to a fine and problems with the sale of the apartment. Carrying out such work and diamond drilling must be recorded in documents.

What is subject to demolition

If you decide to demolish the wall between the kitchen and the room yourself, then you need to take into account certain features. First of all, this concerns the purpose of the structure. It is prohibited to demolish load-bearing walls. Only interior partitions can be broken. As for load-bearing walls, they bear a large functional load. This applies to external walls and structures that support reinforced concrete slab floors. The purpose of the wall can be determined by the material used or its thickness.

Consider reinforced concrete houses. In them, the load-bearing walls have a thickness of at least 12 cm. The thickness of the interior partitions does not exceed 10 cm. For the construction of interior walls, panels made of reinforced concrete or gypsum concrete are used. As for brick buildings, the thickness of the walls depends on the width of the brick and the joint. Thus, the partitions here have a thickness of no more than 12 cm, load-bearing walls are up to 64 cm. For the construction of partitions, both brick and gypsum concrete panels are used here.

Important: in order to make accurate measurements, it is necessary to free the wall from finishing to the very base.

In monolithic buildings it is very difficult to determine the purpose of the wall. This is due to the fact that foam blocks are used to construct interior partitions. They are used to create walls whose thickness can reach 20 cm or more. In this case, if you decide to demolish the wall between the room and the kitchen, then it is better to use an architectural project on which such structures are precisely marked.

Step by step process

On video: kHow to break a wall without noise and dust.

Remodeling an apartment is a very responsible process, especially when it comes to demolishing the wall between rooms. When dismantling a structure, you must follow the established rules and sequence. This will allow you to carry out the work efficiently and avoid many problems.

You can demolish the wall between rooms in the following sequence:

• Turn off the power to the room which will clear the wall of wiring. Using a chisel, the wall is opened and the cable is removed from it. All switches and sockets are also eliminated. The cable is cut and its end is insulated.

• Remove the pipework from the partition. Remove skirting boards and trim.

• Prepare the tool, which will be needed when performing work.

• Clear the room of furniture. If this is not possible, then all interior elements are stored under the opposite wall. To protect objects and furniture from dust, they are carefully covered with plastic film.

• Place cardboard on the floor or other material that will protect the floor covering from damage. If the gender changes, then this process can be missed.

• Demolition of the wall between the kitchen and the room carried out using gloves, glasses and a respirator. Such safety measures are due to the fact that dust has a very negative impact on human health.

When dismantling the interior partition, you must strictly follow the advice of the professionals. This will allow you to carry out the work efficiently and protect yourself from injury.

How to demolish walls made of different materials

Demolition of the wall begins from the top corner. It is prohibited to carry out demolition in the middle of the structure or from below. Failure to comply with this rule may result in injury during dismantling work. When demolishing a partition, it is worth considering what material it is built from. Certain features of dismantling work will depend on this.

Brick walls

Remove trim and baseboards. Thanks to such work, it is possible to observe the brickwork. Bricks are removed along the seams using a chisel and hammer. A sledgehammer and a jackhammer are often used for this. Regardless of the tool, dismantling the partition begins from the top corner.

Reinforced concrete walls

Partitions are demolished using a grinder, a jackhammer and a hammer drill. A spacer is installed between the floor and ceiling, which serves as a safety measure against the structure falling. The partition is broken down to a reinforced frame. It can be removed using a grinder. The partition is demolished in parts, which prevents the structure from falling and injuring workers.

Plasterboard partitions

They are the easiest to disassemble. You just need to remove the sheets of drywall and dismantle the frame.

plaster wall

Demolition is carried out as the dismantling of reinforced concrete structures. This partition contains reinforced wire. Its thickness is 6 mm. To break the structure, it is necessary to knock down the plaster to the wire, which is cut with a grinder. As a result, for demolition you will need a hammer drill, a hammer and a grinder.

With this information, you can quickly and efficiently demolish the wall between the kitchen and the room. The main thing is to remember safety. All work is carried out using gloves, a respirator and goggles.

Features of old houses

The demolition of walls between adjacent rooms is often carried out in old houses - Khrushchev buildings. The buildings are characterized by a small area of ​​premises. The work is carried out taking into account certain features related directly to the structure itself. Often, interior walls are lightweight partitions, which makes it possible to dismantle them. Of course, before starting work, you need to check whether the structure is load-bearing.

Do not forget about other restrictions associated with the structure. This is especially true for wet areas of apartments, such as the bathroom and toilet. Such premises cannot be placed above living rooms and kitchens. You can increase the area of ​​the room only through a storage room or corridor.

So, in order to tear down the wall between the kitchen and the room, you need to have certain knowledge. This will allow you to correctly determine the functional load of the structure and the possibility of its demolition. And do not forget that the analysis of the structure starts from the top. This will prevent the wall from falling and injury as a result of redevelopment.

2 videos about proper demolition of walls

Demolition of walls in pictures (30 photos)

In recent years, during the renovation process, many people decide to remodel their home. For some, this is an opportunity to rationally use the resulting space or give the room a more modern look. In any case, regardless of the reasons for the redevelopment, this process affects important and at the same time dangerous procedures. We are talking about demolishing walls in an apartment. This is exactly what many people resort to when creating a new look for their apartment. Accordingly, demolishing a wall in an apartment is quite a sensitive matter.

Apartment redevelopment! What is needed for this?

All work related to redevelopment concerns two important aspects:

1. Obtaining relevant documents and permits.
2. Demolition of walls.

At first glance, everything is quite simple and consistent. Moreover, many people know the principle that breaking does not build. But as for the demolition of load-bearing walls or partitions, the whole situation is different. The work of demolishing walls is very exhausting and difficult.

Before you start work, you need to think about what the project of the future apartment will be.

During the planning process, consider whether a particular wall can be demolished! Not every wall can be torn down.

In each apartment there are two types of walls:

1. Partition.
2. Carrier.

As for the latter, these are walls that are an integral part of the entire building. For the ceiling, the wall is the support. You can't touch such walls! As for the other walls, these are partitions that divide the entire area of ​​the apartment into functional zones. They are built from lightweight materials. When they are removed, the load from the floor is not redistributed, so they can be safely demolished, but only after appropriate permission. So, partitions are divided into the following categories:

1. Concrete.
2. Brick.
3. Stone.
4. Wooden.

In each individual case, the technique for demolishing walls will differ, but not much. When demolishing a wooden wall, you will need to put in less effort and time than when demolishing a concrete partition.

If you don't know which wall can be demolished and which can't, then seek professional guidance. They will draw up a detailed design of your apartment and point out exactly the partitions that are allowed for demolition.

Breaking does not build! Let's start the process

Immediately before work, you need to make sure that all important communication networks are disconnected or cut off. For example it could be:

• Gas pipeline.
• Television.
• Internet.
• Electricity.
• Radio and the like.

A variety of tools may be required, depending on the wall material, for example:

• Crowbar/pick.
• Jackhammer.
• Steel wedges.
• Sledgehammer.
• Hammer.
• Bulgarian.
• Hacksaw.

From this list it follows that for wooden walls a chainsaw or a simple hacksaw will be enough, but for concrete walls you will need a more serious tool. For example, inside a concrete wall there is usually a binding material such as reinforcement. During the process of dismantling the walls, it will need to be cut off with a grinder. As you can see, when demolishing walls, you may need not one, but several construction tools at once.

When everything is ready and you have decided on the choice of tool, you can begin the long-awaited changes - demolishing the walls!

The process of demolishing a wall should always start from the top down so that the top of the wall does not collapse on your head.

First, you need to remove the finishing material from the wall, this can be plaster, drywall, etc. As for plasterboard walls, you should also remove the frame that was the basis for the drywall. If the wall is brick, then one brick is knocked out from above and so on.

If there is a door in the brick partition that is to be demolished, then the wall should be demolished from it.

During dismantling work, it may be tempting to save the material that is being dismantled, such as brick. But you shouldn't do this. Why? The thing is that this material has lain under different loads for decades. Accordingly, this led to the fact that it will no longer have sufficient strength and quality.

If you have concrete partitions, you will have to work with a grinder, a chipper, and even a hammer drill. Using a hammer drill and a grinder, you can make successive grooves in the wall. This is necessary in order to immediately divide the wall into several pieces. With a grinder you can cut through the reinforcement running through the body of the wall. Using a hammer, you can speed up the work process, since its impact force is much greater than the force of a hammer drill.

Sometimes you have to deal with high-strength concrete that a hammer, grinder and hammer drill cannot handle. What to do in such cases? In such a situation, you will need the help of a specialist who will remove the wall to small pieces using diamond equipment.

Although you may have a desire to demolish walls using diamond equipment yourself, it is better not to take risks, but entrust the work to professionals.

What is achieved by demolishing walls?

In most cases, redevelopment is carried out in the toilet, bathroom and kitchen. Although there are cases, it is rare when redevelopment occurs in residential premises. Demolition of walls and installation of new ones allows you to redistribute work areas and recreation areas in your apartment. You can also save space. For example, a bathroom will be combined with a toilet, so that one room will perform several functional tasks at once. But, despite all this, it will not be possible to solve the problem of lack of living space in this way. After all, if an apartment has forty square meters, it will not become larger after demolition and installation of new walls.

So, as you can see, redevelopment is directly related to the demolition of walls and their relocation. In some cases, you can use the services of designers who will tell you how to perform this work most efficiently.

There is no need to rush to demolish the walls. You can always break it at any time. First of all, plan everything carefully and calculate all your expenses so that you can complete the renovation. If you still decide to make such drastic changes, then you should carefully prepare. For example, think about where and how you will dispose of all construction waste. Remember that you cannot throw garbage into containers; you will have to hire a car.

We hope that this article will help you cope with such a difficult task as demolishing walls and partitions in your apartment. If you already have such experience, then write to us about it in the comments to the article.

Video

A noise-free and dust-free method for demolishing a non-permanent partition in an old house: